cams and lash
- markosportsbikes
-
Topic Author
- Offline
- User
-

Registered
- Posts: 16
- Thanks: 0
Re: cams and lash
20 Aug 2011 18:12
yes motorhead i do hey guys i realy realy appreciate your time on this topic like isaid i checked all tolarances
Please Log in or Create an account to join the conversation.
- markosportsbikes
-
Topic Author
- Offline
- User
-

Registered
- Posts: 16
- Thanks: 0
Re: cams and lash
20 Aug 2011 18:21
i did that a few days ago thats why i posted my problem because i checked height on all valves tore head apart several times to make sure every thing is correct walked away from it for a day or two because my head hurt i took it apart again wile we have been chating i measured all lobes on both range are from 1.506 to1. 1.484 in inches witch is 38.32 in mm
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: cams and lash
20 Aug 2011 18:29 - 20 Aug 2011 18:33wireman wrote:my J manual says basically the same, 37.20-38mm = acceptable/ normal.Motor Head wrote:according to ma kaw 37.17 on the low end to 38.06 maxwireman wrote: did somebody sell you j motor valves?[/quote
This where I was asking about the Installed height.
have you got the spec there for him, wireman?
I have the J manual, not the KZ.
This is for the Valve Installed Height.
Please check this measurement and Post the result.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 20 Aug 2011 18:33 by Motor Head.
Please Log in or Create an account to join the conversation.
- markosportsbikes
-
Topic Author
- Offline
- User
-

Registered
- Posts: 16
- Thanks: 0
Re: cams and lash
20 Aug 2011 18:32
hey guys i am going to measur all valves again make sure i did not make mistake.i could have been tited
Please Log in or Create an account to join the conversation.
- markosportsbikes
-
Topic Author
- Offline
- User
-

Registered
- Posts: 16
- Thanks: 0
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: cams and lash
20 Aug 2011 19:07
If by chance you still have the OLD Exhaust valves that were in that head, you could compare stem lengths, etc.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- cavanaughracing
-
- Offline
- User
-

Registered
- Posts: 213
- Thanks: 25
Re: cams and lash
20 Aug 2011 22:22 - 21 Aug 2011 08:41
Is the exhaust cam a 1.110" base circle?
Do you know how to measure that?
Installed height must be checked with the spring seat removed. That requires pulling the valve seals too. You want to be at 1.475" - 1.485" to be in a good shim adjustment range.
You likely have either:
a] small base circle cam
b] bent exhaust valves
c] exhaust valves were tipped a bunch
Or any combination of a,b,c.
Those cams have a ton of duration = lot's of TDC overlap lift = greater possibility of bending valves if you get them installed a pin off from where they should be.
Generally you won't bend all 4 exhaust valves because things will bind long before you turned the motor over enough times to nail all 4.
Another thing you can run into is bucket thickness variances. Some of the aftermarket buckets were made aproximately 8 shim sizes thicker than they once were. So, if the head was originally setup for thicker buckets and you now are trying to use OEM SOB buckets, that could account for the problem.
If you are going that route, it's a mistake IMO. Stock buckets with performance valve springs is a poor choice. They will go south on you. Maybe not this week but eventually
Do you know how to measure that?
Installed height must be checked with the spring seat removed. That requires pulling the valve seals too. You want to be at 1.475" - 1.485" to be in a good shim adjustment range.
You likely have either:
a] small base circle cam
b] bent exhaust valves
c] exhaust valves were tipped a bunch
Or any combination of a,b,c.
Those cams have a ton of duration = lot's of TDC overlap lift = greater possibility of bending valves if you get them installed a pin off from where they should be.
Generally you won't bend all 4 exhaust valves because things will bind long before you turned the motor over enough times to nail all 4.
Another thing you can run into is bucket thickness variances. Some of the aftermarket buckets were made aproximately 8 shim sizes thicker than they once were. So, if the head was originally setup for thicker buckets and you now are trying to use OEM SOB buckets, that could account for the problem.
If you are going that route, it's a mistake IMO. Stock buckets with performance valve springs is a poor choice. They will go south on you. Maybe not this week but eventually
Larry C.
cavanaughracing.com
cavanaughracing.com
Last edit: 21 Aug 2011 08:41 by cavanaughracing.
The following user(s) said Thank You: wireman
Please Log in or Create an account to join the conversation.
- cavanaughracing
-
- Offline
- User
-

Registered
- Posts: 213
- Thanks: 25
Re: cams and lash
21 Aug 2011 13:42 - 21 Aug 2011 13:43Attachment andrews-COMPARE.jpg not found
Have a look at this...
See the TDC lift?
Look at the 3x, 8x & 5x grinds. Notice the TDC lift at their particular lobe centers.
Notice how the 4x is listed with a 5 degree wider spread than the 3x but still yields significant lift at overlap. Pull a 106 center on a 4x and you'll have more TDC lift than the 3x on the same center.
So, as you can see, you need to be paying close attention to setup
If you get the 4x exhaust cam 1 pin late in the timing, the valves might tangle at TDC overlap. It doesn't take much to bend one.
In situations where you have a serious lobe to contend with, it's handy to setup the head with light springs when you degree the cams. That way you can push the valves open and watch your indicator travel to see how cozy the parts are getting to each other.
In any case, with a lobe like that, you need to really be paying attention to the details.
Larry C.
cavanaughracing.com
cavanaughracing.com
Last edit: 21 Aug 2011 13:43 by cavanaughracing.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
