Quick release spark plug...
- Becker
-
- Offline
- User
-

Registered
- The Doctor Will Rise Again
- Posts: 384
- Thanks: 1
Re: Quick release spark plug...
12 Dec 2010 22:29you will need to drill and tap the hole to use the helicoil or the timesert, so you will get chips in the cylinder you will need to get out.
I was thinking about this too. Is there any way to do this while the head is still on the motor?? I was thinking of something like turning the motor to TDC when both valves are open and hooking a shop vac to the exhaust side with the header and carbs off. Think that would work?? I don't need to do this but just for future reference.
78 KZ750B3
79 KZ400 LTD
78 KZ650C2
79 KZ650C3
78 KZ650B2A
80 KZ650F1
80 KZ650E1
81 CB750K Super Sport
79 KZ400 LTD
78 KZ650C2
79 KZ650C3
78 KZ650B2A
80 KZ650F1
80 KZ650E1
81 CB750K Super Sport
Please Log in or Create an account to join the conversation.
- cyclhed
-
- Offline
- User
-

Registered
- Posts: 56
- Thanks: 0
Re: Quick release spark plug...
17 Dec 2010 23:24
If I were going to try drilling and tapping it without pulling the head I would use a strong shop vac and hold the nozzle close as you drill and tap. Then flush out with a solvent (WD40) and compressed air. You should be able to get most of the chips out and the rest will blow out when start the engine! A little momentary AL dust won't hurt anything. I would also go with the Helicoil type because you remove less material. I would use some Loctite and remove the excess Loctite from the threads and let it dry before installing the spark plug for fear of sticking the heli-coil to the spark plug. Put anti seize on the plug threads so the insert stays in the head when you remove the plug. Should work if done properly. Let us know.
Past:
1972 175 F7
1974 KZ400
1981 GPZ550
1980 KZ750 LTD
1978 KZ1000
1968 H1500 Mach III
Present:
1982 KZ1000 M2 CSR
1972 175 F7
1974 KZ400
1981 GPZ550
1980 KZ750 LTD
1978 KZ1000
1968 H1500 Mach III
Present:
1982 KZ1000 M2 CSR
Please Log in or Create an account to join the conversation.
- mtbspeedfreak
-
- Offline
- User
-

Registered
- Posts: 1413
- Thanks: 36
Re: Quick release spark plug...
21 Dec 2010 00:59
The inaugural use of my new torque wrenches will be to torque down new sparkplugs. What's the torque spec for these? '76 KZ900 if it matters.
Thanks!
Thanks!
2000 ZRX 1100
1976 KZ 900- Daily Driver
1980 LTD 550- Dalton Highway survivor!
If it has tits or tires, it'll give you problems!
1976 KZ 900- Daily Driver
1980 LTD 550- Dalton Highway survivor!
If it has tits or tires, it'll give you problems!
Please Log in or Create an account to join the conversation.
- Kidkawie
-
- Offline
- User
-

Registered
- I bleed premix
- Posts: 1924
- Thanks: 246
Re: Quick release spark plug...
21 Dec 2010 09:53
kzrider.com/index.php?option=com_kunena&...w&catid=21&id=407699
:laugh:
Used these on one of my cars about 100k miles ago, Napa carries them: www.acehardwareoutlet.com/productdetails...80&source=GoogleBase
:laugh:
Used these on one of my cars about 100k miles ago, Napa carries them: www.acehardwareoutlet.com/productdetails...80&source=GoogleBase
1975 Z1 900
1994 KX250 Supermoto
2004 KX125
1994 KX250 Supermoto
2004 KX125
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Quick release spark plug...
21 Dec 2010 10:15
mtbspeedfreak wrote:
Hoping they're the genuine "Black Forest" brand.
18.5~22.0 ft-lbs
The inaugural use of my new torque wrenches will be to torque down new sparkplugs. What's the torque spec for these? '76 KZ900 if it matters. Thanks!
Hoping they're the genuine "Black Forest" brand.
18.5~22.0 ft-lbs
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: Quick release spark plug...
21 Dec 2010 15:57
If you happen to lose some debris into the cylinder, a length of carb vac hose held in the shop vac intake, can then be inserted through the plug hole and twisted around in the cylinder to suck up anything.
Works quite well.
Works quite well.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
- mtbspeedfreak
-
- Offline
- User
-

Registered
- Posts: 1413
- Thanks: 36
Re: Quick release spark plug...
03 Jan 2011 00:55 - 03 Jan 2011 00:55
Patton wrote:
Of course, AND I used elbow grease to lube the threads. I figured real grease would "carbonize" and make a mess of things.
mtbspeedfreak wrote:The inaugural use of my new torque wrenches will be to torque down new sparkplugs. What's the torque spec for these? '76 KZ900 if it matters. Thanks!
Hoping they're the genuine "Black Forest" brand.
18.5~22.0 ft-lbs
Of course, AND I used elbow grease to lube the threads. I figured real grease would "carbonize" and make a mess of things.
2000 ZRX 1100
1976 KZ 900- Daily Driver
1980 LTD 550- Dalton Highway survivor!
If it has tits or tires, it'll give you problems!
1976 KZ 900- Daily Driver
1980 LTD 550- Dalton Highway survivor!
If it has tits or tires, it'll give you problems!
Last edit: 03 Jan 2011 00:55 by mtbspeedfreak.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
