More noob reassembly questions
- chrispysaki
-
Topic Author
- Offline
- User
-

Registered
- Posts: 150
- Thanks: 0
More noob reassembly questions
26 May 2010 08:04
I have the piston rings compressed with plastic strips from a 2-liter coke bottle and zip ties. Are there any tricks or cautions to getting them into the jugs?
Also, I don't know if this applies to all kz's, but my FSM says to align the top ring with the gap facing forward, the second ring facing the rear and the two oil rings off-set about 30 degrees from center-forward. Once the piston rings were compressed, the rings were still generally facing these directions — how crucial is this part?
I have all four pistons compressed, but I wasn't sure if I should try all four at the same time, or start with 2/3 and then go for 1/4. The FSM says to do all four at once, but it seems like it'd be easier doing two at a time.
Thanks
Also, I don't know if this applies to all kz's, but my FSM says to align the top ring with the gap facing forward, the second ring facing the rear and the two oil rings off-set about 30 degrees from center-forward. Once the piston rings were compressed, the rings were still generally facing these directions — how crucial is this part?
I have all four pistons compressed, but I wasn't sure if I should try all four at the same time, or start with 2/3 and then go for 1/4. The FSM says to do all four at once, but it seems like it'd be easier doing two at a time.
Thanks
Please Log in or Create an account to join the conversation.
- Jack
-
- Offline
- User
-

Registered
- Posts: 691
- Thanks: 7
Re: More noob reassembly questions
26 May 2010 08:11
Personally I like the 2-3, then 1-4 method.The piston rings will move around once the motor is run but starting off with ring gaps opposed is the way I was shown & wouldn't worry about the small movement you mentioned. Hope this helps.
79 KZ 1075 MKll
79 KZ 1500 MKll dragbike
Gone but not forgotten:
3 X 73 Z1's
1 X 74 Z1A
1 X 75 Z1B
79 KZ 1500 MKll dragbike
Gone but not forgotten:
3 X 73 Z1's
1 X 74 Z1A
1 X 75 Z1B
Please Log in or Create an account to join the conversation.
- Kawickrice
-
- Offline
- User
-

Registered
- After Monday & Tuesday, even the calendar says WTF
- Posts: 2469
- Thanks: 20
Re: More noob reassembly questions
26 May 2010 08:52
Are you using a piece of wood with a rod notch to rest the piston bottoms on while you are fiddling?
73 Kawasaki Z1
07 HD CVO Ultra Classic
82 Suzuki GS 1100
74 Yamaha RD 350 (My two stroke toy)
77 Kawasaki KZ 650B-1 (My putt around bike)
80 Indian Moped (My American Iron)
1
Long Gone
75 Suzuki GT550
74 GT 380
79 RD 400 Daytona Special
72 Honda CL 175
74 Honda QA 50
Tampa FL
07 HD CVO Ultra Classic
82 Suzuki GS 1100
74 Yamaha RD 350 (My two stroke toy)
77 Kawasaki KZ 650B-1 (My putt around bike)
80 Indian Moped (My American Iron)
1
Long Gone
75 Suzuki GT550
74 GT 380
79 RD 400 Daytona Special
72 Honda CL 175
74 Honda QA 50
Tampa FL
Please Log in or Create an account to join the conversation.
- Jodyb17
-
- Offline
- User
-

Registered
- Posts: 81
- Thanks: 0
Re: More noob reassembly questions
26 May 2010 10:26
So is the plastic going to just slide out after you have the pistons in the cylinders?
1977 KZ 650 C
Please Log in or Create an account to join the conversation.
- EricHa
-
- Offline
- User
-

Registered
- Posts: 138
- Thanks: 1
Re: More noob reassembly questions
26 May 2010 10:48 - 26 May 2010 10:52
As a noob myself here's my experience, or lack thereof. I used heavy construction paper for the strips, but yes you're ready to coax the pistons in. Don't force anything! First time around I had one of the small 3 piece oil rings not make it in and tried to force it, ruined the ring. I had to buy another complete set for that hole. Second time I had the strips and ties right above the top ring on the piston, and slowly moved the cylinder down onto them. I also used locking forceps to hold the strips so they wouldn't fall into the crankcase. Vise grips would work. Take it slow and you'll get it. Good luck!
1977 Kawasaki KZ900A5
1975 Honda CB550K
1996 Ducati 900SS CR
1975 Honda CB550K
1996 Ducati 900SS CR
Last edit: 26 May 2010 10:52 by EricHa.
Please Log in or Create an account to join the conversation.
- chrispysaki
-
Topic Author
- Offline
- User
-

Registered
- Posts: 150
- Thanks: 0
Re: More noob reassembly questions
26 May 2010 11:32
Kawickrice: I hadn't planned on using the wood blocks with notches cut out, but that's a great idea!
Jodyb17: That's the plan. Cut the zip ties & slide out the plastic. I think there's some saying about what happens to even the best laid plans, however.
EricHa: Thanks for the advice. That's about what my set up looks like. Did you have two people working on this? One to hold the jugs and another to massage the pistons in?
Jodyb17: That's the plan. Cut the zip ties & slide out the plastic. I think there's some saying about what happens to even the best laid plans, however.
EricHa: Thanks for the advice. That's about what my set up looks like. Did you have two people working on this? One to hold the jugs and another to massage the pistons in?
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: More noob reassembly questions
26 May 2010 12:17 - 26 May 2010 12:19
After having performed this task many times by myself, I can say that the wooden block/piston rest is a super valuable instrument with this task.
The second is OIL, lots of super slippery light motor oil. Inside the cylinders and all over the pistons and rings.
I hate ring compressors and refuse to use them.
I just use my hands.
On blocks that are bored out and dont have a decent chamfer at the bottom to help guide things, it can be tricky, but for stock stuff its a piece o' cake.
The ring alignment isnt crucial, but should be followed to letter. If they move around a little its ok, so long as they dont all line up, then you got problems.
...and make sure if you have the squigly oil expander ring, that is DOESNT OVERLAP!
or that cylinder will rip through oil
GL.
The second is OIL, lots of super slippery light motor oil. Inside the cylinders and all over the pistons and rings.
I hate ring compressors and refuse to use them.
I just use my hands.
On blocks that are bored out and dont have a decent chamfer at the bottom to help guide things, it can be tricky, but for stock stuff its a piece o' cake.
The ring alignment isnt crucial, but should be followed to letter. If they move around a little its ok, so long as they dont all line up, then you got problems.
...and make sure if you have the squigly oil expander ring, that is DOESNT OVERLAP!
or that cylinder will rip through oil
GL.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Last edit: 26 May 2010 12:19 by TeK9iNe.
Please Log in or Create an account to join the conversation.
- EricHa
-
- Offline
- User
-

Registered
- Posts: 138
- Thanks: 1
Re: More noob reassembly questions
26 May 2010 12:55 - 26 May 2010 13:03
chrispysaki wrote:
Just myself, I had thin pieces of wood to hold up the cylinders. I put a 17mm wrench on the crankshaft end to raise the pistons up to the cylinders. Then I removed the wood and got to work trying to shimmy the pistons in, one hand on the crankshaft wrench, one hand on a piston. The weight of the cylinder block did the rest. I may have gotten lucky, but this seems to have worked for me. I still haven't started the engine yet though!
EricHa: Thanks for the advice. That's about what my set up looks like. Did you have two people working on this? One to hold the jugs and another to massage the pistons in?
Just myself, I had thin pieces of wood to hold up the cylinders. I put a 17mm wrench on the crankshaft end to raise the pistons up to the cylinders. Then I removed the wood and got to work trying to shimmy the pistons in, one hand on the crankshaft wrench, one hand on a piston. The weight of the cylinder block did the rest. I may have gotten lucky, but this seems to have worked for me. I still haven't started the engine yet though!
1977 Kawasaki KZ900A5
1975 Honda CB550K
1996 Ducati 900SS CR
1975 Honda CB550K
1996 Ducati 900SS CR
Last edit: 26 May 2010 13:03 by EricHa.
Please Log in or Create an account to join the conversation.
- 1981jmotor
-
- Offline
- User
-

Registered
- shade tree mechanic
- Posts: 61
- Thanks: 0
Re: More noob reassembly questions
26 May 2010 13:03
You might try radiator hose clamps instead of the zip ties- they are cheap, strong, and most of all- infinitely adjustable. You can always use some sheet metal under them because the hose clamp buckle with hit the bottom of the cyl and possible allow the piston ring to pop up.
my .02 cents.....
my .02 cents.....
1981 Kawasaki CSR 1000
First bike ever at 14 years old was 1969 Honda CL 175.
Bought a brand new Honda CM400T at 16 years old in 1979.
First bike ever at 14 years old was 1969 Honda CL 175.
Bought a brand new Honda CM400T at 16 years old in 1979.
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: More noob reassembly questions
26 May 2010 14:04
The only thing I might add is you may want to take a small round file and "angle" the bottom edge of the cylinder tubes to help the rings slide in.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- Jack
-
- Offline
- User
-

Registered
- Posts: 691
- Thanks: 7
Re: More noob reassembly questions
26 May 2010 14:25
Excellent point Bountyhunter -the chamfer on the bottom of the sleeves makes it so much easier to get the rings started into the bore.
79 KZ 1075 MKll
79 KZ 1500 MKll dragbike
Gone but not forgotten:
3 X 73 Z1's
1 X 74 Z1A
1 X 75 Z1B
79 KZ 1500 MKll dragbike
Gone but not forgotten:
3 X 73 Z1's
1 X 74 Z1A
1 X 75 Z1B
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
