completely dumbfounded........

  • murr50
  • murr50's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 105
  • Thanks: 3

Re: completely dumbfounded........

17 Jun 2011 12:23
#457768
ok, i assumed i would have to take the timing plate off. When i get home from work, i will remove it and see if anything is sheered. I read online something about woodruff keys.. does a 77 kz650 have one of these? is it possible that this is broken and may cause the problem?

also, i am aware of the 17 vs 14 mm nuts. i have been using the 17mm nut to crank the engine
1977 kz650 C

Please Log in or Create an account to join the conversation.

  • steell
  • steell's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6849
  • Thanks: 208

Re: completely dumbfounded........

17 Jun 2011 13:58
#457784
Lou has it exactly right, it's a roll pin not a woodruff or any other kind of key.
And you're not the first person to shear one.
KD9JUR

Please Log in or Create an account to join the conversation.

  • kawsakiman
  • kawsakiman's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1246
  • Thanks: 6

Re: completely dumbfounded........

17 Jun 2011 19:05
#457843
can you bump it with the starter?
someday i will be able to afford my kz habit.

Please Log in or Create an account to join the conversation.

  • murr50
  • murr50's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 105
  • Thanks: 3

Re: completely dumbfounded........

17 Jun 2011 19:59
#457863
ok so i had a small breakthrough... i removed the timing plate and saw nothing wrong, so i took off the valve covers and took out the cam shafts.. turns out the chain was caught on something.. pistons move freely now...

NEW PROBLEM:

when i put the timing plate back on, im affraid i didnt line it up perfect. So now i dont know exactly where TDC is... now i can just look down the spark plug holes and sort of guess where TDC is, but i would rather have this exact. Any tricks to finding TDC without any markings?
1977 kz650 C

Please Log in or Create an account to join the conversation.

  • KZ250LTD
  • KZ250LTD's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1311
  • Thanks: 16

Re: .

17 Jun 2011 21:01 - 13 Feb 2012 18:23
#457871
.
79 KZ1000ST
Past:
Many.
Last edit: 13 Feb 2012 18:23 by KZ250LTD.

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: completely dumbfounded........

17 Jun 2011 22:10
#457888
murr50 wrote: ok so i had a small breakthrough... i removed the timing plate and saw nothing wrong, so i took off the valve covers and took out the cam shafts.. turns out the chain was caught on something.. pistons move freely now...

NEW PROBLEM:

when i put the timing plate back on, im affraid i didnt line it up perfect. So now i dont know exactly where TDC is... now i can just look down the spark plug holes and sort of guess where TDC is, but i would rather have this exact. Any tricks to finding TDC without any markings?

For those of us that are slow, please run this by us again. You stated earlier that the crankshaft was turning freely but the pistons were not moving (which still seems impossible to me). Now you state the cam chain was caught on something. Help me understand how a cam chain caught on something would allow the crankshaft to turn and prevent the pistons from moving? :unsure: Also, how can you put the "timing plate" (I assume you mean advancer) on but not lined up perfectly? it would either be correct or 180* out wouldn't it?
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)

Please Log in or Create an account to join the conversation.

  • murr50
  • murr50's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 105
  • Thanks: 3

Re: completely dumbfounded........

17 Jun 2011 22:22
#457890
ok so i am thinking that the timing advance bolt was not snug tight, so when the chain got caught, the bolt was just cranking and not moving anything... as for the timing advancer, it doesnt have a pin.... it must have broken in the past or something.. for this reason i needed to know how to find TDC... I think i have passed that hurdle as well though. But now of course theres something else...

Ihad a perfect spark before all this began, and now i only get a spark when i turn the ignition swith off... did a ground get disconnected or something?
1977 kz650 C

Please Log in or Create an account to join the conversation.

  • kzzoid
  • kzzoid's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 3
  • Thanks: 1

Re: completely dumbfounded........

17 Jun 2011 22:48
#457897
the timing advancer should be mounted on a pin on the end of the crankshaft, you can also look into the cylinder and have cylinder 1 and 4 at the top. as far as your electrical problem, check your fuses and make sure you didn't mix up the plug wires
kz1000,zx11,kx500

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: completely dumbfounded........

17 Jun 2011 23:59 - 18 Jun 2011 00:00
#457920
murr50 wrote: ... as for the timing advancer, it doesnt have a pin.... it must have broken in the past or something.. for this reason i needed to know how to find TDC... I think i have passed that hurdle as well though. But now of course theres something else...

You need to replace the pin. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Last edit: 18 Jun 2011 00:00 by 650ed.

Please Log in or Create an account to join the conversation.

  • andy9802gt
  • andy9802gt's Avatar
  • Offline
  • User
  • User
    Registered
  • If it tastes that good, eat it yourself.
  • Posts: 695
  • Thanks: 19

Re: completely dumbfounded........

18 Jun 2011 02:21
#457949
650ed wrote:
murr50 wrote: ... as for the timing advancer, it doesnt have a pin.... it must have broken in the past or something.. for this reason i needed to know how to find TDC... I think i have passed that hurdle as well though. But now of course theres something else...

You need to replace the pin. Ed


No. It's okay. It was running fine without it. I don't have .40 for such trivial shit.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm

Please Log in or Create an account to join the conversation.

  • KZ250LTD
  • KZ250LTD's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1311
  • Thanks: 16

Re: .

18 Jun 2011 03:18 - 13 Feb 2012 18:22
#457953
.
79 KZ1000ST
Past:
Many.
Last edit: 13 Feb 2012 18:22 by KZ250LTD.

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: completely dumbfounded........

18 Jun 2011 08:09
#457962
KZ250LTD wrote: Go to your Kawi dealer and order part # 555A0408
That is your pin, it is still in use today. If it costs you $5 that is about $495 cheaper than if you set your cams/timing wrong because you couldn't find TDC and bend all your valves

X2 U NEED THAT PIN.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum