Head milling
- TomW
-
Topic Author
- Offline
- User
-

Registered
- Keep the blue side up.
- Posts: 502
- Thanks: 52
Re: Head milling
27 Feb 2011 20:29
larrycavan wrote:
The lowest spots are between the cylinders, 1&2 and 3&4.
The area around the chain tunnel is maybe .0015" low. I have APE studs on the way for crank and heads. The cam bearings look great, I don't think there was any misalignment there. Almost every measurement I made on the motor was within or very close to standard. Nothing close to service limits. I could probably bolt it up without milling the head and get away with it, but I'm going for maximum peace of mind and minimum cash outlay.
There was some oil seepage last spring but the head nuts were loose and when I re-torqued them the seepage stopped 99%.
Me too.APE Jay wrote:You might want to have caution when milling a warped ohc cylinder head. If the head is bowed end for end, you shouldn't cut it. The reason is, that the cam bores are machined parallel to the head surface. If the head gets bowed or warped on the surface, then the cam bores are also. If you precede to machine the surface flat again, the cam bores are then permanently out of alignment.
What to do? We have taken bowed heads in the press and pushed them back to within a thou or two, Good cylinder studs take care of the rest and pull it down flat and the cam bores are once again in line.
I've seen car heads like bananasNever saw a Kawasaki head like that though. Sometimes they'll be low on one corner....sometimes in between to chambers....sometimes in several random spots. It varies. If there's any problem with journals being out of alignment you'll find that quick enough by spinning the cams.
I've watched car heads be straightened. They use a plate and put them in an oven. Never saw anyone press one though.... whew, I'd be scared to press on one myself...
The lowest spots are between the cylinders, 1&2 and 3&4.
The area around the chain tunnel is maybe .0015" low. I have APE studs on the way for crank and heads. The cam bearings look great, I don't think there was any misalignment there. Almost every measurement I made on the motor was within or very close to standard. Nothing close to service limits. I could probably bolt it up without milling the head and get away with it, but I'm going for maximum peace of mind and minimum cash outlay.
There was some oil seepage last spring but the head nuts were loose and when I re-torqued them the seepage stopped 99%.
'78 KZ1000B2 LTD stock + Vetter Fairing & luggage
'91 ZG1200B5 Voyager XII, stock
'91 ZG1200B5 Voyager XII, stock
Please Log in or Create an account to join the conversation.
- TomW
-
Topic Author
- Offline
- User
-

Registered
- Keep the blue side up.
- Posts: 502
- Thanks: 52
Re: Head milling
27 Feb 2011 20:32
'78 KZ1000B2 LTD stock + Vetter Fairing & luggage
'91 ZG1200B5 Voyager XII, stock
'91 ZG1200B5 Voyager XII, stock
Please Log in or Create an account to join the conversation.
- Old Man Rock
-
- Offline
- User
-

Registered
- Posts: 6071
- Thanks: 225
Re: Head milling
28 Feb 2011 03:46 - 28 Feb 2011 03:47
"guy cant check air in his own tires "...
Hey, I know how to check the air... I go to the dealership and ask them hot shot kid mechanics to check and fill them for me.... :blush:
Not sure why it costs so much to do so but worth every penny of it...
And Larry... "I use a .000" feeler gauge for that "... Assumption is that would be your Mr. Happy tool? :blink:
Hey, I know how to check the air... I go to the dealership and ask them hot shot kid mechanics to check and fill them for me.... :blush:
Not sure why it costs so much to do so but worth every penny of it...
And Larry... "I use a .000" feeler gauge for that "... Assumption is that would be your Mr. Happy tool? :blink:
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
Last edit: 28 Feb 2011 03:47 by Old Man Rock.
Please Log in or Create an account to join the conversation.
- Jeff.Saunders
-
- Offline
- Vendor
-

Vendors
- Posts: 1238
- Thanks: 149
Re: Head milling
28 Feb 2011 06:41
Jay's post about the cam line boring is a key point.
I know what the factory manuals state for acceptable head warpage. But if you install heavy-duty cylinder studs, and torque the head down more, how much warpage can be corrected without machining?
I know what the factory manuals state for acceptable head warpage. But if you install heavy-duty cylinder studs, and torque the head down more, how much warpage can be corrected without machining?
Please Log in or Create an account to join the conversation.
- BSKZ650
-
- Offline
- User
-

Registered
- Posts: 2061
- Thanks: 14
Re: Head milling
28 Feb 2011 08:55
something I have not seen mentioned is the gasket thickness and how much it can take up for a head not being flat. Jeff is right on about the cam bores, I have seen that messed up many times on car heads, never saw a bike head that far off to create a bearing issue.
on any alum head, I used to bolt them to a 1 1/2 inch steel plate that was flat, heat the head and plate in a oven and then slowly bring the temp down, if that didnt work the first time, then I would add shim stock to the high area and repeat the process.
after doing that, I dont think I ever took more than .010 off any alum head
on any alum head, I used to bolt them to a 1 1/2 inch steel plate that was flat, heat the head and plate in a oven and then slowly bring the temp down, if that didnt work the first time, then I would add shim stock to the high area and repeat the process.
after doing that, I dont think I ever took more than .010 off any alum head
77 kz650, owned for over 25 years
77 ltd1000, current rider
76 kz900, just waiting
73 z1,, gonna restore this one
piglet, leggero harley davidson
SR, Ride captian, S.E.Texas Patriot Guard Riders.. AKA KawaBob
77 ltd1000, current rider
76 kz900, just waiting
73 z1,, gonna restore this one
piglet, leggero harley davidson
SR, Ride captian, S.E.Texas Patriot Guard Riders.. AKA KawaBob
Please Log in or Create an account to join the conversation.
- APE Jay
-
- User
-

Public
- Thanks: 0
Re: Head milling
28 Feb 2011 17:11
So I am assuming that you guys never saw a Nyberg pro stock head, where they took the seats out, machined a huge V down the center on top, end to end, then heated it up, clamped it up in a press to force the V closed, then welded the whole thing up.
Then machine the deck flat again, then send it to the late Elmer Trett to have the cam bores line honed so cams would turn in it again.
This was done to spread the valve angels out to they could run those giant valves.
That was the state of the art deal back in the day, and VERY expensive.
Then machine the deck flat again, then send it to the late Elmer Trett to have the cam bores line honed so cams would turn in it again.
This was done to spread the valve angels out to they could run those giant valves.
That was the state of the art deal back in the day, and VERY expensive.
Please Log in or Create an account to join the conversation.
- PLUMMEN
-
- Offline
- User
-

Registered
- Posts: 7983
- Thanks: 104
Re: Head milling
28 Feb 2011 17:17
:blink: little out of my skill/price range jay! :laugh:
Still recovering,some days are better than others.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
