Clutch/transmission problem?

  • chrispysaki
  • chrispysaki's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 150
  • Thanks: 0

Clutch/transmission problem?

01 Jun 2010 08:56
#372578
I opened the bike up pretty hard the other day, and around 80-90 mph in 4th gear something happened. I lost power, but the engine revved really high, like it jumped down to third gear or the clutch engaged.

Now the bike runs pretty well, doesn't jump gears or anything, but it feels like the clutch is slipping a bit when I open the throttle - it just doesn't have quite the same power it did before this incident. My friction plates were near the service limit before, and I scuffed up the metal plates, so I'm assuming I just need new friction plates.

Is there a chance that it's more than that? I really hope I didn't just kill the transmission.

Thanks,
Chris

Please Log in or Create an account to join the conversation.

  • Capt America
  • Capt America's Avatar
  • Offline
  • User
  • User
    Registered
  • Born Bad
  • Posts: 186
  • Thanks: 1

Re: Clutch/transmission problem?

01 Jun 2010 09:11
#372582
I'm betting clutch plates... and I'd suggest if you're going to be getting on it like that, you replace the crappy weak stock springs and replace them with some heavier springs from Barnett or whichever product you like best.

Running an old twin they are one of the first things I replace.
Capt A merica
1983 K1 750 twin
Ontario, Canada.

Please Log in or Create an account to join the conversation.

  • TexasKZ
  • TexasKZ's Avatar
  • Offline
  • Platinum Member
  • Platinum Member
    Registered
  • Posts: 8423
  • Thanks: 2806

Re: Clutch/transmission problem?

01 Jun 2010 09:55
#372588
Pooped clutch plates seems likely.
1982 KZ1000 LTD parts donor
1981 KZ1000 LTD slowly moving toward resurrection
2000 ZRX1100 not ridden enough

www.kzrider.com/forum/11-projects/620336...amateur-build-thread

Please Log in or Create an account to join the conversation.

  • PLUMMEN
  • PLUMMEN's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7983
  • Thanks: 104

Re: Clutch/transmission problem?

01 Jun 2010 12:54
#372617
try adjusting your clutch first,its slipping B)
Still recovering,some days are better than others.

Please Log in or Create an account to join the conversation.

  • testarossa
  • testarossa's Avatar
  • Offline
  • User
  • User
    Registered
  • Attack life, it's only trying to kill you.
  • Posts: 3673
  • Thanks: 83

Re: Clutch/transmission problem?

01 Jun 2010 13:56
#372624
I'm with Plummen here. Adjust that cable first, it's free. If that doesn't work then order a clutch cover gasket and get inside and have a look. I'm betting that your friction plates are done. If you have to get in there, do as Capt America says and replace the springs as well. There cheaper than the new oil and gasket will be if you don't replace them, and have to get in there again if your clutch still slips after you replace the disks.
1978 KZ1000 A2 Click--->Build Thread
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Clutch/transmission problem?

01 Jun 2010 17:17
#372676
If not already done, would first perform clutch pushrod adjustment.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • chrispysaki
  • chrispysaki's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 150
  • Thanks: 0

Re: Clutch/transmission problem?

01 Jun 2010 22:37
#372759
Thanks all...friction plates and springs are on the way. I was pretty surprised that this happened after taking the head & cylinders off and adjusting the valve clearances and cams/timing.

I've been riding it pretty hard for the last month and nothing like this happened, so I immediately thought the worst. I guess there was just enough extra power there after the adjustments to reveal the plate wear.

The good news is that I rechecked the valve clearances & cam timing/sprockets and everything is perfectly within spec. It's pretty nice knowing I did at least one thing right with this bike!

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum