advice for valve inspection
- ace
-
Topic Author
- Offline
- User
-

Registered
- 78kz1000
- Posts: 73
- Thanks: 1
advice for valve inspection
09 Jan 2011 03:52
what should i see when i pull valve cover?1000 motor has 40k but runs well. should i upgrade?? let me know plz as i dunno what if any service has been done internally.... does have blue sealer showin so i know somebodys been inside thanx ace.
78kz1000
Please Log in or Create an account to join the conversation.
- Nebr_Rex
-
- Offline
- User
-

Registered
- Posts: 1889
- Thanks: 295
Re: advice for valve inspection
09 Jan 2011 04:19
Have you done a compression test?
2002 ZRX1200R
81 GPz1100
79 KZ1000st daily ride
79 KZ1000mk2 prodject
78 KZ650sr
78 KZ650b
81 KZ750e
80 KZ750ltd
77 KZ400/440 cafe project
76 KZ400/440 Fuel Injected
www.dotheton.com/index.php?threads/dr-je...air-of-kz400s.39120/
.
81 GPz1100
79 KZ1000st daily ride
79 KZ1000mk2 prodject
78 KZ650sr
78 KZ650b
81 KZ750e
80 KZ750ltd
77 KZ400/440 cafe project
76 KZ400/440 Fuel Injected
www.dotheton.com/index.php?threads/dr-je...air-of-kz400s.39120/
.
Please Log in or Create an account to join the conversation.
- ace
-
Topic Author
- Offline
- User
-

Registered
- 78kz1000
- Posts: 73
- Thanks: 1
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: advice for valve inspection
09 Jan 2011 07:09
ace wrote:
Would first measure clearances.
Keep good clear notes of existing gap for each valve.
If out of spec, then re-shim as required.
Sometimes an existing shim may be used with another valve, which could reduce number of new shims required.
Keep good clear notes of shim size and clearance on each valve, so this info will be available next time the clearances are checked.
Unless existing gasket is perfect, would install a new gasket when reassembling.
First assure mating surfaces are perfectly clean and pristine.
Install dry. And it won't leak (at least mine never do).
A thin film of silicone sealant may be applied around each half-moon just before installing the gasket.
Good Fortune!
what should i see when i pull valve cover?1000 motor has 40k but runs well. should i upgrade?? let me know plz as i dunno what if any service has been done internally.... does have blue sealer showin so i know somebodys been inside thanx ace.
Would first measure clearances.
Keep good clear notes of existing gap for each valve.
If out of spec, then re-shim as required.
Sometimes an existing shim may be used with another valve, which could reduce number of new shims required.
Keep good clear notes of shim size and clearance on each valve, so this info will be available next time the clearances are checked.
Unless existing gasket is perfect, would install a new gasket when reassembling.
First assure mating surfaces are perfectly clean and pristine.
Install dry. And it won't leak (at least mine never do).
A thin film of silicone sealant may be applied around each half-moon just before installing the gasket.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
