1977 KZ1000 A1
- gane
-
Topic Author
- Offline
- User
-

Registered
- Posts: 706
- Thanks: 1
1977 KZ1000 A1
11 Jan 2009 23:58
All, Academic question... I bought This bike under a "distressed sale" Sorry, no pic's. No tank, sidecovers,seat.or exhaust. and crank only rotated @ 30 degrees for @ aft. still, for $100.00 w/title I bit. Speedo indicated 50K miles. Teardown revealed bent valves,worn out cam chain and missing bits. w/cyls/pistons within spec (just)and bottom end clogged w/barely viscous goo. still, trans was good, cl basket fair and oil pump/crank same. So... new valves, fresh seats, rings and hone, cam chain, chicklets tensionor rubber bits, gaskets/seals, and blah blah. compression 120-140 across board, leakdown 2-4%. mostly rings. ign. stock (points) w/29 smoothbores,oval K&N's, and Kerker street exhaust. a summer of riding was pleasant, tho seemed soft.so, prior to launching into jetting/ign. put it on the dyno. Lo, corrected hp is only 72 hp. even w/ sloppy bore, I'd have thought 80, Am I being un realistic? I'm at 5k ft, and temp was @ 40dgrees, EGA #'s @ 3.% idle and @1.50 cruise w@350ppm H/C @ 5k rpm. Thoughts... G
[img][/img] 1977 KZ1000A1
Please Log in or Create an account to join the conversation.
- PLUMMEN
-
- Offline
- User
-

Registered
- Posts: 7983
- Thanks: 104
Re: 1977 KZ1000 A1
12 Jan 2009 05:31
compression is a little off between cylinders ,valves adjusted?other than the numbers being off between cylinders a little that sounds fairly realistic for a basically stock motor with stock head/cams and a loose bore to me anyway.
Still recovering,some days are better than others.
Please Log in or Create an account to join the conversation.
- timebomb33
-
- Offline
- User
-

Registered
- Posts: 4277
- Thanks: 10
Re: 1977 KZ1000 A1
12 Jan 2009 09:34
at that altitude 72 horse for a stock motor is not bad you lose 3% for every thousand feet of elevation so at sea level your motor would make about 84 horse power. so i don't think your to far off.
1973 z1 2-1974z1-a,2-1975z1-b dragbikes1015cc+1393cc, 1977kz1000,1978kz1000,1981kz1000j, 1997 zx-11, 2000 z12r,1428turbo nitrous pro-mod and a shit load of parts thats all for now leader sask.,CANADA
I THINK MY POWERBAND BROKE
I THINK MY POWERBAND BROKE
Please Log in or Create an account to join the conversation.
- gane
-
Topic Author
- Offline
- User
-

Registered
- Posts: 706
- Thanks: 1
Re: 1977 KZ1000 A1
13 Jan 2009 18:19
P & T, thanks for 'back... Dyno #'s are corrected for alt, so I guess I'm missing @ 10 hp. I'll continue to fiddle, perhaps a comp baffle and drop needles. Thks g
[img][/img] 1977 KZ1000A1
Please Log in or Create an account to join the conversation.
- arai59
-
- User
-

Public
- Thanks: 0
Please Log in or Create an account to join the conversation.
- wiredgeorge
-
- Offline
- User
-

Registered
- Posts: 5298
- Thanks: 46
Re: 1977 KZ1000 A1
14 Jan 2009 07:05
72 HP is pretty good actually. You will normally see mid to high 60s on most 900cc models.
wiredgeorge Motorcycle Carburetors
Mico TX
www.wgcarbs.com
Too many bikes to list!
Mico TX
www.wgcarbs.com
Too many bikes to list!
Please Log in or Create an account to join the conversation.
- EricHa
-
- Offline
- User
-

Registered
- Posts: 138
- Thanks: 1
Re: 1977 KZ1000 A1
14 Jan 2009 08:09
Published horsepower numbers were always bhp measured at the crankshaft. Rear wheel horsepower numbers will always be lower.
"Brake horsepower (BHP) is the amount of work generated by a motor without taking into consideration any of the various auxiliary components that may slow down the actual speed of the motor. Sometimes referred to as pure horsepower."
"Brake horsepower (BHP) is the amount of work generated by a motor without taking into consideration any of the various auxiliary components that may slow down the actual speed of the motor. Sometimes referred to as pure horsepower."
1977 Kawasaki KZ900A5
1975 Honda CB550K
1996 Ducati 900SS CR
1975 Honda CB550K
1996 Ducati 900SS CR
Please Log in or Create an account to join the conversation.
- kawtoy
-
- Offline
- User
-

Registered
- Posts: 806
- Thanks: 6
Re: 1977 KZ1000 A1
14 Jan 2009 08:56
After I dug my 80 1000 out of storage where it had sat for 15 years I had it dynoed. Stock engine with 4-1 Kerker and jets. It made 75hp in TN which was pretty close to sea level. Bike was blowing a good amount of black smoke so I am sure the rings were shot even though it only had 3,000 miles on it. Sitting that long is never good for an engine. I would say 72hp is just about right for your mods and elevation. You might be able to squeeze another 5hp out of it with a carb sync, coil mod, playing with jetting to find right match for your altitude, and mamybe some adjustable cam gears so you can dial the cams in dead on.
Harley Davidson- Turning gas into noise without the harmful affects of horsepower for over 100 years.
Please Log in or Create an account to join the conversation.
- gane
-
Topic Author
- Offline
- User
-

Registered
- Posts: 706
- Thanks: 1
Re: 1977 KZ1000 A1
14 Jan 2009 16:58
Again, thanks for feedback. Trying to build a competitive Hot-rod wasn't my intent. My labors were simply to reproduce a bike I coveted and still regard as one of the prettiest made. The periodic nod's I get from current sportbike riders as they slow in mid-pass is nearly as rewarding as the feeling of acompishment of doing all myself. G
[img][/img] 1977 KZ1000A1
Please Log in or Create an account to join the conversation.
- timebomb33
-
- Offline
- User
-

Registered
- Posts: 4277
- Thanks: 10
Re: 1977 KZ1000 A1
14 Jan 2009 17:34
are you happy with how it rides and feels on the road . dyno numbers are just that numbers who cares, if your happy thats all that counts
1973 z1 2-1974z1-a,2-1975z1-b dragbikes1015cc+1393cc, 1977kz1000,1978kz1000,1981kz1000j, 1997 zx-11, 2000 z12r,1428turbo nitrous pro-mod and a shit load of parts thats all for now leader sask.,CANADA
I THINK MY POWERBAND BROKE
I THINK MY POWERBAND BROKE
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
