cam end caps
- Old Man Rock
-
- Offline
- User
-

Registered
- Posts: 6071
- Thanks: 225
Re: cam end caps
28 Sep 2009 05:44
I used the 3 Bond Engine Case sealer I had left over...
Figured if it seals for leaks between the engine cases should work for end caps with no problems... Was correct, no leaks...
Now for my question, how the hell did these get "Sucked" in for they should be lipped on the bottom side?
With the valve cover firmly in place they wouldn't be able to tilt or anything as such as well... I don't get it unless rubber caps then sure I get it but aluminum.... :S
Ah well....
OMR
Figured if it seals for leaks between the engine cases should work for end caps with no problems... Was correct, no leaks...
Now for my question, how the hell did these get "Sucked" in for they should be lipped on the bottom side?
With the valve cover firmly in place they wouldn't be able to tilt or anything as such as well... I don't get it unless rubber caps then sure I get it but aluminum.... :S
Ah well....
OMR
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
Please Log in or Create an account to join the conversation.
- 531blackbanshee
-
- Offline
- Vendor
-

Vendors
- Posts: 7442
- Thanks: 796
Re: cam end caps
28 Sep 2009 10:42
damn omr,you need to read each post twice before you reply (your oldtimers disease is gettin bad).he had the rubber ones not the alu ones.i had the same thing happen when i bought some rubber ones from
www.partsnmore.com/cat_index.php?model=k...1000&category=engine
i installed them with loctite gasket eliminator and then fired it up and sucked em in.i think the trick is to let whatever sealer you use setup first.i bought alum ones and haven't looked back.
we just installed the rubber ones in my buddies bike three weeks ago and let them setup while we were installing the engine and they have held good.
leon holmes
i installed them with loctite gasket eliminator and then fired it up and sucked em in.i think the trick is to let whatever sealer you use setup first.i bought alum ones and haven't looked back.
we just installed the rubber ones in my buddies bike three weeks ago and let them setup while we were installing the engine and they have held good.
leon holmes
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
Please Log in or Create an account to join the conversation.
- MentalMike
-
- Offline
- User
-

Registered
- God Bless America!
- Posts: 210
- Thanks: 0
Re: cam end caps
28 Sep 2009 12:25
keith1 wrote:
I use the same a keith and never had a problem.
did you put any sealer on plugs?...i use 3 bond 1194 and no probs....i have the same plugs...how far did they go back in? something doesnt sound right.....
I use the same a keith and never had a problem.
I swear to God, it's like I live in a trailer of common sense, and stare out the window at a tornado of stupidity.
1976 Kawasaki KZ900
1978 Kawasaki KZ1000A
1978 Kawasaki KZ650 C
1984 Kawasaki ZN1100 LTD
1985 Kawasaki ZX900A2 GPZ (2)
1985 Kawasaki ZL900 Eliminator
2013 Kawasaki C14 Concours
1976 Kawasaki KZ900
1978 Kawasaki KZ1000A
1978 Kawasaki KZ650 C
1984 Kawasaki ZN1100 LTD
1985 Kawasaki ZX900A2 GPZ (2)
1985 Kawasaki ZL900 Eliminator
2013 Kawasaki C14 Concours
Please Log in or Create an account to join the conversation.
- Old Man Rock
-
- Offline
- User
-

Registered
- Posts: 6071
- Thanks: 225
Re: cam end caps
28 Sep 2009 17:56
Black-Banshee... :laugh: :laugh: :laugh: :laugh:
Damn Walgreen specials.... :blink: :laugh:
Now where the hell does he say he had rubber in his opening statement/question.... :blink:
As I re-read, I came across this "yes i used sealer. bbut it seems like the caps were just a hair to small when i fired it up 3 of them sucked in and started leaking the 4th one the metal inside the cap came completely out of the cap."
Again... I assumed aluminum.... Either way, Old & stupid ok, use sealer, insure the top of the caps are square/straight with the top of the head deck...
Note to they self: Find Facial image of Banshee for Photo Chopping.... :evil:
Now where the hell does he say he had rubber in his opening statement/question.... :blink:
As I re-read, I came across this "yes i used sealer. bbut it seems like the caps were just a hair to small when i fired it up 3 of them sucked in and started leaking the 4th one the metal inside the cap came completely out of the cap."
Again... I assumed aluminum.... Either way, Old & stupid ok, use sealer, insure the top of the caps are square/straight with the top of the head deck...
Note to they self: Find Facial image of Banshee for Photo Chopping.... :evil:
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
Please Log in or Create an account to join the conversation.
- keith1
-
- Offline
- User
-

Registered
- Posts: 1646
- Thanks: 3
Re: cam end caps
28 Sep 2009 18:06
Old Man Rock wrote:
dave, settle down and try to keep up!!!:laugh: :woohoo:
Black-Banshee... :laugh: :laugh: :laugh: :laugh:Damn Walgreen specials.... :blink: :laugh:
Now where the hell does he say he had rubber in his opening statement/question.... :blink:
As I re-read, I came across this "yes i used sealer. bbut it seems like the caps were just a hair to small when i fired it up 3 of them sucked in and started leaking the 4th one the metal inside the cap came completely out of the cap."
Again... I assumed aluminum.... Either way, Old & stupid ok, use sealer, insure the top of the caps are square/straight with the top of the head deck...
Note to they self: Find Facial image of Banshee for Photo Chopping.... :evil:
dave, settle down and try to keep up!!!:laugh: :woohoo:
Please Log in or Create an account to join the conversation.
- TerryK
-
- Offline
- User
-

Registered
- Posts: 607
- Thanks: 2
Re: cam end caps
28 Sep 2009 18:34
APE caps are the way to go.
I've seen people put the stock ones in backwards which results in the caps being sucked into the engine.
I've seen people put the stock ones in backwards which results in the caps being sucked into the engine.
1977 KZ1000
GSXR swingarm and rear brake
WM6 rear Akront rim
Wiseco 1075c pistons
33 smoothbores
stage 3 Web Cams
Head porting
Dyna S ignition
Lockhart oil cooler
Wiseco header
1980 Z1R drag bike
1200cc
38 Flatslides, .
500' cams
7" slick
Dyan 4000 SP ignition
etc
Ontario, Canada
GSXR swingarm and rear brake
WM6 rear Akront rim
Wiseco 1075c pistons
33 smoothbores
stage 3 Web Cams
Head porting
Dyna S ignition
Lockhart oil cooler
Wiseco header
1980 Z1R drag bike
1200cc
38 Flatslides, .
500' cams
7" slick
Dyan 4000 SP ignition
etc
Ontario, Canada
Please Log in or Create an account to join the conversation.
- Old Man Rock
-
- Offline
- User
-

Registered
- Posts: 6071
- Thanks: 225
Re: cam end caps
28 Sep 2009 19:52
Keith....
Be nice for I already have your ugly mug... :laugh: :laugh: :laugh:
Now where's that image of Banshee.... Hmmm.... :laugh:
Now where's that image of Banshee.... Hmmm.... :laugh:
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
Please Log in or Create an account to join the conversation.
- 531blackbanshee
-
- Offline
- Vendor
-

Vendors
- Posts: 7442
- Thanks: 796
Re: cam end caps
01 Oct 2009 09:56
hmmmmmmmm,certain things should never make it to the net!haha,sorry omr.you are kinda like my z1r,alot of fun to play with.hehe,
leon holmes
leon holmes
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
Please Log in or Create an account to join the conversation.
- Kapahulu
-
- Offline
- User
-

Registered
- Posts: 564
- Thanks: 41
Re: cam end caps
11 Jan 2012 01:56
I'm going through the leaky cap issue now with my 1978 KZ1000. When I bought it, the left front side cap (nearest cylinder #1 exhaust) was leaking. I bought new rubber caps, installed them using permatex and that same one still leaked.
Next, I tried the plumber's tape and sealant method mentioned earlier in this thread. That didn't go well. The cap blew out when I was on the highway and my left leg was bathed in oil.
So I ordered the aluminum caps from Z1 Enterprises. They come with a viton rubber strip. There were no installation instructions so I didn't use any sealant. Fired it up and that same side cap started leaking big time. I thought the viton rubber would seal it up - I guess not.
I picked up some three bond. Tomorrow I'll take the cover off again, remove that cap, clean up the surface on the head and use three bond, the viton, let it sit overnight and then start it and see if it leaks.
Anyone have a suggestion to add to this plan?
Next, I tried the plumber's tape and sealant method mentioned earlier in this thread. That didn't go well. The cap blew out when I was on the highway and my left leg was bathed in oil.
So I ordered the aluminum caps from Z1 Enterprises. They come with a viton rubber strip. There were no installation instructions so I didn't use any sealant. Fired it up and that same side cap started leaking big time. I thought the viton rubber would seal it up - I guess not.
I picked up some three bond. Tomorrow I'll take the cover off again, remove that cap, clean up the surface on the head and use three bond, the viton, let it sit overnight and then start it and see if it leaks.
Anyone have a suggestion to add to this plan?
1978 KZ1000, 1976 KZ900, 1975 H2, 1973 H1, 1973 H2, 1978 RD400, 1977 RD400, 1974 RD350
2strokeworld.com
2strokeworld.com
Please Log in or Create an account to join the conversation.
- jonnybravo
-
- Offline
- Banned
-

Registered
- Posts: 518
- Thanks: 18
Re: cam end caps
11 Jan 2012 02:07
Z1 1 Ent also has the aluminum caps, thats where i got mine, didnt particularly want blue myself
Please Log in or Create an account to join the conversation.
- Kapahulu
-
- Offline
- User
-

Registered
- Posts: 564
- Thanks: 41
Re: cam end caps
11 Jan 2012 02:12
That's what I'm using now, for the same reason. Still have to solve the leak problem.
1978 KZ1000, 1976 KZ900, 1975 H2, 1973 H1, 1973 H2, 1978 RD400, 1977 RD400, 1974 RD350
2strokeworld.com
2strokeworld.com
Please Log in or Create an account to join the conversation.
- jonnybravo
-
- Offline
- Banned
-

Registered
- Posts: 518
- Thanks: 18
Re: cam end caps
11 Jan 2012 02:30
because of the head i had to file two of the end caps down a little to get the valve cover to fit correctly, then i put the O ring material in the groove, I also used a sealer, 3 Bond is my personal choice but others will work
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
