KZ550 Project - Need opinions

  • insignia100
  • insignia100's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 38
  • Thanks: 0

KZ550 Project - Need opinions

28 Mar 2009 21:29
#276256
Okay, a little bit of background info. I bought this bike back in November and, due to school, weather, and other obligations, it sat without running until February. When I finally got a chance to fire it up (on a warmish day, of course) and found that it was running rough, missing on one cylinder, and needed the choke on full to stay running. First order of business was to replace all the spark plugs. Well, that didn't help my issues, but they needed replacing anyway.

Next I pulled the carbs and gave them a cleaning. The float bowls were surprisingly clean, so I focused mainly on the pilot and main jets. Cleaned them up good, put the carbs back in, and she fired right up. The carb cleaning fixed the sluggish throttle response and reliance on the choke to keep running.

Here's a video I shot today after putting the carbs back in:



Now I've got another issue to work on. You can very clearly hear a clacking/rattling sound coming from the right side of the engine. The sound goes away after, maybe, 2000 RPM. I'm figuring its either a valve adjustment issue or, more likely, a cam chain adjustment issue.

Any comments?
1983 Kawasaki KZ550

Please Log in or Create an account to join the conversation.

  • kaw-62046
  • kaw-62046's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 96
  • Thanks: 0

Re: KZ550 Project - Need opinions

28 Mar 2009 21:47
#276265
Sounds like it running on 3 cylinders,check the head pipes to see if all 4 are hot.Also sounds like some cam chain noise.

Please Log in or Create an account to join the conversation.

  • PLUMMEN
  • PLUMMEN's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7983
  • Thanks: 104

Re: KZ550 Project - Need opinions

28 Mar 2009 21:55
#276267
definately sounds like a dead cylinder on the right pipe ;)
Still recovering,some days are better than others.

Please Log in or Create an account to join the conversation.

  • Mark Wing
  • Mark Wing's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1695
  • Thanks: 22

Re: KZ550 Project - Need opinions

28 Mar 2009 22:01
#276270
Dito.
Mark
Jesus loves you Everyone else thinks your an ***

77 KZ650 C1 with ZX7 forks, GPZ mono rear, wider 18 police wheels and Yoshimura motor.

Yorba Linda Cal.

Please Log in or Create an account to join the conversation.

  • timebomb33
  • timebomb33's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 4277
  • Thanks: 10

Re: KZ550 Project - Need opinions

28 Mar 2009 22:02
#276271
you still have a plugged pilot circuit not just a jet. the knocking sound will clear up after it fires and runs on all 4 and you do a carb sync.
1973 z1 2-1974z1-a,2-1975z1-b dragbikes1015cc+1393cc, 1977kz1000,1978kz1000,1981kz1000j, 1997 zx-11, 2000 z12r,1428turbo nitrous pro-mod and a shit load of parts thats all for now leader sask.,CANADA
I THINK MY POWERBAND BROKE

Please Log in or Create an account to join the conversation.

  • insignia100
  • insignia100's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 38
  • Thanks: 0

Re: KZ550 Project - Need opinions

28 Mar 2009 22:13
#276273
I was afraid the carbs were still the culprit. How would you recommend cleaning the pilot circuit? I actually tried to completely take the carbs apart, but the screws securing the throttle body (correct term? I dunno...) wouldn't budge. Perhaps spraying some carb cleaner into the pilot air intake (again, not sure if that's the correct terminology)?

I'm going to check the spark plug cables before I remove the carbs again to make sure that's not the problem.
1983 Kawasaki KZ550

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: KZ550 Project - Need opinions

28 Mar 2009 22:24
#276274
The coils and the sparkplug caps all age with heat and time. I'd replace the sparkplug caps first and see if that helps. I think you can get new ones from z1 enterprises.

If you're lucky the sparkplug leads will unscrew from the coils, if not they may be one piece and have to change the coils all though NGK does make a sparkplug lead splice kit.

A can of the fuel additive "Seafoam" will help clean out the carbs. www.seafoamsales.com is their website. You can buy it at Wal Mart in the automotive chemical section,boating supply stores,and auto parts stores.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • insignia100
  • insignia100's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 38
  • Thanks: 0

Re: KZ550 Project - Need opinions

28 Mar 2009 22:34
#276285
Yea, I've actually got a can of Berrymans B12 that I had planned on using in a tank of gas once I got the bike running decently. My only concern is that, if fuel (or maybe air?) isn't getting through the pilot circuit, how will a fuel additive help?
1983 Kawasaki KZ550

Please Log in or Create an account to join the conversation.

  • PLUMMEN
  • PLUMMEN's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7983
  • Thanks: 104

Re: KZ550 Project - Need opinions

28 Mar 2009 22:44
#276288
dump a can of seafoam in the tank with some new gas and take it out and run it hard around town a little bit(let it rev and stay in lower gears as much as possible)to let the carb cleaner do its thing,sometimes thats all it takes.in extreme cases sometimes you can cheat by holding your hand over the inlet side of carbs and cracking the throttle to blow them out also.B)
Still recovering,some days are better than others.

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: KZ550 Project - Need opinions

28 Mar 2009 22:47
#276290
Depending on how clogged it is a fuel cleaner like Berrymans or Seafoam will dissolve the varnish from old gasoline over time. You might have to drop the carbs and carefully dig out the blockage with some very fine stiff wire. I use a set of torch tip cleaners the welders use when the torches act up. I think you can buy them at a welding supply store.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum