Stubborn helicoil
- kzwolfsr
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1221
- Thanks: 16
Stubborn helicoil
29 Jul 2008 05:51
I have been putting helicoils in my can cap holes since they are all stripped out only under my number one cap on my 1000. I got the rethreading right but the helicoil goes in at the very begining and stops turning. I burned out like 6 of these things just to get them to screw in and I rethread to make sure it is alright but the coils still jam. What could be wrong here. The threading tool came with the coils so I have the right tap. I wanna ride. O by the way. I got to ride the bike a week ago and the ride went down in disaster.
1979 KZ SR650, stock candy persimmon red and crossover pipes
1981 KZ 1000LTD with non stock and more comfortable handle bars and 4 into one V&H
Original man of the Caribbean
1981 KZ 1000LTD with non stock and more comfortable handle bars and 4 into one V&H
Original man of the Caribbean
Please Log in or Create an account to join the conversation.
- Bluemeanie
-
- Offline
- User
-

Registered
- Posts: 2516
- Thanks: 15
Re: Stubborn helicoil
29 Jul 2008 06:03
Are you using the tap that came with the kit? Sure sounds like a thread mismatch to me. I've installed hundreds of helicoils with no problem. Check your tap...
1980 KZ650F1, Bought new out the door for $2,162.98!
Please Log in or Create an account to join the conversation.
- kzwolfsr
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1221
- Thanks: 16
Re: Stubborn helicoil
29 Jul 2008 07:02
yeah its the one that came with the kit
But I have done helicoils before and it was fun untill now. I put the helicoil and the tap side by side to see if the threads will mesh and they are a little off, unless you stretch it or just mash it in alittle. I new this would solve my problem but it was never this hard!
But I have done helicoils before and it was fun untill now. I put the helicoil and the tap side by side to see if the threads will mesh and they are a little off, unless you stretch it or just mash it in alittle. I new this would solve my problem but it was never this hard!
1979 KZ SR650, stock candy persimmon red and crossover pipes
1981 KZ 1000LTD with non stock and more comfortable handle bars and 4 into one V&H
Original man of the Caribbean
1981 KZ 1000LTD with non stock and more comfortable handle bars and 4 into one V&H
Original man of the Caribbean
Please Log in or Create an account to join the conversation.
- harm
-
- Offline
- User
-

Registered
- Tom
- Posts: 681
- Thanks: 13
Re: Stubborn helicoil
29 Jul 2008 09:35
The tap should be an "STI" tap. So if it is a 6mm thread it should read something like "6.0 x 1.0 STI". STI stands for screw thread inserts. You may try running the tap in the hole again to clean it out.
Tom
Holland, MI
1980 KZ550 ELR
2011 Concours14
2017 KX450 [/color]
Holland, MI
1980 KZ550 ELR
2011 Concours14
2017 KX450 [/color]
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Stubborn helicoil
29 Jul 2008 11:33
Could the Heli-coils themselves be incorrect? Manufacturers make mistakes too and maybe it got missed in quality control or shipping?
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: Stubborn helicoil
29 Jul 2008 13:53
What does the installer tool look like? Does yours have a slot in the end or a tab?
i have 2 dif brands and 1 gives me headaches.the best 1 has a slot on the end for the coils tang to fit into. u can make 1 by slotting a drill bit.
i have 2 dif brands and 1 gives me headaches.the best 1 has a slot on the end for the coils tang to fit into. u can make 1 by slotting a drill bit.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: Stubborn helicoil
29 Jul 2008 13:57
When u install your cams use a longer threaded rod on 2 of the cap bolts.thread the rods in then use nuts to pull the cap down. the cap that pulls the lobe that is faceing toward the valve.
It is easy to stip the bolts on those things.
It is easy to stip the bolts on those things.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- kzwolfsr
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1221
- Thanks: 16
Re: Stubborn helicoil
29 Jul 2008 16:55
ok Fellas. I cleaned the threaded hole a bunch of times and nothing, it just sits there and clicks and threatens to break the tang off if I twist it anymore. The original bolts thread into the helicoil just fine, but the helicoil doesnt thread into the threaded hole. I like your idea Mark, but if I did something like that wouldn't I have to get a bolt that is bigger on one side now? Since I did use a bigger tap? I think I will go get a bolt that will fit the holes and see if the tap is wrong. Anymore suggestions?
1979 KZ SR650, stock candy persimmon red and crossover pipes
1981 KZ 1000LTD with non stock and more comfortable handle bars and 4 into one V&H
Original man of the Caribbean
1981 KZ 1000LTD with non stock and more comfortable handle bars and 4 into one V&H
Original man of the Caribbean
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: Stubborn helicoil
29 Jul 2008 19:43
i dont understand what u mean "I like your idea Mark, but if I did something like that wouldn't I have to get a bolt that is bigger on one side now? Since I did use a bigger tap? "
are u saying u tapped the hole to a larger size? my kz 900 uses 6mm. what does yours take and what size did u increase it to?
are u saying u tapped the hole to a larger size? my kz 900 uses 6mm. what does yours take and what size did u increase it to?
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- APE Jay
-
- User
-

Public
- Thanks: 0
Re: Stubborn helicoil
29 Jul 2008 22:24
Sure sounds like you are trying to install 1/4-20 coils in a hole tapped for 6 mm.
Jay
Jay
Please Log in or Create an account to join the conversation.
- kzwolfsr
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1221
- Thanks: 16
Re: Stubborn helicoil
30 Jul 2008 06:08
the bolts are 6mm. i used a helicoil kit from autozone with insert tool, tap and coils included. The kit was for the 6mm bolts and i even tried it on the bolt before I bought it and it screwd on great. As for the tap or the threads created by the tap in the package, the helicoil nevr screws into the hole. Could there be a possibility of the wrong tap if when I put the threads of the coil and tap side by side and the threads dont mesh without really pushing the coil into the tap? Mark for your question I meant shouldn't the bolt now have a bigger side to screw into the now tapped hole while the other side of the bolt have a smaller diameter to fit into the small holes in the cam cap?
1979 KZ SR650, stock candy persimmon red and crossover pipes
1981 KZ 1000LTD with non stock and more comfortable handle bars and 4 into one V&H
Original man of the Caribbean
1981 KZ 1000LTD with non stock and more comfortable handle bars and 4 into one V&H
Original man of the Caribbean
Please Log in or Create an account to join the conversation.
- BSKZ650
-
- Offline
- User
-

Registered
- Posts: 2061
- Thanks: 14
Re: Stubborn helicoil
30 Jul 2008 06:16
I would go down and get a new set, something is wrong, and its really not your job to figure out what it is, get a new set
77 kz650, owned for over 25 years
77 ltd1000, current rider
76 kz900, just waiting
73 z1,, gonna restore this one
piglet, leggero harley davidson
SR, Ride captian, S.E.Texas Patriot Guard Riders.. AKA KawaBob
77 ltd1000, current rider
76 kz900, just waiting
73 z1,, gonna restore this one
piglet, leggero harley davidson
SR, Ride captian, S.E.Texas Patriot Guard Riders.. AKA KawaBob
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
