cam timing question

  • Bicycle Lee
  • Bicycle Lee's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 319
  • Thanks: 0

Re: cam timing question

22 Mar 2009 08:30
#274200
just reassembled it and got it to where I am comfortable with the result.
I have a quick question though:
When I rotate the crank everything moves smooth and fine and then right when I'm passing TDC on 2-3 the chain gets a little slack in it. What could make this happen?
1978 KZ1000 police

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: cam timing question

22 Mar 2009 08:39 - 22 Mar 2009 08:40
#274208
Bicycle Lee wrote:
just reassembled it and got it to where I am comfortable with the result.
I have a quick question though:
When I rotate the crank everything moves smooth and fine and then right when I'm passing TDC on 2-3 the chain gets a little slack in it. What could make this happen?

At TDC is when the rear side of camchain has the most slack, and is the position when the routine camchain adjuster maintenance setting should be performed.

Good Luck! :)
1973 Z1
KZ900 LTD
Last edit: 22 Mar 2009 08:40 by Patton.

Please Log in or Create an account to join the conversation.

  • Bicycle Lee
  • Bicycle Lee's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 319
  • Thanks: 0

Re: cam timing question

22 Mar 2009 09:38
#274226
thanks... everything is looking good. My valve clearances are about .001" higher on 2&3 intake and exhaust than I'd like them to be, but that should be fine. It'll still fire.
1978 KZ1000 police

Please Log in or Create an account to join the conversation.

  • Bicycle Lee
  • Bicycle Lee's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 319
  • Thanks: 0

Re: cam timing question

22 Mar 2009 12:13
#274249
so.....

IT FIRED


If the video turned out I'll post it
1978 KZ1000 police

Please Log in or Create an account to join the conversation.

  • irishwill
  • irishwill's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 597
  • Thanks: 7

Re: cam timing question

22 Mar 2009 12:48
#274255
Atta boy....feels good when you get through a snag....dont it.

Please Log in or Create an account to join the conversation.

  • Bicycle Lee
  • Bicycle Lee's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 319
  • Thanks: 0

Re: cam timing question

22 Mar 2009 13:47
#274267
sure does...
although I'm getting a lot of smoke coming from the exhaust ports.
My head gasket seems to be leaking as well (which sucks cuz it's brand new).
It doesn't smell like burned oil, but I suppose it could be.
Is this to be expected when starting a motor for the first time? Does engine assembly lube make it smoke like that? Do new piston rings need some break in time and could that lead to a little oil in the exhaust??
any thoughts? Granted, I know the thing is 30 years old and a little leak is to be expected, but I'm wondering if there is anything else I should be looking for?
other than that it runs fine... starts right up, throttles nice... idles fine.
1978 KZ1000 police

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: cam timing question

22 Mar 2009 14:07 - 22 Mar 2009 14:08
#274271
it may just be too much asemble lube or oil burning at start up . dont worry unless it doesnt go away. but the head gasket leak worries me. when the motor has cooled completely, retorque it, in the proper torque sequince order. loosen each bolt a wee bit then retorque it. then go on to the next bolt. some guys dont loosen them first but i do. also, i put a bit of silicone under each bolt head to help keep the oil in and act at a torque lube..the copper washers are suposed to do that for u but i like to do everything to the extreme.It's a fault i know.:lol:
How did it run? what did u replace in the motor?
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Last edit: 22 Mar 2009 14:08 by mark1122.

Please Log in or Create an account to join the conversation.

  • Bicycle Lee
  • Bicycle Lee's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 319
  • Thanks: 0

Re: cam timing question

22 Mar 2009 15:40 - 22 Mar 2009 15:42
#274306
ran great! the first start I aided with a little starter fluid, but after that it fired right away and ran strong. Gotta tweak the idle and fix that silly gasket leak, but man was it good to hear that thing firing... man it sounded mean!!!
So here's what's new in the motor: new rings (bore honed as well), new exhaust valves (the intake ones were fine), port work done on the head (Larry Cavanaugh did a great job) and new Andrews cams. I got new coils too.
The gasket is that two part gasket for the cylinder head and the oil is coming from the middle where the gasket doesn't cover it. I don't know if that helps the troubleshooting.
I DID give the inside of the cylinders a good amount of assembly lube so hopefully that is all it is... how long until I should start worrying about it?
If it were burning oil wouldn't it SMELL like it? Because it didn't really smell like burning oil... and the smoke was more gray and white than black. Maybe the fumes had gotten to me by then though. ;)
1978 KZ1000 police
Last edit: 22 Mar 2009 15:42 by Bicycle Lee.

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: cam timing question

22 Mar 2009 17:52
#274353
did u put the large o-ring in the block, between the 2 head gaskets?
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • keith1
  • keith1's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1646
  • Thanks: 3

Re: cam timing question

22 Mar 2009 18:38
#274369
mark1122 wrote:
did u put the large o-ring in the block, between the 2 head gaskets?



man i hope he did....i was wondering the same thing....fingers crossed.....

Please Log in or Create an account to join the conversation.

  • DoubleDub
  • DoubleDub's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: cam timing question

22 Mar 2009 18:56
#274375
This is the o-ring they are refering to:

www.z1enterprises.com/detail.aspx?ID=2717

Site between the two halves of the head gasket.

Please Log in or Create an account to join the conversation.

  • Bicycle Lee
  • Bicycle Lee's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 319
  • Thanks: 0

Re: cam timing question

22 Mar 2009 19:09 - 22 Mar 2009 19:13
#274377
Hahaha.... I was like, "O-ring?? Oh shit...." but yes, I DID put that piece in. I didn't really think of that as an "O" ring... haha...
I also see that Z1 has a one piece copper gasket.... I might just have to get that.... I mean, the ones I have on there now are brand new and they're leaking... so maybe a one-piece is the way to go???
1978 KZ1000 police
Last edit: 22 Mar 2009 19:13 by Bicycle Lee.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum