New cams
- customkz1000
-
Topic Author
- Offline
- User
-

Registered
- Posts: 31
- Thanks: 0
New cams
24 Apr 2010 07:01 - 24 Apr 2010 07:06
I'm rebuilding my Kz 1000 and I need to know how many horses I can get by putting 2x cams in and having the head shaved
Last edit: 24 Apr 2010 07:06 by customkz1000.
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: New cams
24 Apr 2010 07:30 - 24 Apr 2010 07:31
u will have to be very careful with this task Luke.
Go not, where u have no knowledge.
if u mill the head the valves will get closer to the piston.
if u use larger cams to valves will get closer to the pistons, and valve to valve.
High compression pistons have the valve pockets pre cut to allow for these things, but u must always measure.
u should maintain a min clearance of .080" int., .060" ext. from piston to valve.
new pistons are the better path Luke. u will gain cc's as well.
No point putting a lot of money into upgrades without improving the breathing. Porting allows it to breath better.
Contact Larry Cavanaugh for support hear.
www.flowbenchtech.com/porting/CRH/index.htm
Go not, where u have no knowledge.
if u mill the head the valves will get closer to the piston.
if u use larger cams to valves will get closer to the pistons, and valve to valve.
High compression pistons have the valve pockets pre cut to allow for these things, but u must always measure.
u should maintain a min clearance of .080" int., .060" ext. from piston to valve.
new pistons are the better path Luke. u will gain cc's as well.
No point putting a lot of money into upgrades without improving the breathing. Porting allows it to breath better.
Contact Larry Cavanaugh for support hear.
www.flowbenchtech.com/porting/CRH/index.htm
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Last edit: 24 Apr 2010 07:31 by mark1122.
Please Log in or Create an account to join the conversation.
- larrycavan
-
- User
-

Public
- Thanks: 0
Re: New cams
24 Apr 2010 15:36
customkz1000 wrote:
Mill the head just enough to make it flat and no more. Those cams will make a noticable difference for you. Tune it right and you could pick up 8-10 Peak HP.
You can put them right in on stock srockets and they'll work just fine. You'l get more peak torque if you pull them to 106 centers but if you're not experienced at degreeing the cams, then just bolt them in with stock sprockets.
Grind the X's out of the valve cover to be safe. It's just good practice to get them out of there.
I'm rebuilding my Kz 1000 and I need to know how many horses I can get by putting 2x cams in and having the head shaved
Mill the head just enough to make it flat and no more. Those cams will make a noticable difference for you. Tune it right and you could pick up 8-10 Peak HP.
You can put them right in on stock srockets and they'll work just fine. You'l get more peak torque if you pull them to 106 centers but if you're not experienced at degreeing the cams, then just bolt them in with stock sprockets.
Grind the X's out of the valve cover to be safe. It's just good practice to get them out of there.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
