timeing adjustment?
- BigBlockT
-
Topic Author
- Offline
- User
-

Registered
- Posts: 99
- Thanks: 0
timeing adjustment?
09 Nov 2008 09:17
not to sound like a dummy does it matter which plug wire to use 1 or 4 to hook a timeing light to and what is the timeing to be set at for a 74 z1-900 with a dyna-s and the rest all stock except for the header ?
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: timeing adjustment?
09 Nov 2008 11:14
As you sit on the bike the left coil fires the #1 and #4 sparkplugs at the same time and the right coil fires #2 and #3. Sparkplugs are numbered from left to right sitting on the seat.
This type of ignition is considered a "wasted Spark" as it is fired during an exhaust stroke.
Does this answer your question?
This type of ignition is considered a "wasted Spark" as it is fired during an exhaust stroke.
Does this answer your question?
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- BigBlockT
-
Topic Author
- Offline
- User
-

Registered
- Posts: 99
- Thanks: 0
Re: timeing adjustment?
09 Nov 2008 13:14
you helped with 1/2 of the question now what should the timeing be set at (what degree)?
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: timeing adjustment?
09 Nov 2008 14:22
In January 1994 the advancer changed to 20 degrees BTDC @ 1500 rpm from the previous 5 degrees.
Early advancer. Note close distance between F and T marks.
Early advancer. Note close distance between F and T marks.
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: timeing adjustment?
09 Nov 2008 14:25
Later advancer. Note further distance between F and T marks.
Why not just set timing at idle rpm by aligning the F mark with permanent timing mark on engine case?
Good Luck!
Why not just set timing at idle rpm by aligning the F mark with permanent timing mark on engine case?
Good Luck!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: timeing adjustment?
09 Nov 2008 14:55 - 09 Nov 2008 15:17
Info from Z1E website:
If you have a 73 Z1 or an early 74 Z1A, we may need to supply a different crank rotor. Up through engine number Z1F-32817 kawasaki installed a 5/40 degree mechanical advancer (normal fire mark is 5 degrees then advancing to 40 degrees). If you have one of these on your engine, please enter a note in the special instructions to replace the standard rotor (3 rotor) in the Dyna-S with one special for these early bikes (3A rotor).)
Interpreted to mean that different rotors are needed for using a Dyna-S, depending on which advancer is fitted.
From your post, I am wondering if maybe the wrong Dyna-S rotor is fitted.
Sorry, I don't know how to visually tell the difference between the two separate Dyna-S rotors, or whether a Dyna-S rotor/advancer "misfit" may be finessed by simply re-setting the timing at idle rpm (thinking probably not, as it would also change the higher rpm advance from the desired 40 degrees BTDC.)
But am thinking the later advancer would be a direct swap replacement, as an option for using the "standard" Dyna-S rotor.
Good Luck!
If you have a 73 Z1 or an early 74 Z1A, we may need to supply a different crank rotor. Up through engine number Z1F-32817 kawasaki installed a 5/40 degree mechanical advancer (normal fire mark is 5 degrees then advancing to 40 degrees). If you have one of these on your engine, please enter a note in the special instructions to replace the standard rotor (3 rotor) in the Dyna-S with one special for these early bikes (3A rotor).)
Interpreted to mean that different rotors are needed for using a Dyna-S, depending on which advancer is fitted.
From your post, I am wondering if maybe the wrong Dyna-S rotor is fitted.
Sorry, I don't know how to visually tell the difference between the two separate Dyna-S rotors, or whether a Dyna-S rotor/advancer "misfit" may be finessed by simply re-setting the timing at idle rpm (thinking probably not, as it would also change the higher rpm advance from the desired 40 degrees BTDC.)
But am thinking the later advancer would be a direct swap replacement, as an option for using the "standard" Dyna-S rotor.
Good Luck!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 09 Nov 2008 15:17 by Patton.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
