79 kz650 Engine Start Problem
- BoomerX
-
Topic Author
- Offline
- User
-

Registered
- Posts: 17
- Thanks: 0
Re: 79 kz650 Engine Start Problem
09 Mar 2010 16:41 - 09 Mar 2010 16:42
The point gaps were so out of wack.
After gapping points and double checking wires, fired up and ran very strong.
After gapping points and double checking wires, fired up and ran very strong.
79' KZ650
Last edit: 09 Mar 2010 16:42 by BoomerX.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: 79 kz650 Engine Start Problem
09 Mar 2010 17:10 - 09 Mar 2010 17:12
BoomerX wrote:
As likely already known, when dealing with points, the sequential steps are:
1. Clean (and file if necessary) the contacts;
2. Set the gap (because the gap influences setting of the timing);
3. Set the timing.
This preferred sequence is mentioned so somebody won't ill-advisedly set the gap after setting the timing.
In other words, if timing is spot on, and then gap is re-set, timing will likely be adversely effected and require re-setting to again be spot on.
Good Fortune!
The point gaps were so out of wack.
After gapping points and double checking wires, fired up and ran very strong.
As likely already known, when dealing with points, the sequential steps are:
1. Clean (and file if necessary) the contacts;
2. Set the gap (because the gap influences setting of the timing);
3. Set the timing.
This preferred sequence is mentioned so somebody won't ill-advisedly set the gap after setting the timing.
In other words, if timing is spot on, and then gap is re-set, timing will likely be adversely effected and require re-setting to again be spot on.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 09 Mar 2010 17:12 by Patton.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: 79 kz650 Engine Start Problem
09 Mar 2010 17:16 - 09 Mar 2010 17:21
A drop of oil on the felt pad helps keep the heels from wearing out as quickly from rubbing against the spinning cam. The cam isn't shown in this photo from KZ900.
Good Fortune!
[Click on image to enhance view.]
Good Fortune!
[Click on image to enhance view.]
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 09 Mar 2010 17:21 by Patton.
Please Log in or Create an account to join the conversation.
- fjf
-
- Offline
- User
-

Registered
- Posts: 3
- Thanks: 0
Re: 79 kz650 Engine Start Problem
26 May 2011 08:14
Mine (KZ650 B2) also backfires thru carbs and vacuum line - from carb#2 - blows and sucks alternately :silly:
Problem seems to be the cam chain is not properly sync with valve sprockets as tensor failed...
The bad news are that one plastic piece falled down within the engine and I cannot take it out...
Problem seems to be the cam chain is not properly sync with valve sprockets as tensor failed...
The bad news are that one plastic piece falled down within the engine and I cannot take it out...
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: 79 kz650 Engine Start Problem
26 May 2011 09:06fjf wrote: Mine (KZ650 B2) also backfires thru carbs and vacuum line - from carb#2 - blows and sucks alternately :silly:
Problem seems to be the cam chain is not properly sync with valve sprockets as tensor failed...
The bad news are that one plastic piece falled down within the engine and I cannot take it out...
Failure of intake valve to seal when closed may result in backfire through carb.
Would check valve clearances (especially intakes) and do compression test to verify valves are fully sealing when closed.
The plastic piece may be lying harmlessly on floor of the pan.
It might flush out when draining the oil.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- fjf
-
- Offline
- User
-

Registered
- Posts: 3
- Thanks: 0
Re: 79 kz650 Engine Start Problem
26 May 2011 20:12 - 30 May 2011 08:13
Thank you for your comments. Finally I decided to open the engine and found one cam drive tensor sproke broken; sync was therefore impossible. I have rebuilt IT and will see wether the issue is resolved.
Thanks for your help again
Fotos: the broken sprocket (two rubber silent-blocks are missed), the internal rubber is re-built with Nural-21 and two external rubber flat-rings glued.
Thanks for your help again
Fotos: the broken sprocket (two rubber silent-blocks are missed), the internal rubber is re-built with Nural-21 and two external rubber flat-rings glued.
Last edit: 30 May 2011 08:13 by fjf.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
