valve clearances
- cdulmage
-
Topic Author
- Offline
- User
-

Registered
- Posts: 3
- Thanks: 0
valve clearances
15 Aug 2010 08:04
I have a question my kz1100 d1 needs shims
all valves messure between 2 and 4 the spec is 5 to 15
now the question
What is the + or - difference if
I get -5 shims and set the range at 5 to 10
or -10 shims for a 10 to 15 range
_
all valves messure between 2 and 4 the spec is 5 to 15
now the question
What is the + or - difference if
I get -5 shims and set the range at 5 to 10
or -10 shims for a 10 to 15 range
_
Please Log in or Create an account to join the conversation.
- otakar
-
- Offline
- User
-

Registered
- Posts: 5069
- Thanks: 29
Re: valve clearances
15 Aug 2010 08:21
If you ride very "sportingly" you will be better off with the smaller gaps. This will give you more lift and less chance of spitting a shim if you over-rev occasionally. If you ride to "cruise" you will be better with he little larger gap because there will be more time between having to re-adjust them again. With the larger gap the bike will have a bit more "hiss" at the top end. Running the right kind of oil can also increase the time interval between re-adjustments.
74 Z1-A stock
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000
Please Log in or Create an account to join the conversation.
- T_Dub
-
- Offline
- User
-

Registered
- Posts: 1441
- Thanks: 26
Re: valve clearances
15 Aug 2010 08:25 - 15 Aug 2010 08:25
Otakar is absolutely right, as usual.
1977 KZ650B1
-810cc
-Cavanaugh Racing Head
-Mikuni RS34's
-GPR Muffler
-810cc
-Cavanaugh Racing Head
-Mikuni RS34's
-GPR Muffler
Last edit: 15 Aug 2010 08:25 by T_Dub.
Please Log in or Create an account to join the conversation.
- Jeff.Saunders
-
- Offline
- Vendor
-

Vendors
- Posts: 1238
- Thanks: 149
Re: valve clearances
15 Aug 2010 08:29
cdulmage wrote:
You are mixing measurement units.
0.002" - 0.006" is the recommended clearance in INCH
0.05mm - 0.15mm is the recommended clearance in MM
If you have a minimum of 2 thou clearance you are OK to run the engine. I try and set mine to around 4 thou clearance and never leave it set at 2 thou as the next time you check the valves the clearance will be UNDER spec.
I have a question my kz1100 d1 needs shims
all valves messure between 2 and 4 the spec is 5 to 15
now the question
What is the + or - difference if
I get -5 shims and set the range at 5 to 10
or -10 shims for a 10 to 15 range
_
You are mixing measurement units.
0.002" - 0.006" is the recommended clearance in INCH
0.05mm - 0.15mm is the recommended clearance in MM
If you have a minimum of 2 thou clearance you are OK to run the engine. I try and set mine to around 4 thou clearance and never leave it set at 2 thou as the next time you check the valves the clearance will be UNDER spec.
Please Log in or Create an account to join the conversation.
- otakar
-
- Offline
- User
-

Registered
- Posts: 5069
- Thanks: 29
Re: valve clearances
15 Aug 2010 08:41
Jeff.Saunders wrote:
I just made the presumption that he had the gap "units" right in his head. But it is a very good point, to make sure that the units of measure are not confused.
cdulmage wrote:I have a question my kz1100 d1 needs shims
all valves messure between 2 and 4 the spec is 5 to 15
now the question
What is the + or - difference if
I get -5 shims and set the range at 5 to 10
or -10 shims for a 10 to 15 range
_
You are mixing measurement units.
0.002" - 0.006" is the recommended clearance in INCH
0.05mm - 0.15mm is the recommended clearance in MM
If you have a minimum of 2 thou clearance you are OK to run the engine. I try and set mine to around 4 thou clearance and never leave it set at 2 thou as the next time you check the valves the clearance will be UNDER spec.
I just made the presumption that he had the gap "units" right in his head. But it is a very good point, to make sure that the units of measure are not confused.
74 Z1-A stock
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: valve clearances
15 Aug 2010 08:54An uncertain about KZ1100 valve clearance specs, but for Z1-KZ900-KZ1000, FSM specifies .05mm ~ .10mm, and that some very knowledgeable folks currently recommend .10mm ~ .15mm, at least for everyday riding.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
