Bolt problem; 78 KX1000A2

  • zeerex99
  • zeerex99's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 5
  • Thanks: 0

Bolt problem; 78 KX1000A2

11 Sep 2010 11:47
#397665
Need some advice. Have been rebuilding a 78 KZ1000A2. I bought a NOS head including cam bearing caps and bolts. I installed the cams and started bolting down the bearing caps. My shop manual says to torque to 13.5 ft/lbs. The first bolt snapped off well before I hit the setting. The spec I'm using is 13.5 ft/lbs. Foolishly I continued and had mixed luck with the next five. Some tourqued and some snapped.

I looked at the snapped bolts. They appear to be deffective where the breaks happened. Maybe stress cracking? Not sure. They are 32 years old but so are the ones currently in nthe bike.

Any advice? Should I re-use the original bolts? Try to buy new ones? My biggest problem now is getting the snapped off bolts out of a new head. Patience, patience, patience!

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Bolt problem; 78 KX1000A2

11 Sep 2010 12:02
#397668
There are some current posts on those cam caps. The Book is wrong on the torque, many people have read that spec and striped the threads out. 1/4" ratchet is all you need, torque is in Inch pounds. Most service manuals also have a guide for torque per bolt/ thread size/ type. Those puny little 6mm bolts will never take 13ft. lbs.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • zeerex99
  • zeerex99's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 5
  • Thanks: 0

Re: Bolt problem; 78 KX1000A2

11 Sep 2010 12:20
#397672
So....what torque spec should I use? I've put enough money into this rebuild that I'm not willing to even turn it over, let alone close it up if I'm going to spin cam bearings! Anyone????

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Bolt problem; 78 KX1000A2

11 Sep 2010 12:31
#397677
Try here,
kzrider.com/index.php?option=com_kunena&...ew&catid=2&id=395574
There is some discussion on this very issue.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Bolt problem; 78 KX1000A2

11 Sep 2010 13:44
#397692
zeerex99 wrote:
So....what torque spec should I use? I've put enough money into this rebuild that I'm not willing to even turn it over, let alone close it up if I'm going to spin cam bearings! Anyone????
I use about 90 INCH-POUNDS on cam bolts. That's about 7.5 FT-LBS but you must have a low range wrench to get it accurate.
1979 KZ-750 Twin

Please Log in or Create an account to join the conversation.

  • DFIGPZ
  • DFIGPZ's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 615
  • Thanks: 121

Re: Bolt problem; 78 KX1000A2

11 Sep 2010 17:08
#397793
yes T/Q 90in lbs you will be good to go
1984 750 Turbo

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: Bolt problem; 78 KX1000A2

11 Sep 2010 19:21
#397833
OK; tell us what manual gave that spec?? I'm betting on Clymers. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Bolt problem; 78 KX1000A2

11 Sep 2010 19:33
#397837
My factory shop manual for my 1982 GPz1100 B2 model had for the 16 M6x1.0 cam bearing caps as 12 foot pounds, I found out it should have been 66 Inch pounds and changed it in the manual.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: Bolt problem; 78 KX1000A2

11 Sep 2010 20:29
#397854
I asked because all the Kawasaki factory service manuals (from 1976 up) for the KZ650 show 95-113 IN lbs. That's 7.9 - 9.4 FT lbs. I suspect that the big engine cam caps are different, but 12 FT lbs sounds like a whole bunch if they are 6mm bolts. I set my torque wrench at 100 IN lbs and had no problems. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Bolt problem; 78 KX1000A2

11 Sep 2010 20:45
#397858
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • Gman
  • Gman's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 147
  • Thanks: 5

Re: Bolt problem; 78 KX1000A2

12 Sep 2010 03:33
#397950
Don't know if this is any help but at the Honda factory we use 0.7 - 1.2kgf for any normal 6mm bolt or nut. If you go much more than that, you start stretching the bolt or stud.
1978 KZ1000
1965 Harly Electra Glide
2002 Gold Wing
1974 Z1 900 project

Please Log in or Create an account to join the conversation.

  • zeerex99
  • zeerex99's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 5
  • Thanks: 0

Re: Bolt problem; 78 KX1000A2

12 Sep 2010 16:06
#398088
The manual that came with this bike is indeed a Clymers. This is my first experience with any manual (car or bike) giving a torque value that far off. Then again, it's the only Clymer manual I've ever used. Haven't tried pulling the broken bolt ends out yet. At least the threads didn't strip on the head.

I bought the factory shop manual when I got my ZRX1100 and there's no comparison to the Clymer manual.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum