Acceleration issues! Help!

  • Soulmighty
  • Soulmighty's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 29
  • Thanks: 0

Acceleration issues! Help!

04 Mar 2011 10:21
#434949
Hello all,
I just took my bike out after being winterized and a funny thing is happening when I gun it. I can be in any gear and if I really kick it up in that same gear the engine revs beyond what appears to be transferring to the sprocket. Almost like it's not egaging the chain but ONLY when I really kick it up. What's going on here? It's never happened before. Do I need to simply tighten the sprocket? Help! Other than that, it runs great..

Thanks,

Dave

Please Log in or Create an account to join the conversation.

  • hocbj23
  • hocbj23's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Acceleration issues! Help!

04 Mar 2011 10:28
#434952
clutch slipping?When u winterized it did u put any additives in the oil that might have coated the clutch plates and made them more slippery?Did u change the oil and filter before cranking it up? If not,would advise an oil and filter change and be sure the clutch is properly adjusted.bj

Please Log in or Create an account to join the conversation.

  • tinlizzie37
  • tinlizzie37's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 149
  • Thanks: 1

Re: Acceleration issues! Help!

04 Mar 2011 10:29
#434953
Hi Dave, sounds like a clutch issue. Lube the cable then check for proper adjustment. May be time for new clutch parts. Bob
Bob KZ 650 E1, En 450

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Acceleration issues! Help!

04 Mar 2011 11:11
#434960
A routine clutch push rod adjustment might totally resolve the issue.

Including information about bike year and model may elicit better responses. And it's easy to put in your signature where it will automatically appear in posted messages.
When done, the signature information appears in all posts, past and future. And may be changed as often as desired.

Here's how to do it:
Click > Adding Info to Signature

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Acceleration issues! Help!

04 Mar 2011 11:34
#434966
sounds like the clutch. The springs get weak over time.
1979 KZ-750 Twin

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Acceleration issues! Help!

04 Mar 2011 11:42
#434970
Clutch push rod adjustment -- Need and Purpose
[This is a 1 minute job from start to finish, maybe 2 minutes the first time.]

The FSM covering Z1 and KZ900 includes a periodic maintenance chart requiring clutch push rod adjustment at 2000 mile (3000 km) intervals and explains the need therefor in separate text, which explanation is quoted verbatim as follows:

Besides cable stretch, clutch plate wear also causes the clutch to go out of adjustment, with a decrease in push rod play. Due to this wear, the push rod gradually moves closer to the clutch release lever (at the lower end of the clutch cable) until it touches the adjusting screw. When the rod is touching the screw and therefore has no play, the clutch will not engage fully and clutch slippage will occur. Note that the clutch push rod does not necessarily have play just because the clutch hand lever has play, and so hand lever play alone cannot be used to determine whether or not the clutch requires adjustment.


The FSM covering '77-'79 KZ1000's includes a periodic maintenance chart requiring clutch adjustment at 5000 km intervals, and explains the need therefor in slightly different language, which explanation is quoted verbatim as follows:

Clutch plate wear also causes the clutch to go out of adjustment. This wear causes the play between the push rod and the adjusting screw to gradually diminish until the push rod touches the adjusting screw. When this play is lost, the clutch will not engage fully, causing the clutch to slip.
NOTE: Even though the proper amount of play exists at the clutch lever, clutch lever play alone cannot be used to determine whether or not the clutch requires adjustment.

end of excerpt


While the clutch may indeed be worn out with plates needing replacement, it isn't uncommon to overlook or be unaware of the clutch push rod adjustment feature, especially without a manual. It is worrisome to see anyone of unknown experience, without a manual or failing to consult a manual, proceed with clutch disassembly and plate replacement, without first being aware of and considering the clutch push rod adjustment.

Where both (1) clutch cable slack adjustment is perfect, and (2) clutch push rod adjustment is perfect, and the clutch still slips, suspicion is certainly toward the plates being worn and needing replacement. But other things can also cause slippage, even with proper adjustments and good plates, such as glazed plates or improper oil being used in the crankcase.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • Soulmighty
  • Soulmighty's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 29
  • Thanks: 0

Re: Acceleration issues! Help!

04 Mar 2011 19:08
#435071
Thanks very much everyone. I love a consensus! I'll check the clutch tomorrow. Thanks again! In case you were wondering, I have a Z1 Classic converted to carbs (77 KZ1000 carbs) and customized. Here's a pic.. :-)

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Acceleration issues! Help!

05 Mar 2011 02:25
#435105
Routine clutch push rod adjustment.

Assure having some "slop" in the clutch cable, using adjustments at the handlebar lever perch and at mid-cable along left frame down tube near the exhaust header.

Removing the access plate should reveal the adjustment screw and locknut.

First, slightly loosen the locknut.

The hidden end of the screw interfaces with the pushrod.

The basic idea is to lightly seat the screw against the pushrod, then back the screw 1/4 turn away from the pushrod, to thereby provide a small gap between end of screw and pushrod.

Here's a possible snag ---
The screw is part of an actuator assembly.
On some designs (screw-type), the screw turns clockwise to seat before turning counter-clockwise to provide the gap.
On other designs (ball and ramp), the screw turns counter-clockwise to seat before turning clockwise to provide the gap.

Will now speculate that the bike at hand has the ball and ramp style, whereby the screw turns counter-clockwise to seat before turning clockwise to provide the gap. But I might be wrong. So if it doesn't work that way, adjust it the other way.

Remember to snug the locknut before finishing. Just snug is plenty tight enough.

Lastly, reduce "slop" in the cable to produce desired amount of free play in the lever at the perch.

Good Fortune! :)

[Click on image to enlarge view.]

1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Acceleration issues! Help!

05 Mar 2011 02:38
#435106
With the clutch lever released (not being squeezed), the clutch is supposed to be fully engaged (plates pressed tightly together).
If the gap isn't there, the plates can't fully press together, which causes the clutch to "slip."

With the clutch lever squeezed, the clutch plates are supposed to be separated. When squeezed, the gap disappears and the push-rod is pressed inward to press the plates apart, overcoming the spring pressure, and thereby disengaging the clutch.

Too much gap wastes clutch lever movement as too much lever travel is expended to simply close the gap before starting pressure against the push-rod. Whereby the clutch may only partly disengage when the lever is fully squeezed, and produce the sensation of a "sticky" or "grabby" clutch.

Way too much gap may waste all the clutch lever movement, as all the lever travel is expended to simply close the gap, with no movement left to exert pressure against the push-rod.

No gap or too little gap may over-stress the actuator assembly when the clutch lever is squeezed and cause the actuator assembly to pop apart.

It's important to know exactly how to set the required gap.
The general rule is to lightly close the gap, then back off ¼~½ turn.
On some models the gap is closed by turning the adjustment screw clockwise. But on other models the gap is closed by turning the adjustment screw counter-clockwise.

Mistaking which direction to turn the adjustment screw could for example start with the gap wide open instead of lightly seated.

The simplified illustration in the former post helps visualize what is supposed to happen as the mechanisms engage and disengage the clutch.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • stonemaster
  • stonemaster's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Acceleration issues! Help!

05 Mar 2011 02:51
#435108
nice bike man

Please Log in or Create an account to join the conversation.

  • ed spangler
  • ed spangler's Avatar
  • Offline
  • User
  • User
    Registered
  • Tennessee Z
  • Posts: 512
  • Thanks: 29

Re: Acceleration issues! Help!

05 Mar 2011 03:24
#435110
Very Nice Bike!!
Have 1975 Kawasaki Z1-B & 2003 Harley Davidson Heritage Softail Classic
Had Hondas, Harleys and many ,many Z Series Kaws both Std. & LTD's

Please Log in or Create an account to join the conversation.

  • Soulmighty
  • Soulmighty's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 29
  • Thanks: 0

Re: Acceleration issues! Help!

05 Mar 2011 04:10
#435112
Thanks guys!

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum