Clearancing Head for Cams - Photo?
- DoubleDub
-
Topic Author
- User
-

Public
- Thanks: 0
Clearancing Head for Cams - Photo?
05 Nov 2010 12:37
Does anyone have a photo that shows what the areas need to be clearanced for higher lift cams?
I'm considering getting a set this winter for my Kz and was just curious. I'll likely end up with a drop-in set, but I'm curious where and how much material typically needs to get removed and since I don't have a set of non-drop-in cams I'm having a tough time visualizing what needs to be done (although I think I have an idea?).
Thanks in advance!
I'm considering getting a set this winter for my Kz and was just curious. I'll likely end up with a drop-in set, but I'm curious where and how much material typically needs to get removed and since I don't have a set of non-drop-in cams I'm having a tough time visualizing what needs to be done (although I think I have an idea?).
Thanks in advance!
Please Log in or Create an account to join the conversation.
- testarossa
-
- Offline
- User
-

Registered
- Attack life, it's only trying to kill you.
- Posts: 3673
- Thanks: 83
Re: Clearancing Head for Cams - Photo?
05 Nov 2010 13:04
DoubleDub wrote:
X2 Plummen said he was going to do just this thing, but I somehow missed the post.
Does anyone have a photo that shows what the areas need to be clearanced for higher lift cams?
I'm considering getting a set this winter for my Kz and was just curious. I'll likely end up with a drop-in set, but I'm curious where and how much material typically needs to get removed and since I don't have a set of non-drop-in cams I'm having a tough time visualizing what needs to be done (although I think I have an idea?).
Thanks in advance!
X2 Plummen said he was going to do just this thing, but I somehow missed the post.
1978 KZ1000 A2 Click--->Build Thread
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN
Please Log in or Create an account to join the conversation.
- Injected
-
- Offline
- User
-

Registered
- Posts: 1846
- Thanks: 1286
Re: Clearancing Head for Cams - Photo?
05 Nov 2010 13:05
Which KZ?
For my 650 the cover is high so unless your running over .400" then it does not have to be ground... I think the 900 might have some "X"'s cast in the cover to deal with.
As for the head, the area is the cam lobe pathway from the insides of where the bucket rides up and down to the gasket surface on both sides of the bucket hole... usually have to take roughly 1/8" out of there - it depends how big the cams are... you can't take so much as to ruin the gasket surface.
Don't have a photo to show you... think I explained it good enough.
For my 650 the cover is high so unless your running over .400" then it does not have to be ground... I think the 900 might have some "X"'s cast in the cover to deal with.
As for the head, the area is the cam lobe pathway from the insides of where the bucket rides up and down to the gasket surface on both sides of the bucket hole... usually have to take roughly 1/8" out of there - it depends how big the cams are... you can't take so much as to ruin the gasket surface.
Don't have a photo to show you... think I explained it good enough.
1978 KZ650B2 w 1197cc Z1 engine
1977 KZ650B1 w 750cc Spectre engine
1979 KZ650C3 w 831cc Hot Rod engine
1978 KZ650C2 w 762cc DFI project
1977 KZ650C1 stock restoration project
1978 KZ650B2 modified project
1977 KZ650B1 w 750cc Spectre engine
1979 KZ650C3 w 831cc Hot Rod engine
1978 KZ650C2 w 762cc DFI project
1977 KZ650C1 stock restoration project
1978 KZ650B2 modified project
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Clearancing Head for Cams - Photo?
05 Nov 2010 14:58 - 05 Nov 2010 15:03
Inside surface of stock valve cover (see image) may need relieving (by grinding down the X marks) to prevent contact by cam lobe.
Good Fortune!
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 05 Nov 2010 15:03 by Patton.
Please Log in or Create an account to join the conversation.
- DoubleDub
-
Topic Author
- User
-

Public
- Thanks: 0
Re: Clearancing Head for Cams - Photo?
05 Nov 2010 15:25
Injected wrote:
Thanks, that helps, but I'd love to see a clearanced head to compare to my stock head.
I think the 900/1000 heads were similar with a lift over .400 requiring clearancing, although I remember Larry preaching that you should never assume and always double check with aftermarket cams .... :silly:
Patton - you wouldn't happen to have a picture of a clearanced head near the buckets would you?
Which KZ?
For my 650 the cover is high so unless your running over .400" then it does not have to be ground... I think the 900 might have some "X"'s cast in the cover to deal with.
As for the head, the area is the cam lobe pathway from the insides of where the bucket rides up and down to the gasket surface on both sides of the bucket hole... usually have to take roughly 1/8" out of there - it depends how big the cams are... you can't take so much as to ruin the gasket surface.
Don't have a photo to show you... think I explained it good enough.
Thanks, that helps, but I'd love to see a clearanced head to compare to my stock head.
I think the 900/1000 heads were similar with a lift over .400 requiring clearancing, although I remember Larry preaching that you should never assume and always double check with aftermarket cams .... :silly:
Patton - you wouldn't happen to have a picture of a clearanced head near the buckets would you?
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Clearancing Head for Cams - Photo?
05 Nov 2010 15:53
DoubleDub wrote:
Sorry, no pic of clearanced head near the buckets.
Am also learning from this thread.
Guessing the described relief would be from the area indicated in red on this pic (both sides of bucket tower, but one side hidden by lobe in this pic).
Good Fortune!
[Click on image to enlarge view.]
Injected wrote:Thanks, that helps, but I'd love to see a clearanced head to compare to my stock head....KZ...900 might have some "X"'s cast in the cover to deal with.
As for the head, the area is the cam lobe pathway from the insides of where the bucket rides up and down to the gasket surface on both sides of the bucket hole... usually have to take roughly 1/8" out of there - it depends how big the cams are... you can't take so much as to ruin the gasket surface.
Don't have a photo to show you... think I explained it good enough.
...happen to have a picture of a clearanced head near the buckets....
Sorry, no pic of clearanced head near the buckets.
Am also learning from this thread.
Guessing the described relief would be from the area indicated in red on this pic (both sides of bucket tower, but one side hidden by lobe in this pic).
Good Fortune!
[Click on image to enlarge view.]
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Clearancing Head for Cams - Photo?
05 Nov 2010 16:00
On second thought, may be referencing the area shown in blue.
Seems pretty scary to me --- cutting into an already thin gasket mating surface.
Good Fortune!
Seems pretty scary to me --- cutting into an already thin gasket mating surface.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Please Log in or Create an account to join the conversation.
- Injected
-
- Offline
- User
-

Registered
- Posts: 1846
- Thanks: 1286
Re: Clearancing Head for Cams - Photo?
05 Nov 2010 16:14 - 05 Nov 2010 16:18
That second picture with the red and blue is exactly what I am talking about... my head is currently on the bike and all buttoned up for its winter nap, so no chance of a pic... but yes if you need to thin the gasket flange, it is what it is, cam can't rotate without clearance - no issues so far.
I went almost half way across the gasket flange - only as wide as the lobe, because I am running a massive cam in the 650 head.
So I guess the pics are already up...
I went almost half way across the gasket flange - only as wide as the lobe, because I am running a massive cam in the 650 head.
So I guess the pics are already up...
1978 KZ650B2 w 1197cc Z1 engine
1977 KZ650B1 w 750cc Spectre engine
1979 KZ650C3 w 831cc Hot Rod engine
1978 KZ650C2 w 762cc DFI project
1977 KZ650C1 stock restoration project
1978 KZ650B2 modified project
1977 KZ650B1 w 750cc Spectre engine
1979 KZ650C3 w 831cc Hot Rod engine
1978 KZ650C2 w 762cc DFI project
1977 KZ650C1 stock restoration project
1978 KZ650B2 modified project
Last edit: 05 Nov 2010 16:18 by Injected.
Please Log in or Create an account to join the conversation.
- keith1
-
- Offline
- User
-

Registered
- Posts: 1646
- Thanks: 3
Re: Clearancing Head for Cams - Photo?
05 Nov 2010 17:37
Patton wrote:
you are correct sir on a 900/1000....i have a decent example in the garage i just referenced...i believe it to be good for .410 cams if anyone is interested.....
you are correct sir on a 900/1000....i have a decent example in the garage i just referenced...i believe it to be good for .410 cams if anyone is interested.....
Please Log in or Create an account to join the conversation.
- kzz1p
-
- Offline
- User
-

Registered
- One Test Is Worth A Thousand Expert Opinions!
- Posts: 1432
- Thanks: 3
- keith1
-
- Offline
- User
-

Registered
- Posts: 1646
- Thanks: 3
Re: Clearancing Head for Cams - Photo?
05 Nov 2010 17:56 - 05 Nov 2010 17:58
Last edit: 05 Nov 2010 17:58 by keith1.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
