Possible valve float
- faffi
-
- Offline
- User
-

Registered
- Posts: 554
- Thanks: 36
Re: Possible valve float
30 Jun 2012 18:20
The plate is set to maximum advance, which should make it hard to start but run OK-ish at higher rpm normally. Whether the timing is correct or not can only be determined by a strobe light.
1977 KZ650B1
1980 F1 engine
B1 3-phase alternator
B1 Points ignition
1980 F1 engine
B1 3-phase alternator
B1 Points ignition
Please Log in or Create an account to join the conversation.
- Surfdude_007
-
Topic Author
- Offline
- User
-

Registered
- Posts: 40
- Thanks: 0
Re: Possible valve float
30 Jun 2012 18:23
Yeah, that was the next step.
1980 KZ1000 B4 LTD
1982 KZ1000 LTD
1982 KZ1000 LTD
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Possible valve float
30 Jun 2012 20:40
That picture actually shows the Ignition plate rotated With the direction or crankshaft travel, this is to Retard the timing. It maybe that it is adjusted as far as the slots would go, and still be to far advanced. Use a timing light to find out where the timing is set. Do you have a manual for the bike/ bikes?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- LarryC
-
- Offline
- User
-

Registered
- Posts: 1241
- Thanks: 309
Re: Possible valve float
30 Jun 2012 20:43
If the airbox is still on the bike, pull the top off, pull the filter out, put the lid back on and see what it does.
Larry C.
Please Log in or Create an account to join the conversation.
- Surfdude_007
-
Topic Author
- Offline
- User
-

Registered
- Posts: 40
- Thanks: 0
Re: Possible valve float
30 Jun 2012 22:58
Yes, I have the manual for the bike. I will try all suggestions tomorrow. Thank you all.
1980 KZ1000 B4 LTD
1982 KZ1000 LTD
1982 KZ1000 LTD
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Possible valve float
30 Jun 2012 23:13 - 30 Jun 2012 23:17
When timing, be sure to align the F
mark with the case mark -- NOT the T
mark.
Ignore the T mark when setting the ignition timing.
For illustration:
Good Fortune!
Ignore the T mark when setting the ignition timing.
For illustration:
Attachment advancerstyles.jpg not found
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 30 Jun 2012 23:17 by Patton.
The following user(s) said Thank You: Surfdude_007
Please Log in or Create an account to join the conversation.
- faffi
-
- Offline
- User
-

Registered
- Posts: 554
- Thanks: 36
Re: Possible valve float
01 Jul 2012 05:37Motor Head wrote: That picture actually shows the Ignition plate rotated With the direction or crankshaft travel, this is to Retard the timing. It maybe that it is adjusted as far as the slots would go, and still be to far advanced. Use a timing light to find out where the timing is set. Do you have a manual for the bike/ bikes?
My bad :blush: - of course it is! If timing should be set closer to full advance, the severely retarded timing will rob the engine of power at revs above 4000 rpm quite substantially.
1977 KZ650B1
1980 F1 engine
B1 3-phase alternator
B1 Points ignition
1980 F1 engine
B1 3-phase alternator
B1 Points ignition
Please Log in or Create an account to join the conversation.
- Surfdude_007
-
Topic Author
- Offline
- User
-

Registered
- Posts: 40
- Thanks: 0
Re: Possible valve float
23 Jul 2012 16:31
Seems like the timing marks(T and F) are to the right of the case mark. and the ignition is moved all the way clockwise. Any suggestions? I might have seen something similar on another thread but couldn't find it. Thanks.
1980 KZ1000 B4 LTD
1982 KZ1000 LTD
1982 KZ1000 LTD
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
