D PORTING KZ HEAD
- LarryC
-
- Offline
- User
-

Registered
- Posts: 1241
- Thanks: 309
Re: D PORTING KZ HEAD
02 Mar 2013 09:50prostreetkz wrote: I'm truly honored to have you on my discussion, Larry. Now I'm going to get somewhere, lol, That's interesting on the exhaust side, I have read similar info on the exhaust side for porting , really just polishing the exhaust side, maybe a little match porting is sufficient. I want to pick your brain on D porting the intake side. I have read you say it's only needed if the port size is large. First off tapering a port runner, being larger on the carb end and smaller on the valve end will indeed increase velocity is that what the idea is to do? I have a 37.5 intake valve, shouldn't 40mm rs mikunis theoretically work well? Match porting the carb slowly tapering the port to the intended throat size of 89% then blending that to the bowl in turn to the valve seat? I would love to talk to you on the phone , I have also posted this same topic on your forum , again thx larry. I have rs40 mikunis but Have realized I may need 36 or maybe 38s.Cams have 485 at .040, 37.5in 33ex 76mm bore kz 900 crank. I am wanting peak power around 95-10000 but is that to high with heavy stainless valves and steel retainers? about 60% strip 40% street. I think that's all your needing for CSA values Thx Larry
36mm carbs will do the job, 38's really ought to have a J head. 40's are total overkill for the size of the engine IMO
Larry C.
Please Log in or Create an account to join the conversation.
- LarryC
-
- Offline
- User
-

Registered
- Posts: 1241
- Thanks: 309
Re: D PORTING KZ HEAD
22 Apr 2013 07:21 - 22 Apr 2013 07:38Attachment 2013-04-1915.29.51.jpg not found
Here's the result. It's heading home to you today Alan...
38.6 APE GPz11 Intakes turned down to 38.
KW exhausts Springs
Cam Motion Z10 Grind Cams .485 lift [101CFM@that lift@10"] Tested with the intake boots it will run.
APE Guides
OEM 650 Retainers
Valve Job setup for 280-285 shims to avoid the tendency of fracture that is so often seen with thin shims being used in a high performance application.
Normally I would have reduced the velocity a bit more to 270ish. Cams, compression ratio and bore size play into the equation.
Should make plenty of torque
Attachment 2013-04-1915.25.14.jpg not found
Attachment 2013-04-1915.27.28.jpg not found
Attachment 2013-04-2009.46.17.jpg not found
Attachment 2013-04-2011.29.38.jpg not found
Attachment 2013-04-1915.26.40.jpg not found
Larry C.
Last edit: 22 Apr 2013 07:38 by LarryC.
Please Log in or Create an account to join the conversation.
- racer54
-
- Offline
- User
-

Registered
- Posts: 1902
- Thanks: 114
Re: D PORTING KZ HEAD
22 Apr 2013 21:06
It really amazes me how you can get those port walls so even looking without any grinding marks showing. Craftsmanship at its best. Nice job!
1980 LTD (changed over the years), 1979 LTD (being rebuilt), 1977 KZ turbo and various KZ's in various states of build. KLX110
The following user(s) said Thank You: LarryC
Please Log in or Create an account to join the conversation.
- zukdave
-
- Offline
- User
-

Registered
- Posts: 1678
- Thanks: 227
Re: D PORTING KZ HEAD
22 Apr 2013 23:36
Racer that's why I talked to Larry around the first of the
year about doing my GPz750 head.
I just need to finish rounding up part's to send him
with the head.
year about doing my GPz750 head.
I just need to finish rounding up part's to send him
with the head.
1980 KZ650 F1
ZX750A1 motor.
Wiseco 810cc kit.
Zukiworks racing ported head.
VM 29 smooth bore's.
Dyna 2000 Ign. w/Dyna mini coil's
APE cylinder stud's and nut's.
APE valve spring's.
APE Track King clutch.
V/H KZ1000 sidewinder.
3.5x18 laced to a KZ1000 disk hub.
150/60/18 Shinko 006 Podium.
63" wheel base.
ZX750A1 motor.
Wiseco 810cc kit.
Zukiworks racing ported head.
VM 29 smooth bore's.
Dyna 2000 Ign. w/Dyna mini coil's
APE cylinder stud's and nut's.
APE valve spring's.
APE Track King clutch.
V/H KZ1000 sidewinder.
3.5x18 laced to a KZ1000 disk hub.
150/60/18 Shinko 006 Podium.
63" wheel base.
Please Log in or Create an account to join the conversation.
- prostreetkz
-
Topic Author
- Offline
- User
-

Registered
- Posts: 10
- Thanks: 1
Re: D PORTING KZ HEAD
22 Apr 2013 23:42
Yes Larry is the best !!! I can't wait to get the head back !! This bike is going to be an absolute beast!!!!!
THX LARRY
THX LARRY
Please Log in or Create an account to join the conversation.
- Hollywoodmx
-
- Offline
- User
-

Registered
- Posts: 562
- Thanks: 16
Re: D PORTING KZ HEAD
23 Apr 2013 00:13
That is bad ass. What's that all worth?
- 82 GPz1100injection
- 77 Kz1075 Supercharged
- 81 Yamaha TR-1
- 81 Yamaha xv920
Calgary
- 77 Kz1075 Supercharged
- 81 Yamaha TR-1
- 81 Yamaha xv920
Calgary
Please Log in or Create an account to join the conversation.
- LarryC
-
- Offline
- User
-

Registered
- Posts: 1241
- Thanks: 309
Re: D PORTING KZ HEAD
25 Apr 2013 08:12Hollywoodmx wrote: That is bad ass. What's that all worth?
You mean in terms of power?
Larry C.
Please Log in or Create an account to join the conversation.
- Hollywoodmx
-
- Offline
- User
-

Registered
- Posts: 562
- Thanks: 16
Re: D PORTING KZ HEAD
25 Apr 2013 17:52LarryC wrote:Hollywoodmx wrote: That is bad ass. What's that all worth?
You mean in terms of power?
No the cost of parts and work but now that you mentioned it power gains too.
- 82 GPz1100injection
- 77 Kz1075 Supercharged
- 81 Yamaha TR-1
- 81 Yamaha xv920
Calgary
- 77 Kz1075 Supercharged
- 81 Yamaha TR-1
- 81 Yamaha xv920
Calgary
Please Log in or Create an account to join the conversation.
- LarryC
-
- Offline
- User
-

Registered
- Posts: 1241
- Thanks: 309
Re: D PORTING KZ HEAD
25 Apr 2013 18:50prostreetkz wrote: Yes Larry is the best !!! I can't wait to get the head back !! This bike is going to be an absolute beast!!!!!
THX LARRY
You're welcome
Larry C.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
