Top end question
- rdgrnr
-
Topic Author
- Offline
- User
-

Registered
- Posts: 342
- Thanks: 0
Top end question
19 Jan 2009 11:31
Ok,
I am in the middle of taking the head off for a gasket replacement (in-frame), and I am wondering if anyone has a trick for separating the head from the jugs. It doesn't look like the heads/jugs will come off as a single unit while the engine is in-frame. The jug gasket is free, but the head doesn't want to come loose from the jugs...
Any suggestions?
I am in the middle of taking the head off for a gasket replacement (in-frame), and I am wondering if anyone has a trick for separating the head from the jugs. It doesn't look like the heads/jugs will come off as a single unit while the engine is in-frame. The jug gasket is free, but the head doesn't want to come loose from the jugs...
Any suggestions?
77 KZ650B1
80 440 LTD Sold
78 GL1000 Naked Wing Sold
80 CM400E Sold
Brainerd, MN
80 440 LTD Sold
78 GL1000 Naked Wing Sold
80 CM400E Sold
Brainerd, MN
Please Log in or Create an account to join the conversation.
- oldkaws4ever
-
- Offline
- User
-

Registered
- Have no regrets...... You only live once.
- Posts: 1639
- Thanks: 12
Re: Top end question
19 Jan 2009 11:40
A few tap's from a rubber mallet around the edges should do the trick. There are also "Pry" points, to seperate the head and the fugs, but be careful when prying, hope this has helped.
74 Z1a 900 (Apart and making it better than ever)
77 Kz 650b (Threw a rod, going to sandwich in a 900 or 1000 motor)
76 Kz 400d
05 ninja zx-636
81 Kz 750 Ltd
Darien, Illinois
77 Kz 650b (Threw a rod, going to sandwich in a 900 or 1000 motor)
76 Kz 400d
05 ninja zx-636
81 Kz 750 Ltd
Darien, Illinois
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: Top end question
19 Jan 2009 11:49
tripple check to make sure u have ALL of the bolts out.
U can use the end of a short length of 2x4 wood, say about 6" long. place the wood on the head and hit upwards with a hammer on the wood.
Hope this helps.
U can use the end of a short length of 2x4 wood, say about 6" long. place the wood on the head and hit upwards with a hammer on the wood.
Hope this helps.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- rdgrnr
-
Topic Author
- Offline
- User
-

Registered
- Posts: 342
- Thanks: 0
Re: Top end question
19 Jan 2009 12:08
mark1122 wrote:
I did the tapping with a mallet, and the jugs came with the head. Anyone with a pic of the pry points. I already snapped a fin near the #4 intake:angry:
Also, anyone have a OEM manual? I have a Haynes, but it's not as comprehensive and the pics suck...
tripple check to make sure u have ALL of the bolts out.
U can use the end of a short length of 2x4 wood, say about 6" long. place the wood on the head and hit upwards with a hammer on the wood.
Hope this helps.
I did the tapping with a mallet, and the jugs came with the head. Anyone with a pic of the pry points. I already snapped a fin near the #4 intake:angry:
Also, anyone have a OEM manual? I have a Haynes, but it's not as comprehensive and the pics suck...
77 KZ650B1
80 440 LTD Sold
78 GL1000 Naked Wing Sold
80 CM400E Sold
Brainerd, MN
80 440 LTD Sold
78 GL1000 Naked Wing Sold
80 CM400E Sold
Brainerd, MN
Please Log in or Create an account to join the conversation.
- trianglelaguna
-
- Offline
- User
-

Registered
- New and improved - extra strength
- Posts: 8019
- Thanks: 236
Re: Top end question
19 Jan 2009 12:26
limited exp here but are you sure you got all the bolts outta the head... 900s have two little 6mm bolts on the ends outside the outer sparkplugs as well as the heads stud "nuts"...bummer on the fin i feel your angst on that one.....good luck
1976 KZ900
2003 ZX12R
2007 FZ1000
2004 ninja 250R for wife
2003 ZX12R
2007 FZ1000
2004 ninja 250R for wife
Please Log in or Create an account to join the conversation.
- HerrDeacon
-
- Offline
- User
-

Registered
- Posts: 642
- Thanks: 1
Re: Top end question
19 Jan 2009 12:41
I just took mine off my 650 and there are two bolts in the timing chain tunnel. Did you get those. They are on either end of the tunnel (i.e. front and back). Let me know if you need a pic.
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Top end question
19 Jan 2009 12:50
trianglelaguna wrote:
Kawi hides small bolts in wierd places that help keep the head from seeping oil. Look and ye shall find.....limited exp here but are you sure you got all the bolts outta the head... 900s have two little 6mm bolts on the ends outside the outer sparkplugs as well as the heads stud "nuts"...bummer on the fin i feel your angst on that one.....good luck
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- mariozappa
-
- Offline
- User
-

Registered
- Posts: 896
- Thanks: 8
Re: Top end question
19 Jan 2009 13:03I just took mine off my 650 and there are two bolts in the timing chain tunnel. Did you get those. They are on either end of the tunnel (i.e. front and back).
That's what I was thinking.
1977 KZ650C1
and the KZ650/KZ750 Conversion
and the KZ650/KZ750 Conversion
Please Log in or Create an account to join the conversation.
- rdgrnr
-
Topic Author
- Offline
- User
-

Registered
- Posts: 342
- Thanks: 0
Re: Top end question
19 Jan 2009 13:26
HerrDeacon wrote:
:blush: out now....head is off
..since I broke loose the jug/case gasket, it looks like the jugs need to come off as well...any advice before I proceed?
I'm thinking maybe slow down a bit til I get an OE manual..anyone have one on file?
Thanks everyone for the input:)
I just took mine off my 650 and there are two bolts in the timing chain tunnel. Did you get those. They are on either end of the tunnel (i.e. front and back). Let me know if you need a pic.
:blush: out now....head is off
..since I broke loose the jug/case gasket, it looks like the jugs need to come off as well...any advice before I proceed?
I'm thinking maybe slow down a bit til I get an OE manual..anyone have one on file?
Thanks everyone for the input:)
77 KZ650B1
80 440 LTD Sold
78 GL1000 Naked Wing Sold
80 CM400E Sold
Brainerd, MN
80 440 LTD Sold
78 GL1000 Naked Wing Sold
80 CM400E Sold
Brainerd, MN
Please Log in or Create an account to join the conversation.
- trianglelaguna
-
- Offline
- User
-

Registered
- New and improved - extra strength
- Posts: 8019
- Thanks: 236
Re: Top end question
19 Jan 2009 13:43
when you scroll on the kz info at the top do you see anything in the filbase for your bike...just a thought
1976 KZ900
2003 ZX12R
2007 FZ1000
2004 ninja 250R for wife
2003 ZX12R
2007 FZ1000
2004 ninja 250R for wife
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: Top end question
19 Jan 2009 13:56
what model ,cc" are u working on ?:side:
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- rdgrnr
-
Topic Author
- Offline
- User
-

Registered
- Posts: 342
- Thanks: 0
Re: Top end question
19 Jan 2009 14:04
mark1122 wrote:
sorry, I forgot to mention that I am working on my 77 650B1
what model ,cc" are u working on ?:side:
sorry, I forgot to mention that I am working on my 77 650B1
77 KZ650B1
80 440 LTD Sold
78 GL1000 Naked Wing Sold
80 CM400E Sold
Brainerd, MN
80 440 LTD Sold
78 GL1000 Naked Wing Sold
80 CM400E Sold
Brainerd, MN
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
