DYNA S ignition ****help***
- homert1
-
Topic Author
- Offline
- User
-

Registered
- Posts: 55
- Thanks: 6
Re: DYNA S ignition ****help***
16 Aug 2013 14:23
OMR....maybe a stupid question but is there separate fuses for 1-4 and 2-3 cyls?? I had a main fuse issue a while back and found coil short onto the frame was the culprit. I insulated the coils from the frame as indicated by other posts but if separate fuses!!!!!!??? Just maybe???
Please Log in or Create an account to join the conversation.
- Old Man Rock
-
- Offline
- User
-

Registered
- Posts: 6071
- Thanks: 225
Re: DYNA S ignition ****help***
16 Aug 2013 21:03 - 16 Aug 2013 21:08
30 year old KZ, multiple owners sure I guess anything is possible....
Maybe this will help in addition to what others provided....
Dyna S installation & Static Test...
Just in case...
Dyna S coil installation
Sparkies should be non resistive, i.e. B8ES !... Confirm...
What coils installed...? Dyna 3 Ohm...? Verify Primary & Secondary Resistance Measurements... See Below!
* Verify frame/engine/ignition plate is ideally grounded. Continuity (Resistance) measurement from Battery (-) to frame to ignition plate connected to engine.
* Insure battery Voltage >= 12- 13Vdc @ coils (Both) primary terminal.
* Verify spark plug wires and caps are operating to speck... Swap them to other coil for testing if you have no other means to test.
* Insure rotor magnet orientation is correct to spec.
* Insure all connections (power and ignition pickup connections) are to spec!
* Perform static test as described in the write up...
* If all good, then perform Dynamic adjustments.
If still crap, post your findings and get back to us with the results/observations.
Maybe this will help in addition to what others provided....
Dyna S installation & Static Test...
Just in case...
Dyna S coil installation
Sparkies should be non resistive, i.e. B8ES !... Confirm...
What coils installed...? Dyna 3 Ohm...? Verify Primary & Secondary Resistance Measurements... See Below!
* Verify frame/engine/ignition plate is ideally grounded. Continuity (Resistance) measurement from Battery (-) to frame to ignition plate connected to engine.
* Insure battery Voltage >= 12- 13Vdc @ coils (Both) primary terminal.
* Verify spark plug wires and caps are operating to speck... Swap them to other coil for testing if you have no other means to test.
* Insure rotor magnet orientation is correct to spec.
* Insure all connections (power and ignition pickup connections) are to spec!
* Perform static test as described in the write up...
* If all good, then perform Dynamic adjustments.
If still crap, post your findings and get back to us with the results/observations.
Attachment DynaSBenchTest.JPG not found
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
Last edit: 16 Aug 2013 21:08 by Old Man Rock.
Please Log in or Create an account to join the conversation.
- saxjonz
-
- Offline
- User
-

Registered
- KawboyZ
- Posts: 2113
- Thanks: 76
Re: DYNA S ignition ****help***
17 Aug 2013 04:15 - 17 Aug 2013 04:17
Man, the wiring on these bikes can be so messed up with many hands touching over the years. You probably have a wire shorting somewhere. These ignitions are almost bullet proof. A short is almost always the culprit from some wire loose and rubbing against some part and eventually wearing out. Also, the fuse boxes are not the best after this many years. This wouldn't have anything to do with the coils though, if just one coil was working well. They aren't cracked at all? The wires in them are good? You know that I had some issues with the taylor wires I installed and had to get new ones after changing out spark plugs. Have to be really careful with those wires. Make sure you pushed them in nice and deep and that they made contact. You may have a weak ground, you may have a bare wire, if it ran fine, then stopped working anything is possible. Clean all the terminals. Make sure the grounds are clean and not making poor contact, and follow that wiring diagram to the T. I'm sorry but I know I had a frustrating time with mine installing too. But once I got it to work, I never had an issue after. Turns out the wires weren't labeled the way they should have been. Although as you say it was running nicely before so... Sorry for your frustration. Just be patient and follow that flow chart and it will come out just fine.
homert1 wrote: OMR....maybe a stupid question but is there separate fuses for 1-4 and 2-3 cyls?? I had a main fuse issue a while back and found coil short onto the frame was the culprit. I insulated the coils from the frame as indicated by other posts but if separate fuses!!!!!!??? Just maybe???
79 LTD B3
80 LTD B4 1075 kit JE Pistons .410 cam grind, Bassani, 31 keihin CR Specials...
1980 Z1R, 2002 ZRX1200, 2003 ZRX1200
80 LTD B4 1075 kit JE Pistons .410 cam grind, Bassani, 31 keihin CR Specials...
1980 Z1R, 2002 ZRX1200, 2003 ZRX1200
Last edit: 17 Aug 2013 04:17 by saxjonz.
Please Log in or Create an account to join the conversation.
- homert1
-
Topic Author
- Offline
- User
-

Registered
- Posts: 55
- Thanks: 6
Re: DYNA S ignition ****help***
19 Aug 2013 09:59
Thanks to all at KZR!!!! After many hours of tracing wires, checking installation, much frustration and a few pints........I traced it down to a coil touching the frame mount!!!! Isolated the mount as OMR suggested and presto!!! all 4 cyls with spark. Bike runs again............now carbs need some attention and them more mods!!!
THANKS AGAIN GUYS!!!
THANKS AGAIN GUYS!!!
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
