After 7 years its alive!, mostly..
- KLD
-
Topic Author
- Offline
- User
-

Registered
- Posts: 52
- Thanks: 0
After 7 years its alive!, mostly..
18 Feb 2010 22:21 - 18 Feb 2010 22:24
Well the 73 z1 started and worked like a beast, even on 3 cylinder. After about 10 kicks she started popping after dicking with the controls. Then after a few more kicks she started right up. It was running, but not on the 1st cylinder. I could tell because the pipe on the first cylinder was cold. Even after it warmed up, it wouldn't run without the choke being on, im thinking thats because its only running on 3 cylinders, but could be wrong. I'm also thinking it might be a carb issue because the carb on the 1st cylinder was pretty bad.. It had tons of buildup, whereas the rest wern't too bad. I thought I did a proper job on the carbs, spent a long while cleaning them. Any ideas what the problem could be?
Heres some pictures
Thats what the first sparkplug looked like after running it for about 5 minutes with full choke. The rest of the spark plugs looked the same as the second one
Heres some pictures
Thats what the first sparkplug looked like after running it for about 5 minutes with full choke. The rest of the spark plugs looked the same as the second one
Last edit: 18 Feb 2010 22:24 by KLD.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: After 7 years its alive!, mostly..
19 Feb 2010 02:55 - 19 Feb 2010 03:05
#1 cylinder ---
If not already done, would attach brand new NGKB8ES spark plug to plug wire, ground plug base to engine head, spin engine over and visually inspect spark quality at tip of plug.
If spark looks okay, install the brand new NGKB8ES spark plug and again test run engine.
If #1 cylinder still fails to combust, would perform compression test on #1 cylinder. AND assure both valve clearances are to specs in #1 cylinder. A too tight valve could easily cause the reported problem (even where cold compression test seems okay).
When satisfied that both spark and compression and valve clearances are okay in #1 cylinder, would then perform clear tube test to assure fuel level in float bowl isn't too high and causing a too rich condition in #1 carb.
Given good properly timed spark with decent compression and correct valve clearances, and prescribed fuel level, if combustion still fails in #1 cylinder, the problem is probably carb related. Most likely an issue with the pilot circuit (or maybe the enrichener circuit) in #1 carb.
Pilot circuit passages, both air passage and fuel passage and air-fuel passages, are sometimes very difficult to clean. And sometimes the pilot jet is so dirty or damaged that it should be replaced with a new pilot jet of the same size.
Would also assure intake air filter isn't over-oiled or otherwise blocked. Some pod models may partially obstruct the pilot air intake hole. Could remove the pod on #1 carb for test run.
Good Luck!
If not already done, would attach brand new NGKB8ES spark plug to plug wire, ground plug base to engine head, spin engine over and visually inspect spark quality at tip of plug.
If spark looks okay, install the brand new NGKB8ES spark plug and again test run engine.
If #1 cylinder still fails to combust, would perform compression test on #1 cylinder. AND assure both valve clearances are to specs in #1 cylinder. A too tight valve could easily cause the reported problem (even where cold compression test seems okay).
When satisfied that both spark and compression and valve clearances are okay in #1 cylinder, would then perform clear tube test to assure fuel level in float bowl isn't too high and causing a too rich condition in #1 carb.
Given good properly timed spark with decent compression and correct valve clearances, and prescribed fuel level, if combustion still fails in #1 cylinder, the problem is probably carb related. Most likely an issue with the pilot circuit (or maybe the enrichener circuit) in #1 carb.
Pilot circuit passages, both air passage and fuel passage and air-fuel passages, are sometimes very difficult to clean. And sometimes the pilot jet is so dirty or damaged that it should be replaced with a new pilot jet of the same size.
Would also assure intake air filter isn't over-oiled or otherwise blocked. Some pod models may partially obstruct the pilot air intake hole. Could remove the pod on #1 carb for test run.
Good Luck!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 19 Feb 2010 03:05 by Patton.
Please Log in or Create an account to join the conversation.
- Kawickrice
-
- Offline
- User
-

Registered
- After Monday & Tuesday, even the calendar says WTF
- Posts: 2469
- Thanks: 20
Re: After 7 years its alive!, mostly..
19 Feb 2010 07:07
Pull the carbs and go through them again. The number one cylinder will catch all the garbage from the tank most times. When it leans on the sidestand it makes since that number one will usually be in worse condition. It took me a few times of pulling the carbs to get my issue worked out. On mine one and two carbs were in rough shape.
73 Kawasaki Z1
07 HD CVO Ultra Classic
82 Suzuki GS 1100
74 Yamaha RD 350 (My two stroke toy)
77 Kawasaki KZ 650B-1 (My putt around bike)
80 Indian Moped (My American Iron)
1
Long Gone
75 Suzuki GT550
74 GT 380
79 RD 400 Daytona Special
72 Honda CL 175
74 Honda QA 50
Tampa FL
07 HD CVO Ultra Classic
82 Suzuki GS 1100
74 Yamaha RD 350 (My two stroke toy)
77 Kawasaki KZ 650B-1 (My putt around bike)
80 Indian Moped (My American Iron)
1
Long Gone
75 Suzuki GT550
74 GT 380
79 RD 400 Daytona Special
72 Honda CL 175
74 Honda QA 50
Tampa FL
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: After 7 years its alive!, mostly..
19 Feb 2010 07:24
Everything Patton said...
I may just cut n' paste this to several other locations! :laugh: :laugh: :laugh:
I may just cut n' paste this to several other locations! :laugh: :laugh: :laugh:
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
- 531blackbanshee
-
- Offline
- Vendor
-

Vendors
- Posts: 7442
- Thanks: 796
Re: After 7 years its alive!, mostly..
19 Feb 2010 09:39 - 19 Feb 2010 09:41
patton had good info.
does the #1 plug have gas on it?
leon
does the #1 plug have gas on it?
leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
Last edit: 19 Feb 2010 09:41 by 531blackbanshee.
Please Log in or Create an account to join the conversation.
- KLD
-
Topic Author
- Offline
- User
-

Registered
- Posts: 52
- Thanks: 0
Please Log in or Create an account to join the conversation.
- z650c3
-
- Offline
- User
-

Registered
- Posts: 78
- Thanks: 0
Re: After 7 years its alive!, mostly..
19 Feb 2010 14:11
KLD wrote:
Sounds like almost certain to be a carb problem Best of luck gettin it sorted.
Cheers
c3
No, It did not smell of gas at all
Sounds like almost certain to be a carb problem Best of luck gettin it sorted.
Cheers
c3
1979 z650 c3 first registered in 1981
2006 Harley Davidson VRSCR
Northern Ireland
2006 Harley Davidson VRSCR
Northern Ireland
Please Log in or Create an account to join the conversation.
- KLD
-
Topic Author
- Offline
- User
-

Registered
- Posts: 52
- Thanks: 0
Re: After 7 years its alive!, mostly..
19 Feb 2010 15:05 - 19 Feb 2010 15:06
I pulled the carbs off and the float level was too low, so I readjusted it.
Did a quick compression test and it was good. It has good spark. It doesn't have any type of filter on at the moment to restrict air flow. Valve clearances are up to spec. The jets are clean as a whistle. So.. that leaves the fuel passages.. i suppose
Did a quick compression test and it was good. It has good spark. It doesn't have any type of filter on at the moment to restrict air flow. Valve clearances are up to spec. The jets are clean as a whistle. So.. that leaves the fuel passages.. i suppose
Last edit: 19 Feb 2010 15:06 by KLD.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: After 7 years its alive!, mostly..
19 Feb 2010 15:17
Even on just three cylinders, should perform surprisingly well, and run with (or out-perform) most Harleys, and full turnpike cruising speeds being easily sustainable.
[Click on image to enlarge view.]
Good Luck!
[Click on image to enlarge view.]
Good Luck!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- KLD
-
Topic Author
- Offline
- User
-

Registered
- Posts: 52
- Thanks: 0
Re: After 7 years its alive!, mostly..
19 Feb 2010 19:06
Thats going to be very helpful, Thanks a bunch! I'll keep you all posted
Please Log in or Create an account to join the conversation.
- Old Man Rock
-
- Offline
- User
-

Registered
- Posts: 6071
- Thanks: 225
Re: After 7 years its alive!, mostly..
20 Feb 2010 08:37
Have you tried swapping plug wires 1 & 4?
See if the problem follows to #4 then it's electrical and not carbies....
Just a thought before having to tear apart the carbs...
OMR
See if the problem follows to #4 then it's electrical and not carbies....
Just a thought before having to tear apart the carbs...
OMR
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: After 7 years its alive!, mostly..
20 Feb 2010 09:48 - 20 Feb 2010 09:53
KLD wrote:
Would more likely suspect a too high fuel level causing the black sooty plug from an over rich mixture.
Am hoping the clear tube test was performed.
When performing the clear tube test to determine float bowl fuel level, pulling the carbs isn't necessary. Because the clear tube test may be performed with the carbs remaining installed on fully assembled bike, without carb removal or disassembly. Bike should be held level and stationary during the test.
The clear tube test tells the true actual existing fuel level, regardless of float buoyancy and other variables.
Imo, the carb-disassembled-upside-down-on-workbench method (measuring physical distances involved) is a ball park adjustment to be confirmed with the clear tube test.
The clear tube test may also be performed with the assembled carbs on the workbench. Where the carbs must remain level during the test.
Too high fuel level in otherwise perfect carbs, and perfect everything else, will cause over rich mixture evidenced by black sooty plugs.
Good Luck!
I pulled the carbs off and the float level was too low, so I readjusted it....
Would more likely suspect a too high fuel level causing the black sooty plug from an over rich mixture.
Am hoping the clear tube test was performed.
When performing the clear tube test to determine float bowl fuel level, pulling the carbs isn't necessary. Because the clear tube test may be performed with the carbs remaining installed on fully assembled bike, without carb removal or disassembly. Bike should be held level and stationary during the test.
The clear tube test tells the true actual existing fuel level, regardless of float buoyancy and other variables.
Imo, the carb-disassembled-upside-down-on-workbench method (measuring physical distances involved) is a ball park adjustment to be confirmed with the clear tube test.
The clear tube test may also be performed with the assembled carbs on the workbench. Where the carbs must remain level during the test.
Too high fuel level in otherwise perfect carbs, and perfect everything else, will cause over rich mixture evidenced by black sooty plugs.
Good Luck!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 20 Feb 2010 09:53 by Patton.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
