KZ bore&hone

  • Breaker19
  • Breaker19's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 88
  • Thanks: 2

Re: KZ bore&hone

18 Jan 2012 20:21
#498723
les holt wrote: This gets used quite a bit too. B)


Attachment millersyncrowave250.jpg not found




Les

OK, now you're just showin' off.. ;)
2003 Suzuki DR650 Dual-Sport
1982 KZ1100A2 - GONE! Traded-in for a '12 Concours 14
www.facebook.com/pages/Moto-Resto/169238286503527

Please Log in or Create an account to join the conversation.

  • les holt
  • les holt's Avatar
  • Offline
  • Vendor
  • Vendor
    Registered
  • Posts: 1633
  • Thanks: 286

Re: KZ bore&hone

18 Jan 2012 20:32
#498728
Yeah I was. :whistle: I'm in the shop right now and a little bored, one of those days of so much to do and where to start. Sitting at this sea of glass isn't helping. :blush:

Les

Please Log in or Create an account to join the conversation.

  • jeffasaki
  • jeffasaki's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 996
  • Thanks: 44

Re: KZ bore&hone

18 Jan 2012 20:37
#498729
les holt wrote: This gets used quite a bit too. B)


Attachment millersyncrowave250.jpg not found




Les[/quote
hopfully not anywhere near a honed cylinder
78 Z1R
78 KZ1000
76 KH500 gone
71 HS1B 90
81 GS 1100 gone
80 PE400
02 KLR


Ontario Canada

Please Log in or Create an account to join the conversation.

  • APE Jay
  • APE Jay's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: KZ bore&hone

19 Jan 2012 19:27
#498948
There seems to be a mindset that these are 35 year old motors with 35 year old metal, so it is OK to use 35 year old technology to rebore them. What you arte not taking into consideration, is if you are putting a Wiseco 1075 or some other US made piston, you are not going to be using old school materials.

You will be using the very latest piston alloys, and more important, you will be using start of the art piston rings, that are way different than what these motors came with in the 70s.

Please Log in or Create an account to join the conversation.

  • andy9802gt
  • andy9802gt's Avatar
  • Offline
  • User
  • User
    Registered
  • If it tastes that good, eat it yourself.
  • Posts: 695
  • Thanks: 19

Re: KZ bore&hone

19 Jan 2012 20:41
#498960
LarryC wrote: FWIW :) I've had blocks in my hands that were bored by APE. Nice job, measured up good and unlike most places....they put the correct chamfer on the bottom of the sleeves so it assembles easily. And I mean EASILY.

Larry C

That is the exact reason there are things you shouldn't go cheap on. When you send things to someone that specializes in them you get experience that is worth more than any mark up involved. I'm sure a local, less experienced shop could do it I'm not willing to pay them to practice on my stuff.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm
The following user(s) said Thank You: BlackZ1R

Please Log in or Create an account to join the conversation.

  • BlackZ1R
  • BlackZ1R's Avatar
  • Offline
  • User
  • User
    Registered
  • Kawasaki in my blood
  • Posts: 700
  • Thanks: 47

Re: KZ bore&hone

20 Feb 2012 01:13
#505187
jeffasaki wrote: all you need is a mill
with a feed table
I know this is a month old, but still worth commenting on. I wouldn't trust just any shop to do a motorcycle cylinder. Try running a dial gauge through the bore and see what kind of run out and roundness you get from your local guy. Then check one of APE's or Pit Stop's bore jobs. I guarantee you will see a difference.

These guys know what it takes to get a cylinder bored and honed, STRAIGHT and ROUND, to get maximum sealing and performance for you engine. You don't want egg shaped or out of square bores in your air cooled Z motors.

As far as a mill is concerned, sure, you can bore cylinders on one, but you have a lot of room for error. Let the pros do it on the correct equipment and you'll be money ahead.

:whistle:
Kawasaki


Someone once told me to marry that motorcycle I was riding ......there's times I wish I hadda listened .

Please Log in or Create an account to join the conversation.

  • notaduc
  • notaduc's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 297
  • Thanks: 3

Re: KZ bore&hone

20 Feb 2012 10:39
#505208
Boring is not the issue, any goofball can operate a boring mill, it is the honing is the tricky part that really determines how straight and round the cylinders are, this takes either a hone that does this automatically ( the Rottler claims straight and round within two tens) or someone with years of experience with the process.

As far as not having a local shop do it, I work at a local shop, our head machinist has been doing this for over 45 years, diesels, race engines, stock build, doesnt matter he keeps the same tolerances.

Problem is that our hone is something like .020 too big (IIRC) for my KZ bore size, and to buy the smaller hone is big bucks, so I sent mine to Joe at Pitstop.
1980 (mostly) KZ1000

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum