one last question...(we hope).....
- keith1
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1646
- Thanks: 3
one last question...(we hope).....
05 Dec 2008 16:54
what to fill the area where the rubber o ring resides in a stock motor.....i m using one pc head gasket
and was advised to use silicone....i m guessing i cant use the stuff in the bathroom...what brand? for what original application? would the high temp black rtv stuff be no good......i should be bolting my redone head on in the next couple of weeks and i m getting antsy for the sniff of exaust in the garage......as always thanks in advance....keith:woohoo:
and was advised to use silicone....i m guessing i cant use the stuff in the bathroom...what brand? for what original application? would the high temp black rtv stuff be no good......i should be bolting my redone head on in the next couple of weeks and i m getting antsy for the sniff of exaust in the garage......as always thanks in advance....keith:woohoo:
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: one last question...(we hope).....
06 Dec 2008 15:08
I used the black Permatex. As long as it can take the heat, any silicone should be fine. just get it a smidge higher than the surface so it will seal the oil into the galley .Not too high.Let it dry before u assemble.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- keith1
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1646
- Thanks: 3
Re: one last question...(we hope).....
06 Dec 2008 15:31
mark1122 wrote:
thanks guys.....mark, i think i am going that route as it is high temp....i have some in my tool box....i just feel better about using that
stuff...i dont know why, but i do.....
I used the black Permatex. As long as it can take the heat, any silicone should be fine. just get it a smidge higher than the surface so it will seal the oil into the galley .Not too high.Let it dry before u assemble.
thanks guys.....mark, i think i am going that route as it is high temp....i have some in my tool box....i just feel better about using that
stuff...i dont know why, but i do.....
Please Log in or Create an account to join the conversation.
- pstrbrc
-
- Offline
- User
-

Registered
- '81 GPz 1100 project
- Posts: 355
- Thanks: 9
Re: one last question...(we hope).....
06 Dec 2008 18:02
Oh, come on. Use the red stuff. LOTS of it. Let it squish out and goober down the front of the motor. And leave it there.
Yeah, black hi temp rtv is the stuff.
BTW.....
quiz for the day.
WITHOUT GOOGLING OR OTHERWISE SNEEKING A PEEK AT ANY REFERENCE MATERIAL...
What does "RTV" stand for?
Yeah, black hi temp rtv is the stuff.
BTW.....
quiz for the day.
WITHOUT GOOGLING OR OTHERWISE SNEEKING A PEEK AT ANY REFERENCE MATERIAL...
What does "RTV" stand for?
\'81 GPz 1100 project
Elkhart, Kansas USA
\"Man does not control his own fate. The women in his life do that for him.\" Groucho Marx
Elkhart, Kansas USA
\"Man does not control his own fate. The women in his life do that for him.\" Groucho Marx
Please Log in or Create an account to join the conversation.
- keith1
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1646
- Thanks: 3
Re: one last question...(we hope).....
06 Dec 2008 18:27
pstrbrc wrote:
i m guessing the v is for vulcanization....but as in life i am clueless about the rest....:laugh:
Oh, come on. Use the red stuff. LOTS of it. Let it squish out and goober down the front of the motor. And leave it there.
Yeah, black hi temp rtv is the stuff.
BTW.....
quiz for the day.
WITHOUT GOOGLING OR OTHERWISE SNEEKING A PEEK AT ANY REFERENCE MATERIAL...
What does "RTV" stand for?
i m guessing the v is for vulcanization....but as in life i am clueless about the rest....:laugh:
Please Log in or Create an account to join the conversation.
- keith1
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1646
- Thanks: 3
Re: one last question...(we hope).....
06 Dec 2008 18:30
keith1 wrote:
i just had a brain fart...room temperature vulcanization?........and no i didnt cheat if i got it right...if i didnt, i can continue to cruise through life a clueless retard...shit, i cant lose.....:laugh:
pstrbrc wrote:Oh, come on. Use the red stuff. LOTS of it. Let it squish out and goober down the front of the motor. And leave it there.
Yeah, black hi temp rtv is the stuff.
BTW.....
quiz for the day.
WITHOUT GOOGLING OR OTHERWISE SNEEKING A PEEK AT ANY REFERENCE MATERIAL...
What does "RTV" stand for?
i m guessing the v is for vulcanization....but as in life i am clueless about the rest....:laugh:
i just had a brain fart...room temperature vulcanization?........and no i didnt cheat if i got it right...if i didnt, i can continue to cruise through life a clueless retard...shit, i cant lose.....:laugh:
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: one last question...(we hope).....
06 Dec 2008 18:56
Real Thick Viscosity.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- keith1
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1646
- Thanks: 3
Re: one last question...(we hope).....
06 Dec 2008 19:21
mark1122 wrote:
mark,
tell me thats not the right answer!!!:laugh:
Real Thick Viscosity.
mark,
tell me thats not the right answer!!!:laugh:
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: one last question...(we hope).....
07 Dec 2008 05:58
:lol: :silly: :blink:
I hope not.
I hope not.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- kawsakiman
-
- Offline
- User
-

Registered
- Posts: 1246
- Thanks: 6
Re: one last question...(we hope).....
07 Dec 2008 21:03 - 07 Dec 2008 21:06
keith1 beat me to it.
foiled again!
for once i knew the answer and was a day late and a dollar short.
foiled again!
for once i knew the answer and was a day late and a dollar short.
someday i will be able to afford my kz habit.
Last edit: 07 Dec 2008 21:06 by kawsakiman.
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: one last question...(we hope).....
07 Dec 2008 21:33
RTV = Room Temperature Vulcanizing
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
