Exhaust Question

  • BIGKEVIN
  • BIGKEVIN's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 419
  • Thanks: 1

Exhaust Question

20 Jan 2011 16:41
#423955
I have a 1976 KZ900 with a 4 into 1 Vance and Hines pipe. I just got the bike a couple of months ago. While working on it this winter, I notices that where the header pipe connects to the rear portion, the megaphone, there was some clay like stuff to stop the exhuast leak. There is no clamp or gasket. Is there a place that I can order the gasket or clamp to connect to two together properly ? Also, I noticed that some the studs where the header connects to the engine are stripped/rusted. Are all of the studs screwed into the engine ? I plan on replacing all of the studs.
1976 KZ900
2006 ZX6R

Please Log in or Create an account to join the conversation.

  • Mcdroid
  • Mcdroid's Avatar
  • Offline
  • Sustaining Member
  • Sustaining Member
    Registered
  • Gone Kwackers
  • Posts: 6909
  • Thanks: 530

Re: Exhaust Question

20 Jan 2011 16:53
#423959
The V&H I have may be similar to the one you have. The muffler slips on to the collector BUT the muffler does not have a split end (whereas the muffler on a Kerker does have split tabs...which a clamp compresses making a seal). Absence of those splits on a V&H will not allow the pipe to be compressed around the collector...hence the use of some sort of sealing compound. As for replacing exhaust studs, I think there are a number of threads on this forum that will aid you...and they do thread into the head.
Michael
Victoria, Texas

1982 GPz750
1977 KZ1000A
1978 KZ1000A
1982 GPz1100
1975 Z2A

Please Log in or Create an account to join the conversation.

  • hocbj23
  • hocbj23's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Exhaust Question

20 Jan 2011 16:55
#423961
My Vance and Hines is slip fit-the megaphone just pushes up onto the headpipe.No "goop" required.There is a bracket that is bolted to the frame to keep the megaphone from slipping off

Please Log in or Create an account to join the conversation.

  • andy9802gt
  • andy9802gt's Avatar
  • Offline
  • User
  • User
    Registered
  • If it tastes that good, eat it yourself.
  • Posts: 695
  • Thanks: 19

Re: Exhaust Question

20 Jan 2011 16:59
#423963
Use red RTV silicone(the high heat stuff). I run a medium sized bead around the inside of the muffler and a smaller one around the end of the collector, slip them together and tighten the mounting bolts, let sit for 24hrs minimum, and you'll be good to go. Don't be suprised when you start it and it blows the dried excess out the end of your pipe.:laugh:
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Exhaust Question

20 Jan 2011 16:59 - 20 Jan 2011 17:01
#423964
BIGKEVIN wrote:
I have a 1976 KZ900 with a 4 into 1 Vance and Hines pipe. I just got the bike a couple of months ago. While working on it this winter, I notices that where the header pipe connects to the rear portion, the megaphone, there was some clay like stuff to stop the exhuast leak. There is no clamp or gasket. Is there a place that I can order the gasket or clamp to connect to two together properly ? Also, I noticed that some the studs where the header connects to the engine are stripped/rusted. Are all of the studs screwed into the engine ? I plan on replacing all of the studs.

V&H 4>1 are designed to fit closely without needing a clamp or gasket.

Could apply High-Temp Copper Permatex sealant. But don't overdo it. Just use a thin strip around header where muffler will barely push over and cover the sealant strip when the muffler is being installed. This is so it may be taken apart in the future if desired.

The exhaust studs are replaceable.
Z1E carries the exhaust studs.
Click > www.z1enterprises.com/detail.aspx?ID=100

Good Fortune! :)
1973 Z1
KZ900 LTD
Last edit: 20 Jan 2011 17:01 by Patton.

Please Log in or Create an account to join the conversation.

  • BIGKEVIN
  • BIGKEVIN's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 419
  • Thanks: 1

Re: Exhaust Question

20 Jan 2011 17:05
#423968
I have already ordered the studs from Z1. I was just wondering if all 8 of them screw into the head, which is think that they do. Thanks for the info also on the sealant.
1976 KZ900
2006 ZX6R

Please Log in or Create an account to join the conversation.

  • andy9802gt
  • andy9802gt's Avatar
  • Offline
  • User
  • User
    Registered
  • If it tastes that good, eat it yourself.
  • Posts: 695
  • Thanks: 19

Re: Exhaust Question

20 Jan 2011 17:08
#423970
Yep. All the studs screw into the head. If you don't use flange nuts you'll have to use lock washers on the collars.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm

Please Log in or Create an account to join the conversation.

  • Old Man Rock
  • Old Man Rock's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6071
  • Thanks: 225

Re: Exhaust Question

21 Jan 2011 16:32
#424198
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter

Phoenix, Az

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum