Help! Removing stubborn old gasket
- nob_1100
-
Topic Author
- Offline
- User
-

Registered
- Posts: 26
- Thanks: 0
Help! Removing stubborn old gasket
21 May 2009 21:55
I just took off the cylinder off my 83 1100 Ltd motor and I was hugely disappointed to see the old cylinder/crankcase gasket (paper type) stuck firmly on top of the crankcase. I've been trying with a razor blade but it's chipping away the aluminum edges more than removing the gasket itself. I gave a try to paint remover, bud it didn't work. The cylinder studs that get in the way aren't particularly helpful. I don't want to remove the motor from the bike, so soaking the entire surface in a solvent isn't an option for me. Please help!
83 1100 Ltd
Please Log in or Create an account to join the conversation.
- timebomb33
-
- Offline
- User
-

Registered
- Posts: 4277
- Thanks: 10
Re: Help! Removing stubborn old gasket
21 May 2009 22:04
crc makes a great product called gasket remover also permatex or loctite makes the same thing spray it on walk away for 5 or 10 min. and it softens the old gasket right up you might have to do this a few times but it will come off take your time and change blades often and it will all work out for you.
1973 z1 2-1974z1-a,2-1975z1-b dragbikes1015cc+1393cc, 1977kz1000,1978kz1000,1981kz1000j, 1997 zx-11, 2000 z12r,1428turbo nitrous pro-mod and a shit load of parts thats all for now leader sask.,CANADA
I THINK MY POWERBAND BROKE
I THINK MY POWERBAND BROKE
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Help! Removing stubborn old gasket
21 May 2009 23:25 - 21 May 2009 23:28
nob_1100 wrote:
I tried motor oil, brake fluid, gasket remover, acetone, and everything else. You need to scrape but don't gouge down into the surface. It will come, took a couple of hours to do a good job.
BTW, they seal that gasket with a product like 3-bond which is designed to be impervious to solvent and virtually indestructible to prevent leaks.... but it is a bugger to get off. It had the cylinder on mine sealed down so tight I almost had to break the cylinder to pry it up.
Use a single sided blade held straight up scraping along. There is no easy fix, it's a miserable job. pack shop rags down into the crankcase to keep the junk from falling down, and use a vacuum hose to slurp up as much as possible of the debris as you go along.I just took off the cylinder off my 83 1100 Ltd motor and I was hugely disappointed to see the old cylinder/crankcase gasket (paper type) stuck firmly on top of the crankcase. I've been trying with a razor blade but it's chipping away the aluminum edges more than removing the gasket itself. I gave a try to paint remover, bud it didn't work. The cylinder studs that get in the way aren't particularly helpful. I don't want to remove the motor from the bike, so soaking the entire surface in a solvent isn't an option for me. Please help!
I tried motor oil, brake fluid, gasket remover, acetone, and everything else. You need to scrape but don't gouge down into the surface. It will come, took a couple of hours to do a good job.
BTW, they seal that gasket with a product like 3-bond which is designed to be impervious to solvent and virtually indestructible to prevent leaks.... but it is a bugger to get off. It had the cylinder on mine sealed down so tight I almost had to break the cylinder to pry it up.
1979 KZ-750 Twin
Last edit: 21 May 2009 23:28 by bountyhunter.
Please Log in or Create an account to join the conversation.
- athlonwirez
-
- Offline
- User
-

Registered
- Posts: 56
- Thanks: 0
Re: Help! Removing stubborn old gasket
22 May 2009 06:15
I don't know about this particular case, however, I have always had good luck using a good wood chisel to get gaskets off aluminum surfaces.
1978 LTD Partial Restoration in Process. (Do not have orginal exhaust)
Please Log in or Create an account to join the conversation.
- nob_1100
-
Topic Author
- Offline
- User
-

Registered
- Posts: 26
- Thanks: 0
Re: Help! Removing stubborn old gasket
22 May 2009 21:59
Thanks guys. I tried something similar to gasket remover, and while it worked a little better than paint remover, it ultimately didn't prevail. At the end, a straight blade did the trick. Thanks bountyhunter. But it took me 5 hours to scrape off the gasket...and some metal :X. What a nightmare. I'm thinking about putting the new gasket dry without liquid sealant so that when I need to crack it open next time I will not have to go through the pain I went through this time. I don't know this is a good idea, though.
83 1100 Ltd
Please Log in or Create an account to join the conversation.
- timebomb33
-
- Offline
- User
-

Registered
- Posts: 4277
- Thanks: 10
Re: Help! Removing stubborn old gasket
22 May 2009 22:18
you shouldn't be using any sealer on gaskets anyway you always put them in dry. gaskets will over time adhere to the gasket surface's it is a fact of life.so get used to scraping them.
1973 z1 2-1974z1-a,2-1975z1-b dragbikes1015cc+1393cc, 1977kz1000,1978kz1000,1981kz1000j, 1997 zx-11, 2000 z12r,1428turbo nitrous pro-mod and a shit load of parts thats all for now leader sask.,CANADA
I THINK MY POWERBAND BROKE
I THINK MY POWERBAND BROKE
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Help! Removing stubborn old gasket
22 May 2009 22:47 - 22 May 2009 22:47
nob_1100 wrote:
As for leaving it dry? The factory sure didn't on mine, it was sealed with 3-bond type of adhesive. I used the black ultra HI-temp gasket sealer when I did it, seals very well but isn't as hard to remove. I am always afraid that the lip might be nicked or scratched during gasket removal and without sealer, it will leak oil.
You did pretty good. I recall it took me about 3+ hours to get the base gasket off JUST the crankcase side when I did my 750 twin. Probably 1+ hour to clean the cylinder surface.Thanks guys. I tried something similar to gasket remover, and while it worked a little better than paint remover, it ultimately didn't prevail. At the end, a straight blade did the trick. Thanks bountyhunter. But it took me 5 hours to scrape off the gasket...and some metal :X. What a nightmare. I'm thinking about putting the new gasket dry without liquid sealant so that when I need to crack it open next time I will not have to go through the pain I went through this time. I don't know this is a good idea, though.
As for leaving it dry? The factory sure didn't on mine, it was sealed with 3-bond type of adhesive. I used the black ultra HI-temp gasket sealer when I did it, seals very well but isn't as hard to remove. I am always afraid that the lip might be nicked or scratched during gasket removal and without sealer, it will leak oil.
1979 KZ-750 Twin
Last edit: 22 May 2009 22:47 by bountyhunter.
Please Log in or Create an account to join the conversation.
- donthekawguy
-
- Offline
- User
-

Registered
- Posts: 1911
- Thanks: 8
Re: Help! Removing stubborn old gasket
24 May 2009 23:29
I always use the Permatex stuff. It has always worked good for me and it's cool to watch it bubble up. :laugh:
Rathdrum Idaho
1971 Kawasaki g3ss
1972 Yamaha R5 350
1965 Suzuki Hillbilly
1964 Yamaha 125
1971 Kawasaki g3ss
1972 Yamaha R5 350
1965 Suzuki Hillbilly
1964 Yamaha 125
Please Log in or Create an account to join the conversation.
- timebomb33
-
- Offline
- User
-

Registered
- Posts: 4277
- Thanks: 10
Re: Help! Removing stubborn old gasket
25 May 2009 14:01
all gaskets unless specified should be installed dry you should never have to install them with anytype of bonding agent. especially anytype of silicon product silicon and oils do not mix if goes on to heavy and it oozes out it and it will it will react with the hot oils and combustion gases and end up everywhere in your engine including oil galleries and could possibly if enough is floatng around plug your oil pump pick-up.
1973 z1 2-1974z1-a,2-1975z1-b dragbikes1015cc+1393cc, 1977kz1000,1978kz1000,1981kz1000j, 1997 zx-11, 2000 z12r,1428turbo nitrous pro-mod and a shit load of parts thats all for now leader sask.,CANADA
I THINK MY POWERBAND BROKE
I THINK MY POWERBAND BROKE
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Help! Removing stubborn old gasket
25 May 2009 14:06 - 25 May 2009 14:08
timebomb33 wrote:
gasket sealing agents should NEVER be used that way: you use a very thin bead and assemble wet, and apply light torque which will thin down the sealant to a VERY thin layer. As I said, my '79 KZ750 came from the factory with a permanent type sealer on the base gasket similar to 3-bond. That is one gasket you NEVER want to have a leak on because you have to tear the whole top of the engine off to fix it.if goes on too heavy and it oozes out, it will react with the hot oils and combustion gases and end up everywhere in your engine including oil galleries and could possibly if enough is floatng around plug your oil pump pick-up.
1979 KZ-750 Twin
Last edit: 25 May 2009 14:08 by bountyhunter.
Please Log in or Create an account to join the conversation.
- clone5
-
- Offline
- User
-

Registered
- Posts: 15
- Thanks: 0
Re: Help! Removing stubborn old gasket
10 Mar 2012 07:03
The Permatex website does not list a gasket remover
What is this stuff?
What is this stuff?
Please Log in or Create an account to join the conversation.
- clone5
-
- Offline
- User
-

Registered
- Posts: 15
- Thanks: 0
Re: Help! Removing stubborn old gasket
10 Mar 2012 07:11
To be sure, I have stripped the engine down.
Head has been reco'd. New valve seats etc
Last step holding up the rebuild is the amazingly bonded base gasket!! Holy shyte!! This thing does not want to soak off in turps and resists the blade treatment.
I hear of these things like Permatex and CRC etc and also using paint stripper. These are my next options. Can the gasket be burned off?
Head has been reco'd. New valve seats etc
Last step holding up the rebuild is the amazingly bonded base gasket!! Holy shyte!! This thing does not want to soak off in turps and resists the blade treatment.
I hear of these things like Permatex and CRC etc and also using paint stripper. These are my next options. Can the gasket be burned off?
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
