Question for Leon

  • T_Dub
  • T_Dub's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 1441
  • Thanks: 26

Question for Leon

03 Apr 2009 12:04
#278082
Other people can probably answer this but I know Leon can. When boring cylinders, what clearance do you leave between the walls and the pistons before the hone? I want to bore my cylinders myself and get the local shop to hone, because they have the correct machine. I really dont see the need to pay someone over $100 to bore though when I can do that myself easily.
1977 KZ650B1
-810cc
-Cavanaugh Racing Head
-Mikuni RS34's
-GPR Muffler

Please Log in or Create an account to join the conversation.

  • arai59
  • arai59's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Question for Leon

03 Apr 2009 12:27 - 03 Apr 2009 12:28
#278086
You have the correct machine to bore cyclinders ? Boring is precision work. Honing is nothing.
Last edit: 03 Apr 2009 12:28 by arai59.

Please Log in or Create an account to join the conversation.

  • T_Dub
  • T_Dub's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 1441
  • Thanks: 26

Re: Question for Leon

03 Apr 2009 12:33 - 03 Apr 2009 12:35
#278087
I get within a tolerance of .005" normally, I'd imagine thats good enough. .002" is possible if I'm careful.
1977 KZ650B1
-810cc
-Cavanaugh Racing Head
-Mikuni RS34's
-GPR Muffler
Last edit: 03 Apr 2009 12:35 by T_Dub.

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Question for Leon

03 Apr 2009 13:38
#278107
T_Dub wrote:
I get within a tolerance of .005" normally, I'd imagine thats good enough. .002" is possible if I'm careful.
.005" is definitely not good enough for boring cylinders. Standard clearance spec for piston to cylinder on mine is .0016" - .0028". BTW: pistons taper top to bottem and are widest at the skirt. The machine shop that did mine required I give them the pistons so they could measure them, then they marked them to the hole they were matched to.
1979 KZ-750 Twin

Please Log in or Create an account to join the conversation.

  • T_Dub
  • T_Dub's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 1441
  • Thanks: 26

Re: Question for Leon

03 Apr 2009 13:42
#278109
Alrighty, I'll get the shop to do it then, after I get my pistons, so they can measure. I actually meant .0005, but it'd suck if I screwed it up.
1977 KZ650B1
-810cc
-Cavanaugh Racing Head
-Mikuni RS34's
-GPR Muffler

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: Question for Leon

03 Apr 2009 14:11
#278113
The pistons are measured near the bottom. i dont think all manufacturers use the same spot. J&E measures 1/2" up from the bottom, front to back. they may be oval shaped as well.B)
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum