good compression?

  • Lazyman06
  • Lazyman06's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 257
  • Thanks: 3

good compression?

18 Sep 2010 11:10
#399634
ran the compression while ago. tell me what ya'll think.
Cylinder
#1 120 psi
#2 120 psi
#3 107 psi
#4 130 psi
The number 3 cylinder is what scares me with all the other cylinders being so high why is number 3 so much different.
1979 KZ1000 MK II frame
1980 KZ1000 C3 police engine

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: good compression?

18 Sep 2010 11:29
#399638
Lazyman06 wrote:
ran the compression while ago. tell me what ya'll think.
Cylinder
#1 120 psi
#2 120 psi
#3 107 psi
#4 130 psi
The number 3 cylinder is what scares me with all the other cylinders being so high why is number 3 so much different.

Specs:
Standard 128~156 psi
Service limit 100 psi w/ <14 psi dif b/w cyl

Could do leak-down test to determine where compression is escaping.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • muddy1
  • muddy1's Avatar
  • Offline
  • User
  • User
    Registered
  • 1980 Kz1000 LTD B4
  • Posts: 136
  • Thanks: 0

Re: good compression?

18 Sep 2010 11:30
#399640
How do the plugs look? Does it smoke? It's pretty close to the 10% rule, have you looked through the spark plug holes for carbon build-up on the pistons?
1970 SL-70
1972 CB 750
1973 Z1
1976 YZ 125
1976 KZ400
1979 KZ400 LTD
1980 KZ1000 LTD B4
1984 YZ 490
1989 750 Ninja

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: good compression?

18 Sep 2010 11:33
#399642
Several things can cause this:

1."Tight Valves", Having clearances that need a thinner shim between the cam(s) and valve bucket.

2.Carbon build up on #3 valves holding them partially open.

3.Stuck piston rings, letting compression go by the piston.

Engine Chemicals:

Mopar Combustion Chamber Cleaner # 04318001. Designed to remove carbon from combustion chambers & valves.

www.amazon.com/Yamaha-Ring-Additive-32oz...-32-00/dp/B002GUCLH2 (Yamaha Ring Free)
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • Lazyman06
  • Lazyman06's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 257
  • Thanks: 3

Re: good compression?

18 Sep 2010 12:28
#399651
there is carbon on the piston so logic can deduct that there is carbon on the valves as well. it setting up as long as it has the rings might need to be set in again. it probably just needs to be ran to work the crap out of it's system
1979 KZ1000 MK II frame
1980 KZ1000 C3 police engine

Please Log in or Create an account to join the conversation.

  • TeK9iNe
  • TeK9iNe's Avatar
  • Offline
  • User
  • User
    Registered
  • What did you do!?!
  • Posts: 2436
  • Thanks: 28

Re: good compression?

18 Sep 2010 12:39
#399653
Lazyman06 wrote:
there is carbon on the piston so logic can deduct that there is carbon on the valves as well. it setting up as long as it has the rings might need to be set in again. it probably just needs to be ran to work the crap out of it's system

Take her out for an hour or so, then do the compression test. Hot numbers are what matter on the old air cooled stuff, unless the bike is particularily hard to start, and has horrible low numbers cold.

Coul just need a valve lap job. Won't know without further diagnosis.

Good luck.

B)
Motorcycle Shop Owner/Operator

79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors ;)

Please Log in or Create an account to join the conversation.

  • Lazyman06
  • Lazyman06's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 257
  • Thanks: 3

Re: good compression?

18 Sep 2010 18:54
#399762
yea is definitely cold lol so when I get it out next week i'll run it again
1979 KZ1000 MK II frame
1980 KZ1000 C3 police engine

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum