Do check valve clearances!!! -Visual

  • calvin17d
  • calvin17d's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 187
  • Thanks: 2

Do check valve clearances!!! -Visual

09 Jan 2011 18:27 - 09 Jan 2011 18:50
#421107
If you take a look at the right side of the valve you can see the hairline crack. There are actually 2 others as well, but im not sure they are visible.

I decided to check compression before starting the detail and minor restoration of my 76 kz900. Compression was slightly below spec (120 psi on avg.) for 3 of 4 cylinders while #3 was only giving me 30 psi. I poured oil into the cylinder as the troubleshooting method would suggest. The pressure increased to 75 psi. This would typically mean that the issue is not the valves and is related to ring/bore size. Further dismantling the bike I found that all the cylinders and rings were slightly worn but still in good condition and not exceeding any wear limits. My assumption was that my gasket had gone bad (although no signs), or that the rings were bad. I kept hoping that perhaps the valve was the culprit, and indeed it was. This flaw in the valve would never have been found if I hadnt removed the valves and cleaned off carbon.

The moral of my little story is that relying on the oil test to determine cause of compression loss may not be an accurate method, additionally, valve clearance will not only cause poor performance and although that may seem to be common knowledge to most, I was unaware that neglecting could also lead to catastrophic failure internally. I was unable to fit my smallest feeler when checking clearances and on 4 of 8 valves I had to insert shims with a difference in shim number of 20 or clearance of .020, wow!

1976 Kz900 A4
Last edit: 09 Jan 2011 18:50 by calvin17d.

Please Log in or Create an account to join the conversation.

  • mjg15
  • mjg15's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 698
  • Thanks: 18

Re: Do check valve clearances!!! -Visual

09 Jan 2011 19:47
#421134
Nice Find ! You cant take too much for granted on these 30+ year old bikes. Good thing that they were built tough, I'm not thinking that today's FEA engineered, 15,000 RPM masterpieces are going to stand the test of time so well.
'80 Z750fx
'81 KZ550A
'81 GPz550's, Too many!
'82 KZ1000R
'82 GPz750
'90 ZR550


Project photo album: s163.photobucket.com/albums/t289/mg15_ph...GPz-ZR550%20project/
s163.photobucket.com/albums/t289/mg15_ph...current=DSC01286.jpg

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Do check valve clearances!!! -Visual

09 Jan 2011 21:08
#421149
Ouch.
Leak down test would have showed the valve problem, but by the time there that bad, rings would be a very good idea. Hope you have a way to cut your seats, it wouldn't be a good Idea to lap new valves to those seats. Maybe a trip to a machine shop?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • calvin17d
  • calvin17d's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 187
  • Thanks: 2

Re: Do check valve clearances!!! -Visual

10 Jan 2011 19:51
#421384
This valve is the only one that I believe to have been constantly stuck open. The rest looked great and the seat of this valve is not in bad shape either. New rings on the way. I am going to attempt to lap a new valve into this seat and give it shot. Thanks.
1976 Kz900 A4

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum