Exhaust Popping
- KYKZ1100
-
Topic Author
- Offline
- User
-

Registered
- Posts: 106
- Thanks: 2
Exhaust Popping
19 Jul 2008 14:55
I've read a number of threads on this subject but can't get rid of the exhaust popping on my 81 KZ1100A1, both on deceleration and some at constant throttle. The valves are new, the air suction system is gone and I've sealed off the holes in each side of the valve cover, exhaust gaskets are new (fiber-filled copper ones from Z1). Air cleaner is stock paper filter although I've tried a foam filter with no effect. I have 19" aftermarket mufflers that I've put various baffles in with no effect. Carbs have recently been cleaned and rebuilt, and I went up two sizes in jets (120 to 125 mains and 37 to 40 pilots) on the theory that it was running lean with the short mufflers. The plugs look better now - they were white before but now brownish gray, but it didn't affect the popping. I finally tried it last night with the stock mufflers (still with the larger jets) and it still pops, both on deceleration and a little at idle. Carb holders are new and intake boots are all in good shape and not dried out. Vacuum caps and hoses on carbs are new.
The bike runs well - very strong and idles well, no flat spots, and will pull to redline. The only problem I know of is that the compression is low across the board - all four cylinders are between 105 and 115 pounds, and it uses about a quart of oil every 400 miles.
Any ideas about what to look at next to get rid of the popping?
The bike runs well - very strong and idles well, no flat spots, and will pull to redline. The only problem I know of is that the compression is low across the board - all four cylinders are between 105 and 115 pounds, and it uses about a quart of oil every 400 miles.
Any ideas about what to look at next to get rid of the popping?
1981 KZ1100A1 Shaft
2007 BMW R1200R
2007 BMW R1200R
Please Log in or Create an account to join the conversation.
- supercharged
-
- Offline
- User
-

Registered
- Posts: 390
- Thanks: 7
Re: Exhaust Popping
19 Jul 2008 15:15
white lugs are not good - too lean.
Beige/brown plugs are ideal.
Dark / black is too rich.
Beige/brown plugs are ideal.
Dark / black is too rich.
Mike D
- 79 KZ1000 LTD Supercharged
- 80 KZ1000 1105cc Pridmore/Vetter tribute
- 79 Honda CBX
- 03 Z1000 Mod
- 80 KZ1000 LTD Modified
- 80 KZ1000 LTD PROJECT on Hold
- 78 KZ1000/900 - Street big block
- 78 KZ1000-NEEDS HELP!
- 80 CBX -Project STARTED
- 81 GPZ1100
- GSRX1200
- 80 CB750F supersport... eahhh not so good
- 80 CB750F supersport
- 1988 KZ1000 Police - 50K miles
- 1978 KZ1000 LTD - should be a quick project
- 2001 KZ1000 Police - 30K miles - chromed Sgt Bike GREAT SHAPE
- 79 KZ1000 LTD Supercharged
- 80 KZ1000 1105cc Pridmore/Vetter tribute
- 79 Honda CBX
- 03 Z1000 Mod
- 80 KZ1000 LTD Modified
- 80 KZ1000 LTD PROJECT on Hold
- 78 KZ1000/900 - Street big block
- 78 KZ1000-NEEDS HELP!
- 80 CBX -Project STARTED
- 81 GPZ1100
- GSRX1200
- 80 CB750F supersport... eahhh not so good
- 80 CB750F supersport
- 1988 KZ1000 Police - 50K miles
- 1978 KZ1000 LTD - should be a quick project
- 2001 KZ1000 Police - 30K miles - chromed Sgt Bike GREAT SHAPE
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Exhaust Popping
19 Jul 2008 15:35
Could try enriching carb pilot circuit, say 1/4 to 1/2 turn. Good Luck!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Exhaust Popping
19 Jul 2008 15:39
KYKZ1100 wrote:
First, I would check valve clearances.
If those are the true (warm) compression readings with adequate valve clearance, the engine needs work.
The only problem I know of is that the compression is low across the board - all four cylinders are between 105 and 115 pounds, and it uses about a quart of oil every 400 miles.
Any ideas about what to look at next to get rid of the popping?
First, I would check valve clearances.
If those are the true (warm) compression readings with adequate valve clearance, the engine needs work.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- KYKZ1100
-
Topic Author
- Offline
- User
-

Registered
- Posts: 106
- Thanks: 2
Re: Exhaust Popping
19 Jul 2008 16:13
Patton, I'll try that.
Bountyhunter - The valves are new (~1,000 miles on them) and all were within specs after they were replaced, but if I can't figure anything else out, I'll check them again.
I checked the compression several times after the valves were redone, both cold without the carbs installed and warm, and the reading were pretty consistent. The highest I saw was cold and one cylinder was 120, the others between 105 and 112 or so. When I put oil in the cylinders, the pressure went up to 145-150 or so on all cylinders.
I bought three NOS 2nd oversize OEM pistons on eBay a month or so ago. If I can find a fourth I'll use those, otherwise I'll look at Wiseco, and I plan to have it bored and put in new pistons and rings this fall. I don't really need more performance and don't really want higher compression so I'd just soon stick with stock.
Bountyhunter - The valves are new (~1,000 miles on them) and all were within specs after they were replaced, but if I can't figure anything else out, I'll check them again.
I checked the compression several times after the valves were redone, both cold without the carbs installed and warm, and the reading were pretty consistent. The highest I saw was cold and one cylinder was 120, the others between 105 and 112 or so. When I put oil in the cylinders, the pressure went up to 145-150 or so on all cylinders.
I bought three NOS 2nd oversize OEM pistons on eBay a month or so ago. If I can find a fourth I'll use those, otherwise I'll look at Wiseco, and I plan to have it bored and put in new pistons and rings this fall. I don't really need more performance and don't really want higher compression so I'd just soon stick with stock.
1981 KZ1100A1 Shaft
2007 BMW R1200R
2007 BMW R1200R
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Exhaust Popping
20 Jul 2008 13:18
KYKZ1100 wrote:
So the ring to wall seal isn't holding well.
KYKZ1100 wrote:
Smart move, those bikes make plenty of power stock.
Patton, I'll try that.
Bountyhunter - The valves are new (~1,000 miles on them) and all were within specs after they were replaced, but if I can't figure anything else out, I'll check them again.
I checked the compression several times after the valves were redone, both cold without the carbs installed and warm, and the reading were pretty consistent. The highest I saw was cold and one cylinder was 120, the others between 105 and 112 or so. When I put oil in the cylinders, the pressure went up to 145-150 or so on all cylinders.
So the ring to wall seal isn't holding well.
KYKZ1100 wrote:
I bought three NOS 2nd oversize OEM pistons on eBay a month or so ago. If I can find a fourth I'll use those, otherwise I'll look at Wiseco, and I plan to have it bored and put in new pistons and rings this fall. I don't really need more performance and don't really want higher compression so I'd just soon stick with stock.
Smart move, those bikes make plenty of power stock.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- coppertales
-
- Offline
- User
-

Registered
- Posts: 321
- Thanks: 0
Re: Exhaust Popping
21 Jul 2008 08:35
My 82 A2 did that until I replaced the rings. Nice and quiet now. I just used stock rings from Z1, after inspecting the pistons to make sure they were ok and did a glaze break honing on the cylinders. I could not afford to bore and go oversize pistons at this time. This bike had 39000 miles on it and the engine had never been apart until I did the valves at 37000 miles. One of them was leaking....should have done the rings too but I had hoped the valve job would cure the ills...chris3
1982 KZ1100 A2
1982 1100 SPECTRE
1982 1100 SPECTRE
1982 1100 SPECTRE
1982 1100 SPECTRE
Please Log in or Create an account to join the conversation.
- KYKZ1100
-
Topic Author
- Offline
- User
-

Registered
- Posts: 106
- Thanks: 2
Re: Exhaust Popping
21 Jul 2008 22:43
Thanks chris. I don't understand the mechanism by which poor compression causes backfiring but I know the rings have to be done anyway. I'm going to try Patton's idea of adjusting the pilot circuit (haven't had 2 minutes this week to try it), but if that's not the problem I'll just put up with it until I can have the pistons and rings done this fall.
1981 KZ1100A1 Shaft
2007 BMW R1200R
2007 BMW R1200R
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
