Need a part, HELP!!! Oil Pan Plug for 650...

  • Tyler
  • Tyler's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 845
  • Thanks: 92

Need a part, HELP!!! Oil Pan Plug for 650...

12 Jul 2009 19:06
#306579
I just got the rebuilt engine back in my 1980 KZ 650 and I have a probelm. Originaly the previous owner had an oil cooler on this motor and I am not running one. I need the M17 x 1.25 allen head set screw that plugs the rear of the oil pan. Any of you with an oil cooler know what I am talking about. This is an impossible part to buy as nothing I have found suggests that M17 by 1.25 is even made for anything and my lathe can't cut metric threads. If anyone has this plug or even a whole oil pan with one let me know. My other option is to swap oil pans with and older engine but I don't want to go through that if I can avoid it. Prior to 1980 kawasaki used a M18 hex head plug, after that is was changed to a M17 plug.
If I knew what I was doing all the time life wouldn't be any fun.

'80 KZ650 E 700cc, dyna ignition and coils, frame up restoration, daily driver
'81 KZ1300 A3 full restoration, custom big bore pistons, 1400cc 6 cylinder super bike
"77 KZ650 B1 - Barn Find, work in progeress
"74 Yamaha DT 400 Enduro

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Need a part, HELP!!! Oil Pan Plug for 650...

12 Jul 2009 19:40
#306605
I'm not sure what M17 X 1.25 is. I would probably just drill the hole out and tap it to the next size up that I had and then put a bolt in it with red loctite and it will be plugged forever.
1979 KZ-750 Twin

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: Need a part, HELP!!! Oil Pan Plug for 650...

12 Jul 2009 20:26
#306633
I looked at the Kawasaki.com parts diagrams for the 1980 KZ650-F1 and E1, but I didn't see a plug at the rear of the pan. I do see one on the 1979 KZ650C3 and earlier KZ650 oil pans. Are you sure this hole wasn't drilled by the previous owner? If not, do you have a part number or diagram that shows the plug? Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)

Please Log in or Create an account to join the conversation.

  • Tyler
  • Tyler's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 845
  • Thanks: 92

Re: Need a part, HELP!!! Oil Pan Plug for 650...

12 Jul 2009 21:25
#306651
Nope its the factory plug that is removed from the rear of the pan when adding an oil cooler. It is not available from Kawasaki. I doubt anyone would "make" that thread as a 1.25 pitch 17mm metric tap is VERY uncommon.


What I can do is cut the barb off of the Lockheart fitting and drill and tap it for a pipe plug. That way I don't have to pull the pan down again.

Just confounds me that Kaw would use such an odd ball thread and diameter, all previous models used a 18mm fine thread bolt, why they changed is beyond me...
If I knew what I was doing all the time life wouldn't be any fun.

'80 KZ650 E 700cc, dyna ignition and coils, frame up restoration, daily driver
'81 KZ1300 A3 full restoration, custom big bore pistons, 1400cc 6 cylinder super bike
"77 KZ650 B1 - Barn Find, work in progeress
"74 Yamaha DT 400 Enduro

Please Log in or Create an account to join the conversation.

  • Mark Wing
  • Mark Wing's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1695
  • Thanks: 22

Re: Need a part, HELP!!! Oil Pan Plug for 650...

13 Jul 2009 00:01
#306677
I've got one, PM me your address and I'll send it to you.

Mark
Jesus loves you Everyone else thinks your an ***

77 KZ650 C1 with ZX7 forks, GPZ mono rear, wider 18 police wheels and Yoshimura motor.

Yorba Linda Cal.

Please Log in or Create an account to join the conversation.

  • Tyler
  • Tyler's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 845
  • Thanks: 92

Re: Need a part, HELP!!! Oil Pan Plug for 650...

13 Jul 2009 10:08
#306709
Awesome, thanks man!!! B)
If I knew what I was doing all the time life wouldn't be any fun.

'80 KZ650 E 700cc, dyna ignition and coils, frame up restoration, daily driver
'81 KZ1300 A3 full restoration, custom big bore pistons, 1400cc 6 cylinder super bike
"77 KZ650 B1 - Barn Find, work in progeress
"74 Yamaha DT 400 Enduro

Please Log in or Create an account to join the conversation.

  • Bluemeanie
  • Bluemeanie's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 2516
  • Thanks: 15

Re: Need a part, HELP!!! Oil Pan Plug for 650...

14 Jul 2009 20:06
#307102
Mark Wing wrote:
I've got one, PM me your address and I'll send it to you.

Mark

Of course you do, Mark! :woohoo:
1980 KZ650F1, Bought new out the door for $2,162.98!

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum