Porting a KZ750 (4)

  • chrispysaki
  • chrispysaki's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 150
  • Thanks: 0

Porting a KZ750 (4)

06 May 2010 14:07
#365972
I'm thinking about doing some mild porting to my intakes and exhausts and I know I should really have it done professionally with a flow bench and other equipment, but are there any safe guidelines for doing some basic, mild porting without making it worse?

And are the gains even sufficient with a mild porting job to be worth the trouble?

Right now I'm running it with pods, 4-1 and gpz cams.

Thanks,
Chris

Please Log in or Create an account to join the conversation.

  • otakar
  • otakar's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 5069
  • Thanks: 29

Re: Porting a KZ750 (4)

06 May 2010 15:59
#365989
If you remove the roughness in the casting and match the boots to the ports it will make a difference.
74 Z1-A stock
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000

Please Log in or Create an account to join the conversation.

  • hocbj23
  • hocbj23's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Porting a KZ750 (4)

06 May 2010 16:47
#366009
As otakar said,try to match ur gaskets and port sizes as much as u can.U can do it with a Dremel and LOTS of sanding/polishing drums.Try to control the aluminum dust as this is a dirty job and u dont want that stuff in ur lungs.wear a painters mask. Remember the venturi effect. On the intake side, try to taper the ports slightly so the side facing the carbs is larger than the side facing the valves.. On the ehhaust side, the reverse is true.The taper should be larger close to the valves and smaller where the exhaust bolts on.Get the air/fuel mix in quick and the burnt gases out quick.Use a carb boot and marking pencil to outline what material u need to remove on the intke side and use a crush washer/marker for the exhaust side.hope this helps.bj

Please Log in or Create an account to join the conversation.

  • T_Dub
  • T_Dub's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1441
  • Thanks: 26

Re: Porting a KZ750 (4)

06 May 2010 17:57
#366029
The venturi effect only speeds up the fluid locally in the constriction, it doesn't speed up the flow overall, the conservation laws prohibit that.

Basically what you need to do is reduce resistance to flow, and making your ports smoother will do this. Also, some improper porting can cause big velocity differentials across a cross section, leading to poorer flow than you started with.
1977 KZ650B1
-810cc
-Cavanaugh Racing Head
-Mikuni RS34's
-GPR Muffler

Please Log in or Create an account to join the conversation.

  • larrycavan
  • larrycavan's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Porting a KZ750 (4)

06 May 2010 17:59
#366030
chrispysaki wrote:
I'm thinking about doing some mild porting to my intakes and exhausts and I know I should really have it done professionally with a flow bench and other equipment, but are there any safe guidelines for doing some basic, mild porting without making it worse?

And are the gains even sufficient with a mild porting job to be worth the trouble?

Right now I'm running it with pods, 4-1 and gpz cams.

Thanks,
Chris

Chris,

Decarbon the combustion chambers and inspect the intake valve seats to see if they're chipping away. I've seen several like that in the past year.

They chip away from the outside edge, just outside the 45 cut. Do this before you attempt to port the head. No use in putting hours into a head that needs the seats replaced.

Please Log in or Create an account to join the conversation.

  • chrispysaki
  • chrispysaki's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 150
  • Thanks: 0

Re: Porting a KZ750 (4)

07 May 2010 07:30
#366158
Thanks for the tips everyone. I'll keep an eye out for chips in the valve seats.

Please Log in or Create an account to join the conversation.

  • Ituen
  • Ituen's Avatar
  • Offline
  • User
  • User
    Registered
  • Rider
  • Posts: 143
  • Thanks: 1

Re: Porting a KZ750 (4)

07 May 2010 16:28
#366273
Send your head to a professional like larrycavan. He's the best! (I just sent him one of my heads).
1982 KZ750 E
Kawasaki Rider

Please Log in or Create an account to join the conversation.

  • larrycavan
  • larrycavan's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Porting a KZ750 (4)

07 May 2010 19:54
#366329
DO NOT match the exhaust port exit to the gasket. You want a step there to fight reversion. :)

Please Log in or Create an account to join the conversation.

  • T_Dub
  • T_Dub's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1441
  • Thanks: 26

Re: Porting a KZ750 (4)

07 May 2010 20:38
#366342
And listen to Mr. C. You can't do anything better than to listen to him.
1977 KZ650B1
-810cc
-Cavanaugh Racing Head
-Mikuni RS34's
-GPR Muffler

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum