Cam Cover Clearance??

  • 79MKII
  • 79MKII's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Love Them Kaws!
  • Posts: 2478
  • Thanks: 44

Cam Cover Clearance??

16 Jul 2008 09:36
#226503
How much do I need to remove from a stock valve cover for .425 cams? Just the crosses on the intake side or is there more to do?

How do I check it? I'm guessing by installing the cover and turning it over by hand? Can I hear the contact that way?

This is on the '79MKII project.

Thanks
The Kaw List:
Current: 79 KZ1000 A3 MKII, 78 KZ1000 A2, 78 KZ1000 Z1-R, 78 KZ650 SR, 80 KE175
Former: 03 KLX400SR, 99 ZRX1000, 82 KZ750 LTD, 80 KZ1000 A4 MKII, 80 KZ1000 LTD, 78 KZ1000 A2, 74 H-2 750 Triple, 78 KL250

Please Log in or Create an account to join the conversation.

  • FastKaw1
  • FastKaw1's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 141
  • Thanks: 0

Re: Cam Cover Clearance??

16 Jul 2008 09:52
#226509
That the way I do it.
I think you will have to remove just a little more then the crosses
if I remember correctly.
Your doing it right. I don't think there is a wrong way to do it.

Please Log in or Create an account to join the conversation.

  • StreetfighterKz
  • StreetfighterKz's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1672
  • Thanks: 250

Re: Cam Cover Clearance??

16 Jul 2008 10:42
#226515
I saw on another forum that if you need just a tad more clearence after you removed the "X"s use two gaskets.

Later, Doug
1978 z1000 Streetfighter
1976 z900 ‘Stripfighter
1978 z1000 w/RC Turbo
1979 z650 Resto-Mod
1983 Gpz750 Resto-Mod
2018 Z900RS

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: Cam Cover Clearance??

19 Jul 2008 12:33
#227100
Doug is correct. i hope u clearaned the head first though.if not the cams will not turn over.is this a stock motor and head?
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • 79MKII
  • 79MKII's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Love Them Kaws!
  • Posts: 2478
  • Thanks: 44

Re: Cam Cover Clearance??

19 Jul 2008 16:04
#227132
mark1122 wrote:
Doug is correct. i hope u clearaned the head first though.if not the cams will not turn over.is this a stock motor and head?

Definitely not stock - 1260 kit with ported head, o/s valves, mild porting, etc, etc, etc... Head was clearanced for cams as was old cam cover. I'm switching cam covers to a freshly chromed one and want to make sure I have enough clearance for the .425's.

Is the exhaust side OK as is? My old one has some material ground off from intake and exhaust but is that necessary? I had .435 cams in it at one time with a single gasket and never had any problems. I've heard from some that you only need to remove the crosses and you're OK - just looking for some confirmation on that.
Don't want to beat up my new cams!!:blink:
The Kaw List:
Current: 79 KZ1000 A3 MKII, 78 KZ1000 A2, 78 KZ1000 Z1-R, 78 KZ650 SR, 80 KE175
Former: 03 KLX400SR, 99 ZRX1000, 82 KZ750 LTD, 80 KZ1000 A4 MKII, 80 KZ1000 LTD, 78 KZ1000 A2, 74 H-2 750 Triple, 78 KL250

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: Cam Cover Clearance??

19 Jul 2008 18:45
#227158
Just remove the crosses on int and xht is a good start but never leave anything to chance. after the x's are ground off, put the lobes up and put a peice of putty on top. tighten down the cover , then temove the cover and measure the thickness of the putty . now u know where u stand . No guessing.
Your motor sounds like mine, but i just went from 1135cc to 1327 cc's.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • 79MKII
  • 79MKII's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Love Them Kaws!
  • Posts: 2478
  • Thanks: 44

Re: Cam Cover Clearance??

08 Aug 2008 17:50
#230918
I finally tried out the new cover and had enough clearance. I ground off all of the "crosses" and just cleaned up the exhaust side to be safe. I only used one gasket (as I always had in the past) and it was around 1mm thick. Kicked it over first and listened for noise, then started it, then rode it.

Here's a picture before chrome plating:
The Kaw List:
Current: 79 KZ1000 A3 MKII, 78 KZ1000 A2, 78 KZ1000 Z1-R, 78 KZ650 SR, 80 KE175
Former: 03 KLX400SR, 99 ZRX1000, 82 KZ750 LTD, 80 KZ1000 A4 MKII, 80 KZ1000 LTD, 78 KZ1000 A2, 74 H-2 750 Triple, 78 KL250

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum