Engine over heating

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Engine over heating

30 Jun 2012 23:48
#532918
Sorry internet dropped out from storm.
You say it only runs 2 minutes then tries to shut off? Again, are you running a fan to move air over the motor when sitting still? The smoke off of the external, that should burn off in a few minutes, that should be left over from working on it, unless you have a leak somewhere. Look at your spark plugs, are they white still or getting colored, especially in the cylinder that got holed. Maybe see if you have some vacuum leaks, around the carb manifolds, or the vacuum hoses. I'd be pulling the carbs and going through them, something had to lean out, probably to hole the piston. What set up are you running? Stock?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
The following user(s) said Thank You: wireman

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: Engine over heating

30 Jun 2012 23:50
#532919
Run a fan to blow air on the motor while its sitting like that.
what are the other symptoms ,where is it idling? B)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • green
  • green's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 18
  • Thanks: 0

Re: Engine over heating

01 Jul 2012 08:34
#532996
Hey Patton, set the valve timing with the cam at the F mark? not the T mark?

Please Log in or Create an account to join the conversation.

  • green
  • green's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 18
  • Thanks: 0

Re: Engine over heating

01 Jul 2012 08:45
#532999
O.K. this is how it is set up, crank mark is on the T both cams are facing inside it starts right up when it is cold, and then shut down after 2 min. when it gets hot, I dont see if I put a fan on it if that would help if I was riding it and had to stop it would still shut down, I can`t even ride it, the bike gets hot and shuts down that quick. Spark plugs are right and gaped at .07-.08

Please Log in or Create an account to join the conversation.

  • green
  • green's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 18
  • Thanks: 0

Re: Engine over heating

01 Jul 2012 09:00
#533001

Attachment 002.JPG not found



Attachment 003.JPG not found



Attachment 001_2012-07-01.JPG not found


Just checked plugs, they look fine!

Please Log in or Create an account to join the conversation.

  • green
  • green's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 18
  • Thanks: 0

Re: Engine over heating

01 Jul 2012 09:02
#533002
all hoses are intact with good seals.

Please Log in or Create an account to join the conversation.

  • green
  • green's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 18
  • Thanks: 0

Re: Engine over heating

01 Jul 2012 09:04
#533004
I have the idle at 1050-1100 put a timing gun on it, it shows F mark.

Please Log in or Create an account to join the conversation.

  • green
  • green's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 18
  • Thanks: 0

Re: Engine over heating

01 Jul 2012 09:10
#533005
I`m about to pull the carbs. I can`t figure this out. Out of mind with this............

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Engine over heating

01 Jul 2012 10:25
#533020
green wrote: Hey Patton, set the valve timing with the cam at the F mark? not the T mark?
Valve timing uses the "T" which is Top Dead Center, the Ignition uses the "F" which is for Fire.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Engine over heating

01 Jul 2012 10:28
#533021
This 2 minute run, is it with the choke on or off?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • green
  • green's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 18
  • Thanks: 0

Re: Engine over heating

01 Jul 2012 11:03
#533032
I`ve looked at the valve timing again, the book says one thing and my bikes gear pattern does not match up with the book. In the book it shows the exhaust Z7ex line straight with a peg, on mine the line splits the link, I made a diagram of the two, were do I start my count to 45th to 46th. or am I being too anal....

Please Log in or Create an account to join the conversation.

  • green
  • green's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 18
  • Thanks: 0

Re: Engine over heating

01 Jul 2012 11:05
#533033
[attachment:1]C:\fakepath\timing_0003.jpg[/attachment]

[attachment:1]C:\fakepath\timing_0003.jpg[/attachment]

[attachment:2]C:\fakepath\timing_0004.jpg[/attachment]
I`ve looked at the valve timing again, the book says one thing and my bikes gear pattern does not match up with the book. In the book it shows the exhaust Z7ex line straight with a peg, on mine the line splits the link, I made a diagram of the two, were do I start my count to 45th to 46th. or am I being too anal....

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum