Piston installation. Please help
- FloridaBiker
-
- Offline
- User
-

Registered
- Posts: 233
- Thanks: 4
Re: Piston installation. Please help
28 Sep 2007 11:02
I put the pistons on the rods first, and use well oiled hose clamps as ring compressors.
Goes together real easy.
Goes together real easy.
Please Log in or Create an account to join the conversation.
- reborn650
-
- Offline
- User
-

Registered
- Posts: 693
- Thanks: 5
Re: Piston installation. Please help
29 Sep 2007 22:42
Have a buddy help out. An extra set of hands are very helpful unless you are an experienced builder.
Since you have bored out the 750's cylinders you will notice the original wall thickness is significantly reduced in thickness compared to the stock factory bore and cylinder thickness. The bottoms of my 810 cylinders are almost razor sharp as my machine shop had barely any cylinder wall to work with.
Because of this, there is not very much metal to have a chamfer (angle cut) on the bottom of the cylinders. A good healthy chamfer really helps to compress the rings evenly and everything snugs in smoothly.
I have had my motor apart a couple of times and have found that Sandy's advice is dead on, do number 2 and 3 first and as Jay mentioned, popsicle sticks work very nicely and will not damage the rings as the wood is softer than the rings.
Take your time and make sure that the rings are all installed as per the instructions in the boxes. You don't want to put in a ring upside down.
BTW, I use Lucas Oil additive any time I reassemble engine parts that require lubrication. The stuff is thick like honey and comes in a plastic bottle with a cone-shaped applicator as a top. This lubricant doesn't drip off parts due to its thick viscosity in case you end up taking longer than expected to reassemble the motor and it also burns off fairly quickly.
Cheers-Colin Firth-Ontario Canada
Post edited by: reborn650, at: 2007/09/30 01:44
Since you have bored out the 750's cylinders you will notice the original wall thickness is significantly reduced in thickness compared to the stock factory bore and cylinder thickness. The bottoms of my 810 cylinders are almost razor sharp as my machine shop had barely any cylinder wall to work with.
Because of this, there is not very much metal to have a chamfer (angle cut) on the bottom of the cylinders. A good healthy chamfer really helps to compress the rings evenly and everything snugs in smoothly.
I have had my motor apart a couple of times and have found that Sandy's advice is dead on, do number 2 and 3 first and as Jay mentioned, popsicle sticks work very nicely and will not damage the rings as the wood is softer than the rings.
Take your time and make sure that the rings are all installed as per the instructions in the boxes. You don't want to put in a ring upside down.
BTW, I use Lucas Oil additive any time I reassemble engine parts that require lubrication. The stuff is thick like honey and comes in a plastic bottle with a cone-shaped applicator as a top. This lubricant doesn't drip off parts due to its thick viscosity in case you end up taking longer than expected to reassemble the motor and it also burns off fairly quickly.
Cheers-Colin Firth-Ontario Canada
Post edited by: reborn650, at: 2007/09/30 01:44
-1977 Kz650 Custom bought new by brother. Now with 810 kit, GPz750 cams, intake valves, Mikuni 29 smoothbores, velocity stacks, Dyna Igntion, MAC pipe and other goodies.
-1982 Ferrari 308 GTSi Red/Tan
-Toyota FJ Cruiser - 6 speed tank
-2010 Mazda CX-7 Turbo (my bride's)
-1998 Jeep TJ Wrangler 4.0 litre for the kids
-1975 Zamboni - The real Italian sportscar fully restored and functioning every winter at our local outdoor playground rink.
Mine is an ecclectic collection of motorized toys - LOL
I have a newspaper route and a web site where you can plan your own funeral life celebration www.mysendoff.com ....and go out with your own style.
-1982 Ferrari 308 GTSi Red/Tan
-Toyota FJ Cruiser - 6 speed tank
-2010 Mazda CX-7 Turbo (my bride's)
-1998 Jeep TJ Wrangler 4.0 litre for the kids
-1975 Zamboni - The real Italian sportscar fully restored and functioning every winter at our local outdoor playground rink.
Mine is an ecclectic collection of motorized toys - LOL
I have a newspaper route and a web site where you can plan your own funeral life celebration www.mysendoff.com ....and go out with your own style.
Please Log in or Create an account to join the conversation.
- CoreyClough
-
- Offline
- User
-

Registered
- GPz550 Addiction
- Posts: 1093
- Thanks: 83
Re: Piston installation. Please help
29 Sep 2007 22:59
Anyone set their ring end gap before installing the assembled pistons in the cylinders? What should his end gap be on his 810 kit?
Wondering what that gap should be on my 615 kit, as I'll be doing this in a about 3-4 weeks.
Wondering what that gap should be on my 615 kit, as I'll be doing this in a about 3-4 weeks.
'85 GPz550(ZX550-A2)
GPz550 Base Manual --> tinyurl.com/ze5b3qo
GPz550 Supplement Manual --> tinyurl.com/h34d2o6
GPz550.com --> www.nwsca.com/scripts/gpz_forum_2005/default.asp
First Race Win GPz550 --> tinyurl.com/o5y3ftp
GPz550 Base Manual --> tinyurl.com/ze5b3qo
GPz550 Supplement Manual --> tinyurl.com/h34d2o6
GPz550.com --> www.nwsca.com/scripts/gpz_forum_2005/default.asp
First Race Win GPz550 --> tinyurl.com/o5y3ftp
Please Log in or Create an account to join the conversation.
- Sandy
-
- Offline
- User
-

Registered
- Fly High,Tony
- Posts: 2448
- Thanks: 13
Please Log in or Create an account to join the conversation.
- nads.com
-
- Offline
- User
-

Registered
- Posts: 993
- Thanks: 20
Re: Piston installation. Please help
30 Sep 2007 22:31
stay away from popsickle sticks! They are used for craft work only. If your oil rings have decent tension you will not be able to push them in with anything other than a clamp or compressor. starting with the inside pistons is a very good method as opposed to all four at once. This method allows the cylinder block to fall down over the ring once it has been compressed by the clamp. If you do not have a champfer at the bottom of the sleeves, you can tape the point of a round file to protect the cyl. walls and make your own champfer. This is safe and easy and ensures the rings will not try to hang up. Have someone hold the block up while you work the rings in so the weight on the rings is reduced. If you choose to champfer, use some 220 paper to smooth the champfers. Don't let anyone talk you into letting the oil can set on the shelf.
Please Log in or Create an account to join the conversation.
- CoreyClough
-
- Offline
- User
-

Registered
- GPz550 Addiction
- Posts: 1093
- Thanks: 83
Re: Piston installation. Please help
30 Sep 2007 22:33
Thanks Sandy! Saved it to my favorites. Just need the proper machine to grind them needed. :blink:
'85 GPz550(ZX550-A2)
GPz550 Base Manual --> tinyurl.com/ze5b3qo
GPz550 Supplement Manual --> tinyurl.com/h34d2o6
GPz550.com --> www.nwsca.com/scripts/gpz_forum_2005/default.asp
First Race Win GPz550 --> tinyurl.com/o5y3ftp
GPz550 Base Manual --> tinyurl.com/ze5b3qo
GPz550 Supplement Manual --> tinyurl.com/h34d2o6
GPz550.com --> www.nwsca.com/scripts/gpz_forum_2005/default.asp
First Race Win GPz550 --> tinyurl.com/o5y3ftp
Please Log in or Create an account to join the conversation.
- auggiedog
-
- Offline
- User
-

Registered
- Posts: 94
- Thanks: 1
Re: Piston installation. Please help
02 Oct 2007 18:45
I have been using the hose clamps now and they work great...they are a little narrow, so they just fit the width of the space between the top an oil scaper rings, so you just got to go slow.
but, they slip right in...one person job too..
but, they slip right in...one person job too..
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
