Piston Gas Porting

  • kzz1p
  • kzz1p's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • One Test Is Worth A Thousand Expert Opinions!
  • Posts: 1432
  • Thanks: 3

Re: Piston Gas Porting

24 Oct 2009 13:15
#329365
Patton wrote:
kzz1p wrote:

:unsure: Seems like the holes would tend to get plugged with carbon after running for a little while longer than 1/4 mile :unsure:

Good Luck! :)

A 1/4 mile bike doesn't get as much carbon, as a street bike. But yes! They can get clogged over time.

Please Log in or Create an account to join the conversation.

  • APE Jay
  • APE Jay's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Piston Gas Porting

24 Oct 2009 21:54
#329447
kzz1p wrote:
APE Jay wrote:
We usually do 8



Jay

Does the wear rate of the rings increase?

We usually only do dragbikes and have not seen any drastic wear.

It is interesting that the new German Wossner turbo pistons are coming from the factory with gas porting.

Interesting tid bit. Radial gas porting, which is harder to do, was originally done as a "cheating" method in stock cars where gas porting was not legal. With radial gas porting, you can not tell if the piston is in the cylinder.

Please Log in or Create an account to join the conversation.

  • kzz1p
  • kzz1p's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • One Test Is Worth A Thousand Expert Opinions!
  • Posts: 1432
  • Thanks: 3

Re: Piston Gas Porting

24 Oct 2009 22:14
#329449
APE Jay wrote:
kzz1p wrote:
APE Jay wrote:
We usually do 8



Jay

Does the wear rate of the rings increase?

We usually only do dragbikes and have not seen any drastic wear.

It is interesting that the new German Wossner turbo pistons are coming from the factory with gas porting.

Interesting tid bit. Radial gas porting, which is harder to do, was originally done as a "cheating" method in stock cars where gas porting was not legal. With radial gas porting, you can not tell if the piston is in the cylinder.

Jay
Thanks for your answer!

Please Log in or Create an account to join the conversation.

  • ArthurGoVroom
  • ArthurGoVroom's Avatar
  • Offline
  • User
  • User
    Registered
  • I'd rather ride it than shine it
  • Posts: 52
  • Thanks: 0

Re: Piston Gas Porting

25 Oct 2009 10:42
#329506
kzz1p wrote:
Was your 10% gain, in the upper RPM range?

Yes. The gain was more pronounced at and above the peak HP point. I attribute at least some of this to the lower mass piston though. I agree with the general consensus here that gasporting helps more in the higher compression/boost applications.

As for clogging up the gasports...If you run them on alcohol you don't have that problem :)
1976 KZ900A4, 4-1 header, rear lowering kit, grab bar removed, still shining and painting parts as time permits

Please Log in or Create an account to join the conversation.

  • PLUMMEN
  • PLUMMEN's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7983
  • Thanks: 104

Re: Piston Gas Porting

25 Oct 2009 11:03
#329514
APE Jay wrote:
kzz1p wrote:
APE Jay wrote:
We usually do 8



Jay

Does the wear rate of the rings increase?

We usually only do dragbikes and have not seen any drastic wear.

It is interesting that the new German Wossner turbo pistons are coming from the factory with gas porting.

Interesting tid bit. Radial gas porting, which is harder to do, was originally done as a "cheating" method in stock cars where gas porting was not legal. With radial gas porting, you can not tell if the piston is in the cylinder.
cheating in racing? :laugh: say it isnt so,thats why i tend to follow the old saying of run what ya brung and hope its enough! :woohoo:
Still recovering,some days are better than others.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum