BLOCK BORE
- etbike3135
-
- Offline
- User
-

Registered
- Posts: 379
- Thanks: 50
Re: BLOCK BORE
10 Nov 2011 16:39
Here is the bottom of a stock block. See the extra holes that are filled with rubber plugs? Even if the top case has only been bored to accept a 1260 sleeve these holes will come into the top case bore.
1973 Kawasaki Z1
18 years in dragbikes
18 years in dragbikes
Please Log in or Create an account to join the conversation.
- 531blackbanshee
-
- Offline
- Vendor
-

Vendors
- Posts: 7442
- Thanks: 796
Re: BLOCK BORE
10 Nov 2011 16:52etbike3135 wrote: Here is the bottom of a stock block. See the extra holes that are filled with rubber plugs? Even if the top case has only been bored to accept a 1260 sleeve these holes will come into the top case bore.
it does look as tho a copper base gasket would seal it up tho.
or would it not?
leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: BLOCK BORE
10 Nov 2011 17:35
i dont see the problem, why would they leak? with the thinner mating surface, wouldn’t u get more pressure applied to the gasket with the same torque on the bolts? I don’t see how the cyl holes u speak of, come into play?
educate me too.
educate me too.
Attachment z1casesboredto83mm.jpg not found
Attachment stockcyl.jpg not found
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: BLOCK BORE
10 Nov 2011 17:40
are u saying that those holes will now open up into the new bore when u put them together?
i have a 1428 case set up, in the shop but i dont have a spare cyl to place on it to see if they align .
i have a 1428 case set up, in the shop but i dont have a spare cyl to place on it to see if they align .
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- etbike3135
-
- Offline
- User
-

Registered
- Posts: 379
- Thanks: 50
Re: BLOCK BORE
10 Nov 2011 19:55
Yes, the extra holes in a stock block will open up into the case bore. I should not sound so harsh on this subject because I did make mine work. I made aluminum plugs for the extra holes and pressed them in flush. I do believe I then used a copper gasket. This is on a drag motor and only sees minutes of run time which keep the leaks to a minimum. After I went through this I vowed to never bore a set of cases more then I needed to again.
1973 Kawasaki Z1
18 years in dragbikes
18 years in dragbikes
Please Log in or Create an account to join the conversation.
- JEFFG1
-
Topic Author
- Offline
- User
-

Registered
- Posts: 341
- Thanks: 16
Re: BLOCK BORE
10 Nov 2011 20:21
well now what to do ? i guess i will just have mine bored for my jug. i was just looking ahead in case i wanted to go bigger i had the op. to do so.
1976 KZ 900 PRO STREET 1977 kz1000 dragbike project
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: BLOCK BORE
11 Nov 2011 17:59
there are basicaly 4 sizes.
1. stock 903 jogs
2. 903 cases with 1015 jugs
3.1200 cc sleeves in stock cyl block.
4. big block sleeve which can be bored for 1327cc or 1428cc.
so will be fine untill u jump to a big block.
once u have the cases bored for a big block u cannot go back to the stock barrels. unless u block the holes in the stock barrels as noted in the info above.
1. stock 903 jogs
2. 903 cases with 1015 jugs
3.1200 cc sleeves in stock cyl block.
4. big block sleeve which can be bored for 1327cc or 1428cc.
so will be fine untill u jump to a big block.
once u have the cases bored for a big block u cannot go back to the stock barrels. unless u block the holes in the stock barrels as noted in the info above.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- 531blackbanshee
-
- Offline
- Vendor
-

Vendors
- Posts: 7442
- Thanks: 796
Re: BLOCK BORE
13 Nov 2011 03:24
thanks for the clarification ! 
leon
leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
Please Log in or Create an account to join the conversation.
- JEFFG1
-
Topic Author
- Offline
- User
-

Registered
- Posts: 341
- Thanks: 16
Re: BLOCK BORE
14 Nov 2011 11:49 - 14 Nov 2011 11:51
i just got a 1230 and i am going to have the case bored for it that way everything should be good.
1976 KZ 900 PRO STREET 1977 kz1000 dragbike project
Last edit: 14 Nov 2011 11:51 by JEFFG1.
Please Log in or Create an account to join the conversation.
- APE Jay
-
- User
-

Public
- Thanks: 0
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: BLOCK BORE
14 Nov 2011 20:44APE Jay wrote: Be sure they bore it on location
Jay - do you mind elaborating for those of us who's stupid? :whistle:
Please Log in or Create an account to join the conversation.
- etbike3135
-
- Offline
- User
-

Registered
- Posts: 379
- Thanks: 50
Re: BLOCK BORE
14 Nov 2011 20:48
He means in relation to the dowel pins with the correct spacing. Dont just say hey this looks like the right spot!
1973 Kawasaki Z1
18 years in dragbikes
18 years in dragbikes
The following user(s) said Thank You: DoubleDub
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
