What does this mean!?!?
- donthaveakawman
-
- User
-

Public
- Thanks: 0
Please Log in or Create an account to join the conversation.
- treitz
-
Topic Author
- Offline
- User
-

Registered
- Posts: 206
- Thanks: 2
Re: What does this mean!?!?
02 Apr 2013 21:43
I thought the air screw only altered the fuel air mixture at idle?
1979 KZ400 - 2-1 Manifold - Mikuni VM34
Please Log in or Create an account to join the conversation.
- treitz
-
Topic Author
- Offline
- User
-

Registered
- Posts: 206
- Thanks: 2
Re: What does this mean!?!?
02 Apr 2013 23:45
After further testing, I think my carb might be malfunctioning. I think my float bowl is actually pushing my floats up, closing off fuel flow.
I can set the float to 0mm or level and it flows fine. Causing the bike to run rich. But if I adjust it at all, fuel will only flow without the bowl snugly tightened. Once I tighten the screws, fuel flow completely stops.
I can set the float to 0mm or level and it flows fine. Causing the bike to run rich. But if I adjust it at all, fuel will only flow without the bowl snugly tightened. Once I tighten the screws, fuel flow completely stops.
1979 KZ400 - 2-1 Manifold - Mikuni VM34
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: What does this mean!?!?
03 Apr 2013 00:03
Too rich pilot mixture may be caused by improperly adjusted air screw which results in sooty spark plugs.
The air screw affects mixture throughout pilot circuit range, not just at idle rpm.
And just for grins, would assure the float mechanism isn't installed upside down.
Good Fortune!
The air screw affects mixture throughout pilot circuit range, not just at idle rpm.
And just for grins, would assure the float mechanism isn't installed upside down.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- Nebr_Rex
-
- Offline
- User
-

Registered
- Posts: 1889
- Thanks: 295
Re: What does this mean!?!?
03 Apr 2013 00:38treitz wrote: After further testing, I think my carb might be malfunctioning. I think my float bowl is actually pushing my floats up, closing off fuel flow.
I can set the float to 0mm or level and it flows fine. Causing the bike to run rich. But if I adjust it at all, fuel will only flow without the bowl snugly tightened. Once I tighten the screws, fuel flow completely stops.
Have you checked your bowl vent?
2002 ZRX1200R
81 GPz1100
79 KZ1000st daily ride
79 KZ1000mk2 prodject
78 KZ650sr
78 KZ650b
81 KZ750e
80 KZ750ltd
77 KZ400/440 cafe project
76 KZ400/440 Fuel Injected
www.dotheton.com/index.php?threads/dr-je...air-of-kz400s.39120/
.
81 GPz1100
79 KZ1000st daily ride
79 KZ1000mk2 prodject
78 KZ650sr
78 KZ650b
81 KZ750e
80 KZ750ltd
77 KZ400/440 cafe project
76 KZ400/440 Fuel Injected
www.dotheton.com/index.php?threads/dr-je...air-of-kz400s.39120/
.
Please Log in or Create an account to join the conversation.
- steell
-
- Offline
- User
-

Registered
- Posts: 6849
- Thanks: 208
Re: What does this mean!?!?
03 Apr 2013 00:59treitz wrote: After further testing, I think my carb might be malfunctioning. I think my float bowl is actually pushing my floats up, closing off fuel flow.
I can set the float to 0mm or level and it flows fine. Causing the bike to run rich. But if I adjust it at all, fuel will only flow without the bowl snugly tightened. Once I tighten the screws, fuel flow completely stops.
Is the float upside down in the float bowl? You can do that when reassembling some carbs.
KD9JUR
Please Log in or Create an account to join the conversation.
- treitz
-
Topic Author
- Offline
- User
-

Registered
- Posts: 206
- Thanks: 2
Re: What does this mean!?!?
03 Apr 2013 11:52
I'm going to have to check when I get home. There is a good chance the float is actually in upside down. However I won't take credit for doing it because I bought the carb used, and have not flipped them while I have had it. I know that for sure.
1979 KZ400 - 2-1 Manifold - Mikuni VM34
Please Log in or Create an account to join the conversation.
- donthaveakawman
-
- User
-

Public
- Thanks: 0
Re: What does this mean!?!?
03 Apr 2013 22:33
big carb/little exhaust equals foul plugs=rich
little carb/big exhaust equals foul plugs=lean
little carb/big exhaust equals foul plugs=lean
Please Log in or Create an account to join the conversation.
- treitz
-
Topic Author
- Offline
- User
-

Registered
- Posts: 206
- Thanks: 2
Re: What does this mean!?!?
04 Apr 2013 00:41donthaveakawman wrote: big carb/little exhaust equals foul plugs=rich
little carb/big exhaust equals foul plugs=lean
You might be right. I may need a more open exhaust.
Turns out my float actually was not upside down. I am having a hard time finding that 3mm sweet spot. But I did get adjusted leaner. So I'll run it tomorrow to see if its too lean. If it is, then I at least know that my float height is the culprit here.
1979 KZ400 - 2-1 Manifold - Mikuni VM34
Please Log in or Create an account to join the conversation.
- treitz
-
Topic Author
- Offline
- User
-

Registered
- Posts: 206
- Thanks: 2
Re: What does this mean!?!?
04 Apr 2013 17:39
Still rich. Still not confident my float height is set correctly, or that my float is operating correctly.
1979 KZ400 - 2-1 Manifold - Mikuni VM34
Please Log in or Create an account to join the conversation.
- steell
-
- Offline
- User
-

Registered
- Posts: 6849
- Thanks: 208
Re: What does this mean!?!?
04 Apr 2013 21:38
If you make a bunch of changes in the carb and it has no effect on the plugs, maybe it's not a carb problem?
Are you getting a healthy blue spark? And are they the right heat range plugs?
And is the timing correct? And? And? And?
Must be the meds :laugh: :laugh:
Are you getting a healthy blue spark? And are they the right heat range plugs?
And is the timing correct? And? And? And?
Must be the meds :laugh: :laugh:
KD9JUR
Please Log in or Create an account to join the conversation.
- treitz
-
Topic Author
- Offline
- User
-

Registered
- Posts: 206
- Thanks: 2
Re: What does this mean!?!?
05 Apr 2013 11:05steell wrote: If you make a bunch of changes in the carb and it has no effect on the plugs, maybe it's not a carb problem?
Are you getting a healthy blue spark? And are they the right heat range plugs?
And is the timing correct? And? And? And?
Must be the meds :laugh: :laugh:
I did check the timing last weekend, and the spark looked strong. I can double check though.
I'm almost positive the carb just isn't working right. It's almost like the floats are hitting something so they wont move freely or something. I think I'm going to just take it to a shop and have them bench test it.
1979 KZ400 - 2-1 Manifold - Mikuni VM34
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
