Oil Cooler Line

  • grumpy56
  • grumpy56's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 310
  • Thanks: 6

Oil Cooler Line

28 Dec 2010 16:50
#418959
Have a leak where my oil cooler line attaches to the oil pressure switch (I think). It's hard to tell whether it is the oil line or the housing to which the oil pressure switch is attached. Removed the oil line and needed help with two things: (1) How can I tell if my line is any good? Does anyone pressure test them? (2) Any suggestions on where to get a new line? Since I have it off I figure I may just as well replace it. Thank you.
Lewis
1982 KZ1000-J2
2006 HD FXD35
1970 Suzuki T350
1972 Suzuki GT380 (In-Process)
In The Past...71 TM400, 72 H-D SS350, 72 GT380, 75 Z1B, 77 XLH, 79 CB750K

Please Log in or Create an account to join the conversation.

  • hocbj23
  • hocbj23's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Oil Cooler Line

28 Dec 2010 17:27
#418962
When I put a cooler on my KZ,I went to a local industrial supply house and they had Goodyear hi pressure oil lines in the right id/od in both red and black colors.Might try one locally or if u cant find any let me know what u need and I will see if I can get it here and send it to u.bj

Please Log in or Create an account to join the conversation.

  • stonemaster
  • stonemaster's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Oil Cooler Line

28 Dec 2010 17:50 - 28 Dec 2010 17:52
#418968
go to NAPA or any decent auto parts store, no use testing an oil line, if u have any doubt, get new stuff, dont cost much even for the good stuff
Last edit: 28 Dec 2010 17:52 by stonemaster.

Please Log in or Create an account to join the conversation.

  • grumpy56
  • grumpy56's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 310
  • Thanks: 6

Re: Oil Cooler Line

28 Dec 2010 17:59
#418970
Thank you both. Will try NAPA or an industrial supply store tomorrow and thanks for the offer bj
Lewis
1982 KZ1000-J2
2006 HD FXD35
1970 Suzuki T350
1972 Suzuki GT380 (In-Process)
In The Past...71 TM400, 72 H-D SS350, 72 GT380, 75 Z1B, 77 XLH, 79 CB750K

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Oil Cooler Line

28 Dec 2010 18:13
#418974
These are low pressure lines with pressures of 2.2-2.8 PSI, I replaced my Kawasaki supplied lines with new ones from Earl's supply some years ago.

I took a Dremel tool with a cut off wheel and opened up the crimp end of the hose fittings. 3/8" I.D. hose should fit.

I've found that using the fuel injection hose clamps will make for a tight fit without the squeeze out through the standard "worm" hose clamps.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • keith1
  • keith1's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1646
  • Thanks: 3

Re: Oil Cooler Line

28 Dec 2010 18:39
#418981
low pressure system equals use whatever you want....
i used -8 or -10(cant remember off hand) with hose clamps and chrome covers to my cooler.....for reference each "-" equals 1/16 inch....-8 would be 1/2 inch......i ran mine around the right hand side of motor and freed up space under the tank where the rubber lines had been.....

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Oil Cooler Line

29 Dec 2010 05:52
#419085
I would pull the adapter block from the engine, where the switch and lines come out. It takes a 6mm Allen wrench for two bolts. There is three O-rings under it, this has leaked on both of my "J" bikes.
Check this thread;
kzrider.com/index.php?option=com_kunena&...ew&catid=2&id=402420
:)
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • otakar
  • otakar's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 5069
  • Thanks: 29

Re: Oil Cooler Line

29 Dec 2010 06:25
#419095
I will be mounting an oil cooler on my GPz1150 this spring. I plan on using stainless "gas flex" for the job. Mainly because in itself it will work as a part of the oil cooler. The line itself will dissipate a lot of heat. In this way, a very small cooler will dump a lot of heat by the time the oil will get back to the engine.
74 Z1-A stock
76 KZ-900 Totaly stock vice MAC pipe
77 KZ-1000A stock
78 Z1-R 100%MINT 500 original Mi.
78 Z1-R Yoshi 1103 kit stage 1 cams Yoshi pipe. Etc
79 KZ-1300 (1400)
80 KZ-1300
81 Scratch built GPz1150R
82 KZ1000

Please Log in or Create an account to join the conversation.

  • grumpy56
  • grumpy56's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 310
  • Thanks: 6

Re: Oil Cooler Line

29 Dec 2010 07:03
#419104
Good idea on the adapter block and lines. I will pull the adapter and find some new O rings. I have not removed the carbs and it is tight in there, but should be able to get it off and re-install it and the oil line.
Lewis
1982 KZ1000-J2
2006 HD FXD35
1970 Suzuki T350
1972 Suzuki GT380 (In-Process)
In The Past...71 TM400, 72 H-D SS350, 72 GT380, 75 Z1B, 77 XLH, 79 CB750K

Please Log in or Create an account to join the conversation.

  • hocbj23
  • hocbj23's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Oil Cooler Line

29 Dec 2010 07:51
#419107
grumpy56 wrote:
Good idea on the adapter block and lines. I will pull the adapter and find some new O rings. I have not removed the carbs and it is tight in there, but should be able to get it off and re-install it and the oil line.
Local Harbor Freight tool place had a box of viton O rings (assorted sizes) for 8 bucks recently.Might try them if the OEM stuff is hard to find.bj

Please Log in or Create an account to join the conversation.

  • grumpy56
  • grumpy56's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 310
  • Thanks: 6

Re: Oil Cooler Line

29 Dec 2010 08:37
#419114
Just removed the adapter. O rings do not look bad, but will replace them anyhow. However, there is an 11mm (head) bolt on the rear of the adapter that screws into the housing that has a rubber gasket/insert That one looks "squished" and the bolt was loose. What purpose does that bolt serve? One of the larger O rings circles it.
Lewis
1982 KZ1000-J2
2006 HD FXD35
1970 Suzuki T350
1972 Suzuki GT380 (In-Process)
In The Past...71 TM400, 72 H-D SS350, 72 GT380, 75 Z1B, 77 XLH, 79 CB750K

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum