Lacking power, and running rough? Help

  • Dylansword
  • Dylansword's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 32
  • Thanks: 0

Re: Timing marks on 77 kz650?

02 Oct 2010 19:57
#403602
OK so, its reading about 13.2 around 1200rpms, and up toward 4-5k, it goes down to 12.9 or so. The battery is low, from cranking the engine. Im having to kick start it. It seemed to drop voltage when revved up, and produce more toward an idle.

Please Log in or Create an account to join the conversation.

  • Dylansword
  • Dylansword's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 32
  • Thanks: 0

Re: Timing marks on 77 kz650?

02 Oct 2010 20:09
#403604
What is a good way to get the carbs clean? My air compressor is broken btw.

Please Log in or Create an account to join the conversation.

  • TeK9iNe
  • TeK9iNe's Avatar
  • Offline
  • User
  • User
    Registered
  • What did you do!?!
  • Posts: 2436
  • Thanks: 28

Re: Lacking power, and running rough? Help

02 Oct 2010 20:22 - 02 Oct 2010 20:24
#403607
OK, so when setting the timing, your lining up the case mark with th "F" mark via the timing light, not the "T" mark. Correct??? With Dyna S, set the timing once and never touch it again unless modding.

If your battery is showing higher voltage at idle than at full advance (3500rpm+), then something in your charging system is dead/not working properly. When you rev the bike up it should be @ 14.5 VDC from 3500 - max rpm. about 13+ VDC at idle.

A compression check is an absolute must to determine engine condition. Valve gaps are considered regular maintenence in the manual, and should be adjusted before the bike is placed into regular opperation to prevent -- BOOM! :laugh: If valve gaps too large, loud valves. If gaps too tight, burnt valves and burp hiccup, bang.

The black smoke/backfiring crap has nothing to do with either of those anyways.

Clean the carbs thoroughly with a good spray carb cleaner after you have removed ALL the rubber bits.

Spray through all the jets, and thier ports in the carb while looking down the carb barrel to ensure that cleaner is blowing through freely.

Make sure to hold the pilot jets up to a light, and you should be able to see right through. If you cant spray through a pilot jet, then use a small piece of steel brush wire, and carefully poke it through.

When re-assembling, make sure that carbs/airbox/filter are all installed absolutely air tight, else it will not run correctly.

Do it, just DO IT.

B)
Motorcycle Shop Owner/Operator

79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors ;)
Last edit: 02 Oct 2010 20:24 by TeK9iNe.

Please Log in or Create an account to join the conversation.

  • Dylansword
  • Dylansword's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 32
  • Thanks: 0

Re: Lacking power, and running rough? Help

02 Oct 2010 20:28
#403609
ok, ill pull the carbs again. I pulled all the jets and blew thru them. Is there any other tests i can do?

Please Log in or Create an account to join the conversation.

  • nads.com
  • nads.com's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 993
  • Thanks: 20

Re: Lacking power, and running rough? Help

02 Oct 2010 22:22
#403620
Just because you can see through a jet doesn'
t mean it's clean. A 650 needs very clean carbs with stock jetting. Id pole something through the pilot jets and make certain the passages in the carb are clean. The timing can't be right if it's not near the fire mark. Check for a fouled plug or a cylinder with no gas by feeling the pipes warm up. A bad plug cap can cause a miss check them for open. Don't forget to check the advancer that will stop you in your tracks if it's stuck.

Please Log in or Create an account to join the conversation.

  • gcarson64
  • gcarson64's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 63
  • Thanks: 0

Re: Lacking power, and running rough? Help

02 Oct 2010 23:01
#403622
have you adjusted the carbs, black smoke is unburt gas so it could be to rich have you sincd the carbs if not i would do that.
1980 kz550 38,500 miles basket case ( soon to be a BOBBER )

1983 kz550 9,600 miles

1988 jeep grand wagoneer 144,500 miles 4 mpg

Please Log in or Create an account to join the conversation.

  • Dylansword
  • Dylansword's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 32
  • Thanks: 0

Re: Lacking power, and running rough? Help

03 Oct 2010 12:23
#403795
I cleaned the carbs. And all the jets and passages. And it didnt change anything. So, i am strongly thinking it is the dyna electronic ignition. It seems to have spark at all cylinders, just weak? What can i do to test the dyna? Thanks

Please Log in or Create an account to join the conversation.

  • TeK9iNe
  • TeK9iNe's Avatar
  • Offline
  • User
  • User
    Registered
  • What did you do!?!
  • Posts: 2436
  • Thanks: 28

Re: Lacking power, and running rough? Help

03 Oct 2010 20:29
#403909
Just gap a plug real tall and see if it still transfers spark, or buy a spark tester tool. They are very inexpensive.

Like said, check exhaust header temps at idle. Mist some water on them and it should sizzle right away after just a couple minutes of idling. You can also try quickly tapping the pipes, but they are very hot - tap fast! :laugh:

If one or more is not hot, then it could be an ignition issue, bad compression, or poor mixture settings, air leak, poor carb sync, head gasket leak, tight valves, etc....

Best of luck.

B)
Motorcycle Shop Owner/Operator

79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors ;)

Please Log in or Create an account to join the conversation.

  • TorreyJ
  • TorreyJ's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 72
  • Thanks: 1

Re: Lacking power, and running rough? Help

17 May 2011 01:43
#451645
Dylansword wrote: I suspect the timing now. So my qestion it, what are the timing marks? Or what may it be? Thank you very much.

That, my fellow KZ'er, what a fantastic sentence. Can you diagram it? :)

Please Log in or Create an account to join the conversation.

  • TorreyJ
  • TorreyJ's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 72
  • Thanks: 1

Re: Timing marks on 77 kz650?

17 May 2011 02:03
#451649
Dylansword wrote: 1 OK, so now, itit starts and runs.

2 Could somehting in the ignition system have blown.

3 Ive cleaed the carbs twice. Could all it is, is a clogged carb?

4 Oh, and it did it once, then seemed to clear up for the ride home, then started after i hot rodded it again. Thanks

5 I got my timing light on it, and if its advanced all the way, the still dont line up.

6 Could something faulty in the ignition system cause, backfiring, black smoke, carbonated plugs, lacking of power, and general running rough? If so, what could be causing it? Thanks


1.ITIT is a great name for your bike!
Why? be cause I TIT too!

2.What exactly could "blow" in the ignition system. Maybe you "blew a point rod ignightor bearing? Check the manual for the settings.

3.Just by reading this sentence I would recommend that you do not ever disassemble anything mechanical.

4.If you "hot rodded" it and it screwed it up, then, it was normal again, why would you repeat this behavior?

5.what are you trying to line up your still with, and how do you install still's on a bike?

6. This questions SCREAMS that the next thing you should do is take it to someone who can fix it for you. You aren't going to learn basic mechanics here.

Just my thoughts.
Go hard or go home.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum