zx cam dilemma
- jimmybon
-
Topic Author
- Offline
- User
-

Registered
- Posts: 209
- Thanks: 2
zx cam dilemma
07 Dec 2009 12:54
I'v just purchased a set of GPZ750ZX cams from a wrecker/breaker to replace GPZ750R1 82 cams and was looking for any members who may have a set on hand
I'v measured the inlet cam lob height .5mm bigger then the R1 @36.8mm, but its the EX cam thats my dilemma.
It measures .5mm smaller @35.8mm and the lob base dia is also smaller by .9mm @27.3mm. It also measures up to have a more steeper angle ( fatter at the lobe angle ) but I thought that both cams, IN & EX have .5mm more lift
I'd much appreciate some help with this before I install and shim up
I'v measured the inlet cam lob height .5mm bigger then the R1 @36.8mm, but its the EX cam thats my dilemma.
It measures .5mm smaller @35.8mm and the lob base dia is also smaller by .9mm @27.3mm. It also measures up to have a more steeper angle ( fatter at the lobe angle ) but I thought that both cams, IN & EX have .5mm more lift
I'd much appreciate some help with this before I install and shim up
74 Z1A900 original
74 Z1A900 stone replica
74Z1A900 barn find
77 Z650B1 Hybrid
81 z650 PIG camp bike
06 ZRX1200R cafe racer project
S1000xr
74 Z1A900 stone replica
74Z1A900 barn find
77 Z650B1 Hybrid
81 z650 PIG camp bike
06 ZRX1200R cafe racer project
S1000xr
Please Log in or Create an account to join the conversation.
- otakar
-
- Offline
- User
-

Registered
- Posts: 5069
- Thanks: 29
Re: zx cam dilemma
07 Dec 2009 13:30
The lift is the difference between the height and the base circle diameter. You may have a hard time finding shims thick enough to make up the difference. If you recess the valve to make up that difference you will loose compression. I would stay wit your original exhaust cam and just change the intake. this will give you a longer power stroke. I did that on my GPz1100. My exhaust is .010 less lift than my Intake. This gives better low end torque.
74 Z1-A stock
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000
Please Log in or Create an account to join the conversation.
- jimmybon
-
Topic Author
- Offline
- User
-

Registered
- Posts: 209
- Thanks: 2
Re: zx cam dilemma
07 Dec 2009 13:50
Thanks mate,I'll definatly look at that
The question is - is the EX cam I purchased a gpz750ZX cam
The question is - is the EX cam I purchased a gpz750ZX cam
74 Z1A900 original
74 Z1A900 stone replica
74Z1A900 barn find
77 Z650B1 Hybrid
81 z650 PIG camp bike
06 ZRX1200R cafe racer project
S1000xr
74 Z1A900 stone replica
74Z1A900 barn find
77 Z650B1 Hybrid
81 z650 PIG camp bike
06 ZRX1200R cafe racer project
S1000xr
Please Log in or Create an account to join the conversation.
- Nebr_Rex
-
- Offline
- User
-

Registered
- Posts: 1889
- Thanks: 295
Re: zx cam dilemma
07 Dec 2009 14:29
jimmybon wrote:
yes it is,the late GPZ750 has a smaller base circle on the exhaust
still more total lift and duration
Thanks mate,I'll definatly look at that
The question is - is the EX cam I purchased a gpz750ZX cam
yes it is,the late GPZ750 has a smaller base circle on the exhaust
still more total lift and duration
2002 ZRX1200R
81 GPz1100
79 KZ1000st daily ride
79 KZ1000mk2 prodject
78 KZ650sr
78 KZ650b
81 KZ750e
80 KZ750ltd
77 KZ400/440 cafe project
76 KZ400/440 Fuel Injected
www.dotheton.com/index.php?threads/dr-je...air-of-kz400s.39120/
.
81 GPz1100
79 KZ1000st daily ride
79 KZ1000mk2 prodject
78 KZ650sr
78 KZ650b
81 KZ750e
80 KZ750ltd
77 KZ400/440 cafe project
76 KZ400/440 Fuel Injected
www.dotheton.com/index.php?threads/dr-je...air-of-kz400s.39120/
.
Please Log in or Create an account to join the conversation.
- jimmybon
-
Topic Author
- Offline
- User
-

Registered
- Posts: 209
- Thanks: 2
Re: zx cam dilemma
07 Dec 2009 15:05
cheers for that,
my calc on the lobe height is 35.8mm and the base dia 27.3, so base dia 27.3 / 2 = 13.65, then 35.8 - 13.65 = 22.15 lift from the cam centre line to the lobe
Using the same calc on the R1 and ZR7 cams, the figer is 22.2, going by this the lift is marginly smaller but definatly more duration
my calc on the lobe height is 35.8mm and the base dia 27.3, so base dia 27.3 / 2 = 13.65, then 35.8 - 13.65 = 22.15 lift from the cam centre line to the lobe
Using the same calc on the R1 and ZR7 cams, the figer is 22.2, going by this the lift is marginly smaller but definatly more duration
74 Z1A900 original
74 Z1A900 stone replica
74Z1A900 barn find
77 Z650B1 Hybrid
81 z650 PIG camp bike
06 ZRX1200R cafe racer project
S1000xr
74 Z1A900 stone replica
74Z1A900 barn find
77 Z650B1 Hybrid
81 z650 PIG camp bike
06 ZRX1200R cafe racer project
S1000xr
Please Log in or Create an account to join the conversation.
- jimmybon
-
Topic Author
- Offline
- User
-

Registered
- Posts: 209
- Thanks: 2
Re: zx cam dilemma
07 Dec 2009 18:19
OK, I think I get it
the .5mm shorter at the bottom of the base dia is taken up by shims and the lobe acts on the valve earlyer giving extra .5mm lift
the .5mm shorter at the bottom of the base dia is taken up by shims and the lobe acts on the valve earlyer giving extra .5mm lift
74 Z1A900 original
74 Z1A900 stone replica
74Z1A900 barn find
77 Z650B1 Hybrid
81 z650 PIG camp bike
06 ZRX1200R cafe racer project
S1000xr
74 Z1A900 stone replica
74Z1A900 barn find
77 Z650B1 Hybrid
81 z650 PIG camp bike
06 ZRX1200R cafe racer project
S1000xr
Please Log in or Create an account to join the conversation.
- jimmybon
-
Topic Author
- Offline
- User
-

Registered
- Posts: 209
- Thanks: 2
Re: zx cam dilemma
07 Dec 2009 18:26
74 Z1A900 original
74 Z1A900 stone replica
74Z1A900 barn find
77 Z650B1 Hybrid
81 z650 PIG camp bike
06 ZRX1200R cafe racer project
S1000xr
74 Z1A900 stone replica
74Z1A900 barn find
77 Z650B1 Hybrid
81 z650 PIG camp bike
06 ZRX1200R cafe racer project
S1000xr
Please Log in or Create an account to join the conversation.
- cafekz750
-
- Offline
- User
-

Registered
- Posts: 333
- Thanks: 0
Re: zx cam dilemma
08 Dec 2009 06:44 - 08 Dec 2009 06:58
I bought a set of 1983 GPZ750 cams for my KZ and found the same thing. That the exhaust side was going to need a thicker shim to make up the additional clearance provided by the smaller base circle. I have attached a picture that I pieced together from the FSM for the KZ. Take a look at the "Cam Height" and the "Valve Installed Height".
1983 KZ/GPZ Cam Specifications
1983 KZ/GPZ Cam Specifications
1981 KZ750H2 - V&H 4-1 pipe, pods, jetted, clubmans, homebrew rearsets, 18" rear wheel and more.
Parting out a 1982 KZ750H3 to fund future projects
2 other non-Kawasaki motorcycles
Parting out a 1982 KZ750H3 to fund future projects
2 other non-Kawasaki motorcycles
Last edit: 08 Dec 2009 06:58 by cafekz750.
Please Log in or Create an account to join the conversation.
- jimmybon
-
Topic Author
- Offline
- User
-

Registered
- Posts: 209
- Thanks: 2
Re: zx cam dilemma
08 Dec 2009 12:26
Cool, I'll keep a copy of that
cheers
cheers
74 Z1A900 original
74 Z1A900 stone replica
74Z1A900 barn find
77 Z650B1 Hybrid
81 z650 PIG camp bike
06 ZRX1200R cafe racer project
S1000xr
74 Z1A900 stone replica
74Z1A900 barn find
77 Z650B1 Hybrid
81 z650 PIG camp bike
06 ZRX1200R cafe racer project
S1000xr
Please Log in or Create an account to join the conversation.
- FKK
-
- Offline
- User
-

Registered
- Posts: 7
- Thanks: 0
Re: zx cam dilemma
07 Nov 2011 17:07
Hello, I'm Felix from Holland.
I have the exact same situation with smaller base circle ZX cam in a KZ head.
My question, will it run (well) with the original KZ exhaust cam and the ZX inlet cam?
Will I make full use of the more powerful inlet cam when I maintain the old exhaust cam? Or do I really need the ZX exhaust cam as well.
I understand the lift is effectively the same but the duration would be different, and what would that lead to?
Thanks
Felix
I have the exact same situation with smaller base circle ZX cam in a KZ head.
My question, will it run (well) with the original KZ exhaust cam and the ZX inlet cam?
Will I make full use of the more powerful inlet cam when I maintain the old exhaust cam? Or do I really need the ZX exhaust cam as well.
I understand the lift is effectively the same but the duration would be different, and what would that lead to?
Thanks
Felix
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
