high compression
- rspector
-
Topic Author
- Offline
- User
-

Registered
- Posts: 22
- Thanks: 0
high compression
15 May 2010 19:09
I have a kz1000 bored to 1327, i'm curious to why i keep blowing starter clutchs, I've replaced a number of them in my life and am wondering if the engine mods require something a little more heavy duty then stock. If so can any one suggest a place for me to look?
Thanks
Thanks
Please Log in or Create an account to join the conversation.
- PLUMMEN
-
- Offline
- User
-

Registered
- Posts: 7983
- Thanks: 104
Re: high compression
15 May 2010 19:21
whats in the motor?
Still recovering,some days are better than others.
Please Log in or Create an account to join the conversation.
- porchev914
-
- Offline
- User
-

Registered
- Whats that? Half of my swingarm is missing?!?!?
- Posts: 2708
- Thanks: 19
Re: high compression
15 May 2010 20:02
And what's your cranking compression?
FRANKEN Z!
1978 KZ1000 A2A with 08'Speed Triple SSSA and '06 GSXR1000 front end
1978 KZ1000 A2A with 08'Speed Triple SSSA and '06 GSXR1000 front end
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: high compression
16 May 2010 07:59
Yes.
Not sure where to look :huh:
Not sure where to look :huh:
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
- Old Man Rock
-
- Offline
- User
-

Registered
- Posts: 6071
- Thanks: 225
Re: high compression
16 May 2010 08:41
Several questions come to mind....
1) blowing starter clutchs:
Blowing meaning?... i.e. clutch gear itself breaking teeth, snapping in half etc....
Does "Blowing" occur after a certain time lapse indicating slow degradations or all is good then WHAM, gear busts...
2) Electric start, kick start or external starter?
3) Have you also been replacing the Needle bearings, rollers and Springs?
4) abnormal noises when starting or during normal engine running?
5) Possibly damper rubber clearances are off.
Best guess at this point, weak springs/roller travel free play...
This is out of my KZ900 Shop manual, maybe will help....
OMR
1) blowing starter clutchs:
Blowing meaning?... i.e. clutch gear itself breaking teeth, snapping in half etc....
Does "Blowing" occur after a certain time lapse indicating slow degradations or all is good then WHAM, gear busts...
2) Electric start, kick start or external starter?
3) Have you also been replacing the Needle bearings, rollers and Springs?
4) abnormal noises when starting or during normal engine running?
5) Possibly damper rubber clearances are off.
Best guess at this point, weak springs/roller travel free play...
This is out of my KZ900 Shop manual, maybe will help....
OMR
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: high compression
16 May 2010 09:56
i had no problem with my 1327cc when i used a honda starter.
Can u give us some more details on your exact issue.
cranking psi would be good to know here.
Can u give us some more details on your exact issue.
cranking psi would be good to know here.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- rspector
-
Topic Author
- Offline
- User
-

Registered
- Posts: 22
- Thanks: 0
Re: high compression
16 May 2010 16:39 - 16 May 2010 16:45
cranking psi is about 165. I have rebuilt one, needles springs rollers ect. When that one went it pushed the needles in enough to dent the back of the starter clutch. Its on its second now that I purchased off ebay (maybe the issue) but it looked fine. It seems like it just fails when your in mid crank and the engine fires. Now i'm getting the whiring noise of the starter still spinning after the engine starts(starter clutch not disengaging). It has the kick start, but I ca'nt kick the bike over myself. I should try the honda starter, i'm wondering if a weak starter can hurt the starter clutch?
Will the damper rubber cause catastrophic starter clutch problems? Because I will def check that , thanks for the info
Will the damper rubber cause catastrophic starter clutch problems? Because I will def check that , thanks for the info
Last edit: 16 May 2010 16:45 by rspector.
Please Log in or Create an account to join the conversation.
- PLUMMEN
-
- Offline
- User
-

Registered
- Posts: 7983
- Thanks: 104
Re: high compression
16 May 2010 17:51
165 aint much cranking psi,shouldnt be a major issue
Still recovering,some days are better than others.
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: high compression
17 May 2010 15:11
my 1200cc has 205 psi and no trouble with the Honda starter.
i wonder if u are getting a kick back that destroys the clutch?
this doesn’t sounds like a starter problem, but i do wonder if it turns over too slow, if that could affect the clutch with kick back?
i wonder if u are getting a kick back that destroys the clutch?
this doesn’t sounds like a starter problem, but i do wonder if it turns over too slow, if that could affect the clutch with kick back?
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- hocbj23
-
- User
-

Public
- Thanks: 0
Re: high compression
17 May 2010 15:48
see if u can find an ELR starter and clutch.That should do it.
Please Log in or Create an account to join the conversation.
- keith1
-
- Offline
- User
-

Registered
- Posts: 1646
- Thanks: 3
Re: high compression
17 May 2010 17:39
rspector wrote:
you might very well be using the wrong size(thickness) damper....if your starter is good and the pins and rollers are good and everything is put together right,using the wrong size damper can kill the whole deal in short order....too thin and it wont engage right and if too thick, will drag the starter to an early death....
redlinecycle.com/Starter%20Clutch%20Tech.html
here is a link above to explain.....you should get that baby to start right.....g/l....keith
cranking psi is about 165. I have rebuilt one, needles springs rollers ect. When that one went it pushed the needles in enough to dent the back of the starter clutch. Its on its second now that I purchased off ebay (maybe the issue) but it looked fine. It seems like it just fails when your in mid crank and the engine fires. Now i'm getting the whiring noise of the starter still spinning after the engine starts(starter clutch not disengaging). It has the kick start, but I ca'nt kick the bike over myself. I should try the honda starter, i'm wondering if a weak starter can hurt the starter clutch?
Will the damper rubber cause catastrophic starter clutch problems? Because I will def check that , thanks for the info
you might very well be using the wrong size(thickness) damper....if your starter is good and the pins and rollers are good and everything is put together right,using the wrong size damper can kill the whole deal in short order....too thin and it wont engage right and if too thick, will drag the starter to an early death....
redlinecycle.com/Starter%20Clutch%20Tech.html
here is a link above to explain.....you should get that baby to start right.....g/l....keith
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
