top head gasket leaking.
- kzmarvo
-
Topic Author
- Offline
- User
-

Registered
- Posts: 344
- Thanks: 0
top head gasket leaking.
10 Feb 2009 14:21
Gonna replace the top head gasket on my bike,its leaking. Any tips one the type of gasket to buy? I never replaced a head gasket on a kz but am very mechanical so i think i'll be ok,that and i have a repair book:) Any advice feel free:)
Watch it folks,i have sticky fingers when it comes to a nice looking set of handle bars:)
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: top head gasket leaking.
10 Feb 2009 15:07 - 10 Feb 2009 15:35
kzmarvo wrote:
top head gasket -- the head gasket lies between the head and cylinder block. The valve cover gasket lies between the valve cover and head. Am wondering if top head gasket is actually referring to the valve cover gasket.
If not already done, before replacing head gasket, would first - - -
Torque all head nuts to specs, and perform leak-down test to confirm source of leak.
Double-check other possible common leak sources:
Tach drive;
Valve cover gasket;
Half-moon cam plugs;
Exhaust ports;
Oil cooler hose connections.
Clean and thoroughly dry engine without starting it. Next, start engine and use flashlight to closely inspect and determine exact source of leak.
Z1E probably carries the head gasket. Where applicable, would use the oem style two piece gasket (not copper).
Good Luck!
P.S. If only concerned with the valve cover gasket, Z1E may also have it available. Same for the half-moon cam end plugs.
Gonna replace the top head gasket on my bike,its leaking. Any tips one the type of gasket to buy? I never replaced a head gasket on a kz but am very mechanical so i think i'll be ok,that and i have a repair book:) Any advice feel free:)
top head gasket -- the head gasket lies between the head and cylinder block. The valve cover gasket lies between the valve cover and head. Am wondering if top head gasket is actually referring to the valve cover gasket.
If not already done, before replacing head gasket, would first - - -
Torque all head nuts to specs, and perform leak-down test to confirm source of leak.
Double-check other possible common leak sources:
Tach drive;
Valve cover gasket;
Half-moon cam plugs;
Exhaust ports;
Oil cooler hose connections.
Clean and thoroughly dry engine without starting it. Next, start engine and use flashlight to closely inspect and determine exact source of leak.
Z1E probably carries the head gasket. Where applicable, would use the oem style two piece gasket (not copper).
Good Luck!
P.S. If only concerned with the valve cover gasket, Z1E may also have it available. Same for the half-moon cam end plugs.
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 10 Feb 2009 15:35 by Patton.
Please Log in or Create an account to join the conversation.
- keith1
-
- Offline
- User
-

Registered
- Posts: 1646
- Thanks: 3
Re: top head gasket leaking.
10 Feb 2009 19:19
Patton wrote:
what patton said.......my bike was leaking from all of the above when i got it!!!lol
if its really smeg covered, simple green motor cold and try to find the source....good luck....
kzmarvo wrote:Gonna replace the top head gasket on my bike,its leaking. Any tips one the type of gasket to buy? I never replaced a head gasket on a kz but am very mechanical so i think i'll be ok,that and i have a repair book:) Any advice feel free:)
top head gasket -- the head gasket lies between the head and cylinder block. The valve cover gasket lies between the valve cover and head. Am wondering if top head gasket is actually referring to the valve cover gasket.
If not already done, before replacing head gasket, would first - - -
Torque all head nuts to specs, and perform leak-down test to confirm source of leak.
Double-check other possible common leak sources:
Tach drive;
Valve cover gasket;
Half-moon cam plugs;
Exhaust ports;
Oil cooler hose connections.
Clean and thoroughly dry engine without starting it. Next, start engine and use flashlight to closely inspect and determine exact source of leak.
Z1E probably carries the head gasket. Where applicable, would use the oem style two piece gasket (not copper).
Good Luck!
P.S. If only concerned with the valve cover gasket, Z1E may also have it available. Same for the half-moon cam end plugs.
what patton said.......my bike was leaking from all of the above when i got it!!!lol
if its really smeg covered, simple green motor cold and try to find the source....good luck....
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: top head gasket leaking.
10 Feb 2009 20:20
To locate a suspected oil leak I first throughly degrease the engine,wash again with some liquid clothes soap in a high concentrate, rinse well,dry using low pressure air, and then spray the aeresol foot powder and start the engine.
The foot powder will reveal where the oil leak is and is easy washed off with soap and water afterwards.
The foot powder will reveal where the oil leak is and is easy washed off with soap and water afterwards.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: top head gasket leaking.
10 Feb 2009 21:50 - 10 Feb 2009 21:53
MFolks wrote:
Good call, and thanks for that info!
In the past I've suggested using underarm spray deodorant with powder, believed since discontinued due to health concerns. But had not thought about the powdered foot spray.
To locate a suspected oil leak I first throughly degrease the engine,wash again with some liquid clothes soap in a high concentrate, rinse well,dry using low pressure air, and then spray the aeresol foot powder and start the engine.
The foot powder will reveal where the oil leak is and is easy washed off with soap and water afterwards.
Good call, and thanks for that info!
In the past I've suggested using underarm spray deodorant with powder, believed since discontinued due to health concerns. But had not thought about the powdered foot spray.
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 10 Feb 2009 21:53 by Patton.
Please Log in or Create an account to join the conversation.
- kzmarvo
-
Topic Author
- Offline
- User
-

Registered
- Posts: 344
- Thanks: 0
Re: top head gasket leaking.
10 Feb 2009 22:17
thanks for the advice,its for sure the top head gasket. What is the labor on this,shop told me 6 hours.
Watch it folks,i have sticky fingers when it comes to a nice looking set of handle bars:)
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: top head gasket leaking.
10 Feb 2009 22:26
kzmarvo wrote:
What year and model KZ?
thanks for the advice,its for sure the top head gasket. What is the labor on this,shop told me 6 hours.
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: top head gasket leaking.
10 Feb 2009 22:30 - 10 Feb 2009 22:32
kzmarvo wrote:
Six hours sounds pretty reasonable. You have to R+R the gas tank, carburetors, coils, exhaust pipes, head, camshafts, cam chain, etc. You will want to lap the valves and replace the valve guide seals while the head is off, the added cost to do it is minimal if you are pulling the head.thanks for the advice,its for sure the top head gasket. What is the labor on this,shop told me 6 hours.
1979 KZ-750 Twin
Last edit: 10 Feb 2009 22:32 by bountyhunter.
Please Log in or Create an account to join the conversation.
- dshelly
-
- Offline
- User
-

Registered
- Posts: 258
- Thanks: 5
Re: top head gasket leaking.
11 Feb 2009 05:46
If you are new at this and going to do it yourself. First, get a manual. Unless you already have one. They are worth every penny. especially the factory ones.
So while I'm at it. What does everybody think of spraying a head gasket with Permatex High Tack? You know ,the red sticky stuff. We used to use it on our dirt bike when we were kids. It worked great! Never had a leak.
So while I'm at it. What does everybody think of spraying a head gasket with Permatex High Tack? You know ,the red sticky stuff. We used to use it on our dirt bike when we were kids. It worked great! Never had a leak.
Occupation:Machinist 25+ exp.
'77 Kz1000B1
'78 Kz1000A2
'76 Kz900LTD
'77 Kz1000B1
'78 Kz1000A2
'76 Kz900LTD
Please Log in or Create an account to join the conversation.
- SebRain77
-
- Offline
- User
-

Registered
- When in doubt, gas it!
- Posts: 86
- Thanks: 0
Re: top head gasket leaking.
11 Feb 2009 17:43
Ok, well this is good timing, I'm also going to replace my 650's head gasket, so the info provided above is great. I'm guessing using baby powder would have the same result in trying to pinpoint the leak?
Now onto a related question (without hijacking this thread): how complicated of a job is it to do it myself? I have some mechanical skills, I have a Clymer manual, and I'm pretty patient!
Cannot afford the shop's labour costs, hence the reason to try it myself.
Now onto a related question (without hijacking this thread): how complicated of a job is it to do it myself? I have some mechanical skills, I have a Clymer manual, and I'm pretty patient!
Cannot afford the shop's labour costs, hence the reason to try it myself.
**************************************************
Ever hit the pavement? I did, put that gear on!
1977 KZ 650C1 - First bike, ever! For sale - or not!?!?
2004 Z750 - More power than I'll ever need...
Gatineau, Qc, Canada eh!
Ever hit the pavement? I did, put that gear on!
1977 KZ 650C1 - First bike, ever! For sale - or not!?!?
2004 Z750 - More power than I'll ever need...
Gatineau, Qc, Canada eh!
Please Log in or Create an account to join the conversation.
- kzmarvo
-
Topic Author
- Offline
- User
-

Registered
- Posts: 344
- Thanks: 0
Re: top head gasket leaking.
11 Feb 2009 18:58
bike is a 1973 kz900 engine is a 1977kz 1000.
Watch it folks,i have sticky fingers when it comes to a nice looking set of handle bars:)
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: top head gasket leaking.
11 Feb 2009 21:49
SebRain77 wrote:
I can tell you for sure it would be impossible to do mine without the factory service manual. I don't think Clymers are worth much.
Ok, well this is good timing, I'm also going to replace my 650's head gasket, so the info provided above is great. I'm guessing using baby powder would have the same result in trying to pinpoint the leak?
Now onto a related question (without hijacking this thread): how complicated of a job is it to do it myself? I have some mechanical skills, I have a Clymer manual, and I'm pretty patient!
Cannot afford the shop's labour costs, hence the reason to try it myself.
I can tell you for sure it would be impossible to do mine without the factory service manual. I don't think Clymers are worth much.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
