Compression question
- PLUMMEN
-
- Offline
- User
-

Registered
- Posts: 7983
- Thanks: 104
Re: Compression question
12 May 2010 09:25
check your timing
Still recovering,some days are better than others.
Please Log in or Create an account to join the conversation.
- KZCool
-
Topic Author
- Offline
- User
-

Registered
- Posts: 150
- Thanks: 1
Re: Compression question
12 May 2010 11:10
PLUMMEN wrote:
Do you mean the timing chain that goes around the cam and top rotors?
check your timing
Do you mean the timing chain that goes around the cam and top rotors?
1976 KZ750 hardtail
Please Log in or Create an account to join the conversation.
- BSKZ650
-
- Offline
- User
-

Registered
- Posts: 2061
- Thanks: 14
Re: Compression question
12 May 2010 14:36
KZCool wrote:
prob meant ignition timing
PLUMMEN wrote:check your timing
Do you mean the timing chain that goes around the cam and top rotors?
prob meant ignition timing
77 kz650, owned for over 25 years
77 ltd1000, current rider
76 kz900, just waiting
73 z1,, gonna restore this one
piglet, leggero harley davidson
SR, Ride captian, S.E.Texas Patriot Guard Riders.. AKA KawaBob
77 ltd1000, current rider
76 kz900, just waiting
73 z1,, gonna restore this one
piglet, leggero harley davidson
SR, Ride captian, S.E.Texas Patriot Guard Riders.. AKA KawaBob
Please Log in or Create an account to join the conversation.
- KZCool
-
Topic Author
- Offline
- User
-

Registered
- Posts: 150
- Thanks: 1
Re: Compression question
13 May 2010 07:33
ok well i took the valve cover off, aligned the TDC mark on the crankshaft. the arow on the rear sprocket was flush with the cylinder head and the 32nd pin in the chain was were it was supposed to be on the front sprocket, but the front arrow wasn't flush with the cylinder head like my manual shows, any thoughts. And why would the ignition timing be a problem for compression if it wont start?:blink:
1976 KZ750 hardtail
Please Log in or Create an account to join the conversation.
- PLUMMEN
-
- Offline
- User
-

Registered
- Posts: 7983
- Thanks: 104
Re: Compression question
13 May 2010 07:55
if your ignition timing was advanced too much wont start
Still recovering,some days are better than others.
Please Log in or Create an account to join the conversation.
- PLUMMEN
-
- Offline
- User
-

Registered
- Posts: 7983
- Thanks: 104
Re: Compression question
13 May 2010 08:05
KZCool wrote:
how far above/below was it?ok well i took the valve cover off, aligned the TDC mark on the crankshaft. the arow on the rear sprocket was flush with the cylinder head and the 32nd pin in the chain was were it was supposed to be on the front sprocket, but the front arrow wasn't flush with the cylinder head like my manual shows, any thoughts. And why would the ignition timing be a problem for compression if it wont start?:blink:
Still recovering,some days are better than others.
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: Compression question
13 May 2010 08:17
PLUMMEN wrote:
I second this question - on my 900 there is pressure from the valve springs that causes the hash mark not to line up perfectly until the chain is tightened and I turn the engine so that the camshaft turns an entire rotation.
Please note that not everyone agrees that this is best practice as if things are off a valve and cylinder head might touch while turning the engine over.
how far above/below was it?
I second this question - on my 900 there is pressure from the valve springs that causes the hash mark not to line up perfectly until the chain is tightened and I turn the engine so that the camshaft turns an entire rotation.
Please note that not everyone agrees that this is best practice as if things are off a valve and cylinder head might touch while turning the engine over.
Please Log in or Create an account to join the conversation.
- KZCool
-
Topic Author
- Offline
- User
-

Registered
- Posts: 150
- Thanks: 1
Re: Compression question
13 May 2010 08:33
the rear hash mark is about a quarter inch high, so the arrow is a quarter inch below the head.
i've also already trightened it ad turned it a few times with the crankshaft and a 17mm wrentch. ill post a picture
i've also already trightened it ad turned it a few times with the crankshaft and a 17mm wrentch. ill post a picture
1976 KZ750 hardtail
Please Log in or Create an account to join the conversation.
- KZCool
-
Topic Author
- Offline
- User
-

Registered
- Posts: 150
- Thanks: 1
- KZCool
-
Topic Author
- Offline
- User
-

Registered
- Posts: 150
- Thanks: 1
Re: Compression question
13 May 2010 11:13
so i just fixeed my ignition timing. you were right, very off. i'm gonna put the valve cover back on and try it out : )
1976 KZ750 hardtail
Please Log in or Create an account to join the conversation.
- KZCool
-
Topic Author
- Offline
- User
-

Registered
- Posts: 150
- Thanks: 1
Re: Compression question
13 May 2010 13:24
wellmy bikes running now, but i had to get rid of the electric start, something was screwy withit and it was holding the crankshaft. It does have some problems with one cylinder cutting out after a bit of getting on it. i think its due to the Dyna s lobe not fitting snugly on the timing advancer. it seems to catch on the spring arms and not let them expand. If i just rev it a few times it resets the arms though. At least I think that is what the problem is.
1976 KZ750 hardtail
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
