Identify this foreign material
- KZ250LTD
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1311
- Thanks: 16
Identify this foreign material
20 Jun 2010 17:50
So, pulled the head and barrels off the 1000 ST because I knew there was something wrong inside. I'd seen some red material coming out in the oil and it always sounded terrible + smoked, etc etc. Barrels and pistons looked good, valves looked a little fishy but generally okay. Pulled off the oil pan and was thankful that I'm not going crazy and didn't pull it all apart for no reason :laugh:
Not sure what this is. Clutch plate? Starter clutch maybe(I haven't checked it but the starter was working so I doubt it)?
Suggestions anyone?
Not sure what this is. Clutch plate? Starter clutch maybe(I haven't checked it but the starter was working so I doubt it)?
Suggestions anyone?
79 KZ1000ST
Past:
Many.
Past:
Many.
Please Log in or Create an account to join the conversation.
- larrycavan
-
- User
-

Public
- Thanks: 0
Re: Identify this foreign material
20 Jun 2010 17:53
It won't be starter clutch. That's just some rollers and springs.
Looks like friction plate shavings and a dab of silicone sealer.
Looks like friction plate shavings and a dab of silicone sealer.
Please Log in or Create an account to join the conversation.
- taildragger1197
-
- Offline
- User
-

Registered
- Posts: 113
- Thanks: 16
Re: Identify this foreign material
20 Jun 2010 18:01
Was the oil filter intact? The "orange" debris looks like someone got carried away with the gasket sealant.
Union City, Tennessee
1979 KZ1000 LTD B3
1979 KZ1000(1260)LTD S/G Pro ET
1993 ZX11 D1 Ninja
1979 KZ1000 LTD B3
1979 KZ1000(1260)LTD S/G Pro ET
1993 ZX11 D1 Ninja
Please Log in or Create an account to join the conversation.
- Vter Bob
-
- Offline
- User
-

Registered
- Posts: 493
- Thanks: 4
Re: Identify this foreign material
20 Jun 2010 18:15
Not to make light of your problem but...
OH NO! NOT ANOTHER "ORANGE" FILTER! :blink:
This is way out of my expertise, but I found some stuff that looked similar to that under the stator cover of my 1000. It was the glue they used to affix the magnets to the rotor. With the volume you show in the pics I doubt that's what it is. I don't think pieces that large could make it into the oil pan. Is it hard or pliable?
OH NO! NOT ANOTHER "ORANGE" FILTER! :blink:
This is way out of my expertise, but I found some stuff that looked similar to that under the stator cover of my 1000. It was the glue they used to affix the magnets to the rotor. With the volume you show in the pics I doubt that's what it is. I don't think pieces that large could make it into the oil pan. Is it hard or pliable?
Georgia, Vermont
1981 KZ550 LTD
1982 KZ1000 LTD
1999 ZG1000 Concours
Greetings from the Peoples Republic of Vermont, home of Ethan Allen, 2 American Presidents, a socialist US Senator and.....Homer & Bart Simpson
1981 KZ550 LTD
1982 KZ1000 LTD
1999 ZG1000 Concours
Greetings from the Peoples Republic of Vermont, home of Ethan Allen, 2 American Presidents, a socialist US Senator and.....Homer & Bart Simpson
Please Log in or Create an account to join the conversation.
- larrycavan
-
- User
-

Public
- Thanks: 0
Re: Identify this foreign material
20 Jun 2010 18:28
Vter Bob wrote:
Oh yea...you could well be right.
I took a second and better look at the pics. The piece on the glove looks like silicone at quick glance but when you go back up and look at the other pics, it does look a lot like the epoxy sealer used on the rotor magnets. The ST would have that type of rotor....
Not to make light of your problem but...
OH NO! NOT ANOTHER "ORANGE" FILTER! :blink:
This is way out of my expertise, but I found some stuff that looked similar to that under the stator cover of my 1000. It was the glue they used to affix the magnets to the rotor. With the volume you show in the pics I doubt that's what it is. I don't think pieces that large could make it into the oil pan. Is it hard or pliable?
Oh yea...you could well be right.
I took a second and better look at the pics. The piece on the glove looks like silicone at quick glance but when you go back up and look at the other pics, it does look a lot like the epoxy sealer used on the rotor magnets. The ST would have that type of rotor....
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Identify this foreign material
20 Jun 2010 19:21
For peace of mind(If it were me) I'd drop the alternator cover and inspect the stator and rotor for any loss of adhesive.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- KZ250LTD
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1311
- Thanks: 16
Re: Identify this foreign material
20 Jun 2010 19:58 - 20 Jun 2010 20:00
I doubt it is silicone, forgot to mention that it is very hard. That's why I figured it might be clutch plates. There was no sign of it in the barrels or on the pistons and just from a quick glance there doesn't seem to be much up inside the cases but the motor hasnt run for about a year so it may well have just had time to drop down
Edit:
and the oil filter appeared to be intact, don't think it is filter debris especially because it is so hard
Edit:
and the oil filter appeared to be intact, don't think it is filter debris especially because it is so hard
79 KZ1000ST
Past:
Many.
Past:
Many.
Last edit: 20 Jun 2010 20:00 by KZ250LTD.
Please Log in or Create an account to join the conversation.
- larrycavan
-
- User
-

Public
- Thanks: 0
Re: Identify this foreign material
20 Jun 2010 20:05
KZ250LTD wrote:
It's most likely the epoxy from the edge of the rotor magnets then. Yank the cover.
I doubt it is silicone, forgot to mention that it is very hard. That's why I figured it might be clutch plates. There was no sign of it in the barrels or on the pistons and just from a quick glance there doesn't seem to be much up inside the cases but the motor hasnt run for about a year so it may well have just had time to drop down
Edit:
and the oil filter appeared to be intact, don't think it is filter debris especially because it is so hard
It's most likely the epoxy from the edge of the rotor magnets then. Yank the cover.
Please Log in or Create an account to join the conversation.
- KZ250LTD
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1311
- Thanks: 16
Re: Identify this foreign material
20 Jun 2010 20:27
Well now, look at that. You guys were right, nice job 
I'll strip the rest off and once its back together run it and flush the oil a couple of times before any serious riding (it'll be awhile, this is just a side project). Does the epoxy need to be there? Should I replace it?
I'll strip the rest off and once its back together run it and flush the oil a couple of times before any serious riding (it'll be awhile, this is just a side project). Does the epoxy need to be there? Should I replace it?
79 KZ1000ST
Past:
Many.
Past:
Many.
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Identify this foreign material
20 Jun 2010 20:44
I'd try to remove as much lose material as possible because more can possibly come off.This may make the rotor unbalanced causing more problems in the future.
The trouble I see with using another adhesive would be in balancing it evenly. You might have to have the rotor re-glued. I wonder if a motor rebuilding shop could vacuum impregnate the magnets in a furnace(of course magnets and high temperature dont mix well).
The trouble I see with using another adhesive would be in balancing it evenly. You might have to have the rotor re-glued. I wonder if a motor rebuilding shop could vacuum impregnate the magnets in a furnace(of course magnets and high temperature dont mix well).
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- KZ250LTD
-
Topic Author
- Offline
- User
-

Registered
- Posts: 1311
- Thanks: 16
Re: Identify this foreign material
20 Jun 2010 21:18
Hmm... so the rotor wouldn't be balanced as is without the adhesive? What would the possible consequences of running it w/out the epoxy be?
79 KZ1000ST
Past:
Many.
Past:
Many.
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Identify this foreign material
20 Jun 2010 21:26Identify this foreign material
It looks Irish to me......
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
