Valve shims question
- dman3998
-
Topic Author
- Offline
- User
-

Registered
- Posts: 143
- Thanks: 0
Valve shims question
10 Jan 2009 22:07
I was checking the valve clearance, (1000 B3) they were all almost the same 265 - 275 all had the same wear about .04mm so I need to get a bunch of 260's and 265's.
My question is one of the shims had "270A" on it I have never seen any with letters. any ideas what it means?
Thanks
Dman
My question is one of the shims had "270A" on it I have never seen any with letters. any ideas what it means?
Thanks
Dman
Dman
SE Idaho
"Smart only goes just so far, STUPID is UN-limited"
79 KZ1000 LTD
Honda XRL650L
Yamaha RD350B
Yamaha DT400B
SE Idaho
"Smart only goes just so far, STUPID is UN-limited"
79 KZ1000 LTD
Honda XRL650L
Yamaha RD350B
Yamaha DT400B
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Valve shims question
11 Jan 2009 14:04
dman3998 wrote:
dman3998 wrote:
Are you saying the shims showed .04 mm wear as to thickness compared to the marked thickness? That would be very unusual. Did you measure it with a calibrated set of calipers?I was checking the valve clearance, (1000 B3) they were all almost the same 265 - 275 all had the same wear about .04mm so I need to get a bunch of 260's and 265's.
dman3998 wrote:
I have seen it and I just ignored it. I don't know what it means either. I just measure the thickness and mark them myself since some of mine have the factory marks rubbed off.My question is one of the shims had "270A" on it I have never seen any with letters. any ideas what it means?
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- keith1
-
- Offline
- User
-

Registered
- Posts: 1646
- Thanks: 3
Re: Valve shims question
11 Jan 2009 16:48Please Log in or Create an account to join the conversation.
- timebomb33
-
- Offline
- User
-

Registered
- Posts: 4277
- Thanks: 10
Re: Valve shims question
11 Jan 2009 17:32
thats pretty cool info i've never seen those id markings described or explained before see i knew if i came on here i would learn something new today.
1973 z1 2-1974z1-a,2-1975z1-b dragbikes1015cc+1393cc, 1977kz1000,1978kz1000,1981kz1000j, 1997 zx-11, 2000 z12r,1428turbo nitrous pro-mod and a shit load of parts thats all for now leader sask.,CANADA
I THINK MY POWERBAND BROKE
I THINK MY POWERBAND BROKE
Please Log in or Create an account to join the conversation.
- keith1
-
- Offline
- User
-

Registered
- Posts: 1646
- Thanks: 3
Re: Valve shims question
11 Jan 2009 17:46
timebomb33 wrote:
c'mon man...you have probably forgotten more than most know!!!!!!:laugh:
thats pretty cool info i've never seen those id markings described or explained before see i knew if i came on here i would learn something new today.
c'mon man...you have probably forgotten more than most know!!!!!!:laugh:
Please Log in or Create an account to join the conversation.
- timebomb33
-
- Offline
- User
-

Registered
- Posts: 4277
- Thanks: 10
Re: Valve shims question
11 Jan 2009 18:03
yah probably but it's nice to get a refresher course once in a while.
1973 z1 2-1974z1-a,2-1975z1-b dragbikes1015cc+1393cc, 1977kz1000,1978kz1000,1981kz1000j, 1997 zx-11, 2000 z12r,1428turbo nitrous pro-mod and a shit load of parts thats all for now leader sask.,CANADA
I THINK MY POWERBAND BROKE
I THINK MY POWERBAND BROKE
Please Log in or Create an account to join the conversation.
- dman3998
-
Topic Author
- Offline
- User
-

Registered
- Posts: 143
- Thanks: 0
Re: Valve shims question
11 Jan 2009 19:55
that is good info. thanks
Dman
SE Idaho
"Smart only goes just so far, STUPID is UN-limited"
79 KZ1000 LTD
Honda XRL650L
Yamaha RD350B
Yamaha DT400B
SE Idaho
"Smart only goes just so far, STUPID is UN-limited"
79 KZ1000 LTD
Honda XRL650L
Yamaha RD350B
Yamaha DT400B
Please Log in or Create an account to join the conversation.
- luc
-
- Offline
- User
-

Registered
- Posts: 78
- Thanks: 1
Re: Valve shims question
15 Jan 2009 20:28
Redlinecycle is wrong regarding the explanation for the "A" on a shim.
It is not, as they said, to denote a slightly thicker shim installed at the factory but rather is is to identify shims that had a stricter QC standards.
Back in June 21 1973, Kawasaki issued a Service Bulletin (73 Z-13) titled "Z1 tapped replacement" to addres the issue of shims faillure due to a combination of shim and tappet design..
The tappet had an oil hole/navel in the center and the shims were flexing on top of it and fracturing.
To solve the problem tappets were replaced with tappets without oil hole/navel and new shims were put in production with a much stricter QC and all bikes in service were supposed to have both tappets and shims replaced regardless of their warranty status.
Kawasaki called that a "factory directed modification" and allowed 1.5 hour for the job
Those shims were identified with the letter "A" but did not have a new or differernt part #.
After a few years,assuming that all the earlier, non "A" shims woud have been removed from service and inventory, Kawasaki dropped the "A".
It is not, as they said, to denote a slightly thicker shim installed at the factory but rather is is to identify shims that had a stricter QC standards.
Back in June 21 1973, Kawasaki issued a Service Bulletin (73 Z-13) titled "Z1 tapped replacement" to addres the issue of shims faillure due to a combination of shim and tappet design..
The tappet had an oil hole/navel in the center and the shims were flexing on top of it and fracturing.
To solve the problem tappets were replaced with tappets without oil hole/navel and new shims were put in production with a much stricter QC and all bikes in service were supposed to have both tappets and shims replaced regardless of their warranty status.
Kawasaki called that a "factory directed modification" and allowed 1.5 hour for the job
Those shims were identified with the letter "A" but did not have a new or differernt part #.
After a few years,assuming that all the earlier, non "A" shims woud have been removed from service and inventory, Kawasaki dropped the "A".
Please Log in or Create an account to join the conversation.
- dman3998
-
Topic Author
- Offline
- User
-

Registered
- Posts: 143
- Thanks: 0
Re: Valve shims question
17 Jan 2009 09:18
I wonder if we could figure out a way to trade shims?
After re-shimming my motor I have a bunch of extra 270 and 260 shims that I probably will never use. and I still need a 275.
There are enough guys in every country that we would never have to actually buy a new shim. and for less than a buck you could post a couple of shims anywhere in the country.
I'm not sure how it would work but its a concept anyway.
dman
After re-shimming my motor I have a bunch of extra 270 and 260 shims that I probably will never use. and I still need a 275.
There are enough guys in every country that we would never have to actually buy a new shim. and for less than a buck you could post a couple of shims anywhere in the country.
I'm not sure how it would work but its a concept anyway.
dman
Dman
SE Idaho
"Smart only goes just so far, STUPID is UN-limited"
79 KZ1000 LTD
Honda XRL650L
Yamaha RD350B
Yamaha DT400B
SE Idaho
"Smart only goes just so far, STUPID is UN-limited"
79 KZ1000 LTD
Honda XRL650L
Yamaha RD350B
Yamaha DT400B
Please Log in or Create an account to join the conversation.
- keith1
-
- Offline
- User
-

Registered
- Posts: 1646
- Thanks: 3
Re: Valve shims question
17 Jan 2009 09:22
dman3998 wrote:
thats a good idea...kind of like a shim exchange program....maybe site owner would be willing to set something up....might not be on the top ten list with vendors, but i think the membership might like it.....
I wonder if we could figure out a way to trade shims?
After re-shimming my motor I have a bunch of extra 270 and 260 shims that I probably will never use. and I still need a 275.
There are enough guys in every country that we would never have to actually buy a new shim. and for less than a buck you could post a couple of shims anywhere in the country.
I'm not sure how it would work but its a concept anyway.
dman
thats a good idea...kind of like a shim exchange program....maybe site owner would be willing to set something up....might not be on the top ten list with vendors, but i think the membership might like it.....
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Valve shims question
17 Jan 2009 13:59
Problem is, sending a small package these days is like $8 which is about what a couple of shims cost.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- keith1
-
- Offline
- User
-

Registered
- Posts: 1646
- Thanks: 3
Re: Valve shims question
17 Jan 2009 14:13
bountyhunter wrote:
true
Problem is, sending a small package these days is like $8 which is about what a couple of shims cost.
true
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
