Some 903cc questions
- hardr0ck68
-
Topic Author
- Offline
- User
-

Registered
- Who put the what in the where?
- Posts: 798
- Thanks: 3
Re: Some 903cc questions
28 Oct 2009 16:50
I need help figuring if these pistons will give me anything near the compression I need.
Does anyone know of a way I can figure out what the compression these pistons will be on a gpz750 head?
Does anyone know of a way I can figure out what the compression these pistons will be on a gpz750 head?
1977 kz650 c1
bought it because I was told it would never run again...I like to prove people wrong.
bought it because I was told it would never run again...I like to prove people wrong.
Please Log in or Create an account to join the conversation.
- Lorcan
-
- Offline
- User
-

Registered
- Speed Loony
- Posts: 580
- Thanks: 60
Re: Some 903cc questions
01 Nov 2009 06:48
The only way is to install them and measure.
760cc - 8.69@162mph
810cc, 211mph www.750turbo.com
www.stormdragbike.com
810cc, 211mph www.750turbo.com
www.stormdragbike.com
Please Log in or Create an account to join the conversation.
- 77KZ650
-
- Offline
- User
-

Registered
- Posts: 1397
- Thanks: 7
Re: Some 903cc questions
06 Nov 2009 08:50
why not send the crank to Jay to be stroked while youre at it? go over 900cc. its just adding a cylinder spacer and retiming the cams(after you make sure everything has enough clearance)
07 MDP Rookie of the Year
01 ZX-12R street/drag bike. 8.97 @155.7 pump gas, dot tires, no bars, no power adders. top speed in the 1/4: 161MPH
01 ZX-12R street/drag bike. 8.97 @155.7 pump gas, dot tires, no bars, no power adders. top speed in the 1/4: 161MPH
Please Log in or Create an account to join the conversation.
- Lorcan
-
- Offline
- User
-

Registered
- Speed Loony
- Posts: 580
- Thanks: 60
Re: Some 903cc questions
06 Nov 2009 09:24
If you take that route (and it won't be cheap) I'm told that GPz900R rods are 4mm longer, which would help with the rod/stroke ratio. They have the same size big end and the turbo size small end (16mm) though so you'd have to use pistons with that size pin.
760cc - 8.69@162mph
810cc, 211mph www.750turbo.com
www.stormdragbike.com
810cc, 211mph www.750turbo.com
www.stormdragbike.com
Please Log in or Create an account to join the conversation.
- hardr0ck68
-
Topic Author
- Offline
- User
-

Registered
- Who put the what in the where?
- Posts: 798
- Thanks: 3
Re: Some 903cc questions
06 Nov 2009 20:08
I have been thinking of this, and the stroke/destroke issue. If I were to spend money I would go farther under square... for now at least I am going to leave the stroke as it is; until I can find a way to work the hp numbers for stroked vs de-stroked.
As for the compression, when I get time I will bother apejay and see if he can get me the dome displacement of those pistons; then I will check cometic and see what size head gaskets they offer. There is a good calculator online to tell the compression... hopefully when I get the numbers it will come out 9:1 or higher...
As for the compression, when I get time I will bother apejay and see if he can get me the dome displacement of those pistons; then I will check cometic and see what size head gaskets they offer. There is a good calculator online to tell the compression... hopefully when I get the numbers it will come out 9:1 or higher...
1977 kz650 c1
bought it because I was told it would never run again...I like to prove people wrong.
bought it because I was told it would never run again...I like to prove people wrong.
Please Log in or Create an account to join the conversation.
- 77KZ650
-
- Offline
- User
-

Registered
- Posts: 1397
- Thanks: 7
Re: Some 903cc questions
09 Nov 2009 06:17
i dont see the need to destroke one of these motors. unless you plan on revving it to 13000, piston speed shouldnt really be the limiting factor with a mild stroke should it? im guessing stock revlimit would be plenty safe with a 3 or 4mm stroke. it would up the compression, and create a lot of tq
07 MDP Rookie of the Year
01 ZX-12R street/drag bike. 8.97 @155.7 pump gas, dot tires, no bars, no power adders. top speed in the 1/4: 161MPH
01 ZX-12R street/drag bike. 8.97 @155.7 pump gas, dot tires, no bars, no power adders. top speed in the 1/4: 161MPH
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
