Compression reading?

  • garyprather
  • garyprather's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 133
  • Thanks: 0

Compression reading?

28 Aug 2011 09:47
#472296
I have my 1983 spectre running well now and I was wondering if 200psi on the compression test is correct for a bike that has 20k miles on it. I have put 2k since I purchased the bike. I have no clue if it was rebuilt. I am thinking that the bike stock should only have around 165 or so. Would boring it out in the past up the compression that much. Or is it Just a rebuild that takes along time to start dropping . Is there any ways to telling if someone changed it without tearing the engine apart. I will have a look at the cams this fall when in to check valve clearance. I checked the bike when it was cold a few weeks back and got 185psi I believe was my lowest reading.

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Compression reading?

28 Aug 2011 10:14 - 28 Aug 2011 11:03
#472301
Is that a Trusted Gauge? This would be high of course. It is possible that there is carbon built up on the crown of the piston, and the Combustion Chamber. This will raise the #'s some.
Can you take the plugs out and look at the top of the pistons, to gauge the build up. Some is normal, but excessive is no good. There are combustion chamber cleaners on the market. They do what they advertise and get rid of the carbon. Also a small slow steady delivery of water into the intake at a good RPM, like around 4K, will cause steam in the chamber. That will get rid of the carbon also, and clean the Ex ports.
Member Otakar has a thread somewhere around last year on Cleaning the Carbon, and different chemicals/ methods. Here is one: kzrider.com/forum/2-engine/369254-piston-top-cleaning
you can also Google the process as it is an issue in most internal combustion motors.

Also I just thought that with your other Mods by the Po, maybe he put Pop Up pistons in it. Looking from the plug hole see if there is just the basic round dome, or if there is a Pop Up.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 28 Aug 2011 11:03 by Motor Head.

Please Log in or Create an account to join the conversation.

  • garyprather
  • garyprather's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 133
  • Thanks: 0

Re: Compression reading?

28 Aug 2011 11:09
#472307
there is vary little carbon at all just the normal. I thought it was carbon build up until I took a peak. I have done the water trick before on cars and trucks. The pistons look normal to me, just a basic dome piston no cut out for valves and such. I am not understanding why it so high.

Please Log in or Create an account to join the conversation.

  • garyprather
  • garyprather's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 133
  • Thanks: 0

Re: Compression reading?

28 Aug 2011 11:47
#472313
I have tested with different gauges also same readings.

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Compression reading?

28 Aug 2011 12:17
#472318
Any engine "pinging" noise when accelerating or under load?

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Compression reading?

28 Aug 2011 12:20
#472319
:unsure: If "rebuilt," perhaps the head was shaved and/or base gasket eliminated.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • garyprather
  • garyprather's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 133
  • Thanks: 0

Re: Compression reading?

28 Aug 2011 12:53
#472322
No ping at all it sounds good. I have no clue how much power these bikes should have either. I know it a zippy bike. So i cannot do a comparison. I know that it wont hesitate to pull the front tire off the ground while rolling at 10 to 15 mph. Are all the 1100 spectres like that?

Please Log in or Create an account to join the conversation.

  • garyprather
  • garyprather's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 133
  • Thanks: 0

Re: Compression reading?

28 Aug 2011 12:55
#472323
I can see the head gasket there if that s the gasket you are referring to. is there a way to tell if that was done without disassembling?

Please Log in or Create an account to join the conversation.

  • etbike3135
  • etbike3135's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 379
  • Thanks: 50

Re: Compression reading?

28 Aug 2011 16:08
#472346
Sounds like it may have a piston kit. Its about right for a 10 to 1 and maybe even the head was milled. If you pull the tire just rolling on its got something done to it. You can look down a spark plug hole with an led light and see what the dome of the pistons looks like. A generally flat but curved piston is stock but if the middle pops up and you have big valve pockets tehn they are after market.
The motor should get plenty hot also when riding, where you can even feel waves of heat coming up at you.
1973 Kawasaki Z1
18 years in dragbikes

Please Log in or Create an account to join the conversation.

  • garyprather
  • garyprather's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 133
  • Thanks: 0

Re: Compression reading?

28 Aug 2011 18:43
#472356
I did look in the sparkplug hole and the pistons seem to be stock. Slighty domed and no valve pockets. Maybe the head was shaved is there a way to tell if it was. I will be pulling the cover to check valves this fall and I should be able to check cams also. I have ordered oversized pistons for atvs and such they had stampings on the top that said how much over it was. Are aftermarket pistons for these bikes the same? the only thing I see is the arrow pointing forward right now. Did the sock pistons have the arrow on them or just oem.

Please Log in or Create an account to join the conversation.

  • etbike3135
  • etbike3135's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 379
  • Thanks: 50

Re: Compression reading?

28 Aug 2011 20:44
#472378
Stock pistons do have the arrow. The easiest way to tell if the head is milled is to line up the cam timing marks. If it looks like the TDC and the mark on the cam gear don’t line up the way the manual shows most likely on the J bikes (because the hyvo chains don’t stretch like the peanuts do) its because the head was milled and now the cam timing is off.
1973 Kawasaki Z1
18 years in dragbikes

Please Log in or Create an account to join the conversation.

  • garyprather
  • garyprather's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 133
  • Thanks: 0

Re: Compression reading?

28 Aug 2011 22:08
#472403
When I get inside this fall I will have to take a look. I was thinking of putting in a set of hotter cams nothing real aggressive but just to add more zip is all.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum